Vent CITROEN C4 PICASSO 2011 Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2011, Model line: C4 PICASSO, Model: CITROEN C4 PICASSO 2011Pages: 352, PDF Size: 10.66 MB
Page 82 of 352
Downloaded from www.Manualslib.com manuals search engine IV
80
ACCESS
Deadlocking using the key
)
Turn the key to the right in the driv-
er's door lock to lock the vehicle
completely and hold it in this posