ECU Citroen C4 PICASSO 2009 1.G Owner's Manual

22
F A M I L I A R I S A T I O N
Seat belts not fastened/
unfastened warning lamp This warning lamp informs you
if the driver’s or front passen-
ger’s seat belt is not fastened
(depending on model), and if
the front passenger’s (depend-
ing on model) or the second-
row passengers’ seat belts are
unfastened. The lit up positions
represent those whose seat belts are
not fastened/unfastened.
You can use electrical central locking or
unlocking by pressing on button A .
If one of the doors is open or is not
closed properly, central locking will not
work. Tyre deflation detection
This function warns you if a tyre is de-
fl ated or punctured.
This system does not absolve the driver
of the need to regularly check the tyre
pressures.
The service warning lamp
lights up, and a vehicle out-
line is displayed, accompa-
nied by a message and a
sound signal.
Defl ation warning
The STOP warning lamp lights
up, and a vehicle outline is
displayed, accompanied by a
message and a sound signal.
Puncture

 30

 114
Anti-intrusion security
Once the function has been activated,
when starting the engine, the system
automatically locks the doors once you
reach approximately 10 km/h (approxi-
mately 6 mph).
This function can be deactivated
by pressing button
A for more than
two seconds.
 78
M O N I T O R I N G
Locking from inside
Instrument panel
with multifunction screen A

 24
with multifunction screen C
 25
with NaviDrive multifunction screen
 26

1. Instrument panel.

2. Multifunction screen.

3. Control buttons.

4. Warning lamps display zone.

59
III
C O M F O R T
Storing driving positions
System which takes into account the
electrical settings of the driver's seat
and exterior mirrors. It enables you
to store up to two positions using the
buttons on the side of the driver's
seat. Storing a position
Using buttons M/1/2

 Switch on the ignition.

 Adjust your seat and the exterior
mirrors.

 Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the position has been
stored.
Storing a new position cancels the
previous position. Recalling a stored position
Ignition on or engine running

 Briefl y press button 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery.
Vehicle moving

 Press and hold button 1 or

2 until the audible signal is
heard indicating the end of the
adjustment.

Do not try to store a driving position
while driving.

96
VI
L A Y O U T
MATS
Removable component which pro-
tects the carpet against exterior dirt.
Fitting
When fi tting the mat for the fi rst time,
on the driver's side, use only the fi xings
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:

 move the seat as far back as possible,

 unclip the fi xings,

 remove the mat.
Refitting
To refi t the mat on the driver's side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured
correctly. To avoid any risk of jamming of the
pedals:
- only use mats which are suited
to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of an- other.
Front door
The front door pockets can hold objects
equivalent in volume to a 1.5 litre bottle.
They may have their own lighting,
coming on automatically when your
hand approaches.
This lighting goes out automatically
after a few moments when your
hand is taken away.
Rear door
The rear door pockets can hold objects
equivalent in volume to a 0.5 litre bottle.
USB BOX
This connection box, consisting of
a JACK socket and a USB port, is
located on the centre console.
It permits the connection of portable
equipment, such as a digital audio
player of the iPod ®
or USB stick type.
It reads the audio fi le formats which
are transmitted to your audio equip-
ment and played via the vehicle's
speakers.
You can manage these fi les using
the steering wheel controls or the
audio equipment control panel and
display them on the multifunction
screen.
When it is in use, the portable equip-
ment charges automatically.
For further details concerning the
use of this equipment, refer to the
"Audio and Telematics" section.

96
VI
L A Y O U T
MATS
Removable component which pro-
tects the carpet against exterior dirt.
Fitting
When fi tting the mat for the fi rst time,
on the driver's side, use only the fi xings
provided in the wallet attached.
The other mats are simply placed on
the carpet.
Removal
To remove the mat on the driver's side:

 move the seat as far back as possible,

 unclip the fi xings,

 remove the mat.
Refitting
To refi t the mat on the driver's side:

 position the mat correctly,

 refi t the fi xings by pressing,

 check that the mat is secured
correctly. To avoid any risk of jamming of the
pedals:
- only use mats which are suited
to the fi xings already present in
the vehicle; it is imperative that
these are used,
- never fi t one mat on top of an- other.
Front door
The front door pockets can hold objects
equivalent in volume to a 1.5 litre bottle.
They may have their own lighting,
coming on automatically when your
hand approaches.
This lighting goes out automatically
after a few moments when your
hand is taken away.
Rear door
The rear door pockets can hold objects
equivalent in volume to a 0.5 litre bottle.
USB BOX
This connection box, consisting of
a JACK socket and a USB port, is
located on the centre console.
It permits the connection of portable
equipment, such as a digital audio
player of the iPod ®
or USB stick type.
It reads the audio fi le formats which
are transmitted to your audio equip-
ment and played via the vehicle's
speakers.
You can manage these fi les using
the steering wheel controls or the
audio equipment control panel and
display them on the multifunction
screen.
When it is in use, the portable equip-
ment charges automatically.
For further details concerning the
use of this equipment, refer to the
"Audio and Telematics" section.

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.

102
VI
L A Y O U T
HIGH CARGO NET (GRAND C4 PICASSO)
This enables you to maximise the
vehicle’s loadspace.
It retains objects, preventing them
from sliding towards the front of the
passenger compartment.

You insert it under the roller of the
luggage-cover blind, securing it
on the third-row side mouldings. Position 1
5-seat confi guration; installed behind
the second row.

Installing the roller

 Remove the protective covers
located under the blind roller
notches.

 Position the roller under that of
the luggage-cover blind.

 Raise the fl ap on the blind, posi-
tioning it on top of the blind.

 Deploy the net, passing it between
the rollers and the seats.

 Pull the net upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).

Removing the roller

 Perform these operations in re-
verse order. Position 2
2-seat confi guration; installed behind
the fi rst row.

Removing the roller

 Carry out these operations in
reverse order.

Installing the roller

 With the second-row seats folded
away, remove the covers of the
Isofi x anchoring points located on
the seat backrests.

 Secure the roller on the Isofi x
anchoring points.

 Deploy the net and pull it upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).

103
VI
L A Y O U T
LUGGAGE RETAINING NET (C4 PICASSO)
There are 8 anchoring rings in the
boot to enable you to secure your
luggage:
- 1, 2, 3 and 4 on the boot fl oor,
- 5, 6, 7 and 8 on the boot pillars.
LUGGAGE RETAINING NET (GRAND C4 PICASSO)
There are 8 anchoring rings in the
boot to enable you to secure your
luggage:
- 1 and 2 underneath the luggage-
cover blind,
- 3, 4, 7 and 8 on the boot fl oor,
- 5 and 6 on the boot pillars. For reasons of safety in the event of
sudden braking, it is recommended
that you place heavy objects on the
fl oor as close as possible to the
backrests of the second-row seats.
The luggage retaining net gives you a
number of confi gurations depen-ding
on which of the anchoring rings you
attach it to (hammock format, vertical/
horizontal, on the fl oor or behind the
second row seats), enabling you to
secure a variety of objects in the boot.

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.

100
VI
L A Y O U T
MODUBOX (C4 PICASSO)
Equipment for use both inside the
vehicle and away from the vehicle.
It is composed of a shopping trol-
ley and a fl exible bag (isotherm on
some versions) which can be used
independently of each other depen-
ding on your needs (by detaching
the fastenings on each side at the
top and bottom).
To use

 Unhook the red strap to free the
Modubox.

 Unhook the black strap then press
on the round buttons on either side
of the Modubox simultaneously to
deploy it. Use of the Modubox outside
the vehicle
Stowage inside the vehicle

 Perform the operations in reverse
to fold and stow inside the vehicle.

 If you have used your Modubox
away from the vehicle, take care to
reposition it correctly in the housings provided for this purpose.
BAG HOOK
LUGGAGE-COVER BLIND (GRAND C4 PICASSO)
Position 1
5-seat confi guration; installed be-
hind the second-row seats, with the
third-row seats folded away.

 Press on the recess on the left
hand side of the Modubox to
raise (or lower) the handle.
Located on the left-hand interior wall
of the boot, this permits the securing
of shopping bags.
Installing the roller

 Position the left-hand end of the
blind roller in notch A .

 Compress the right-hand end of
the roller and place it in notch B .

 Unroll the blind until it reaches
the boot pillars.

 Insert the guides of the blind into
the rails on the pillars.

Removing the roller


Perform these operations in reverse
order.

102
VI
L A Y O U T
HIGH CARGO NET (GRAND C4 PICASSO)
This enables you to maximise the
vehicle’s loadspace.
It retains objects, preventing them
from sliding towards the front of the
passenger compartment.

You insert it under the roller of the
luggage-cover blind, securing it
on the third-row side mouldings. Position 1
5-seat confi guration; installed behind
the second row.

Installing the roller

 Remove the protective covers
located under the blind roller
notches.

 Position the roller under that of
the luggage-cover blind.

 Raise the fl ap on the blind, posi-
tioning it on top of the blind.

 Deploy the net, passing it between
the rollers and the seats.

 Pull the net upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).

Removing the roller

 Perform these operations in re-
verse order. Position 2
2-seat confi guration; installed behind
the fi rst row.

Removing the roller

 Carry out these operations in
reverse order.

Installing the roller

 With the second-row seats folded
away, remove the covers of the
Isofi x anchoring points located on
the seat backrests.

 Secure the roller on the Isofi x
anchoring points.

 Deploy the net and pull it upwards.

 Anchor it to the roof by means of
the fi xing points (after you have
removed their covers).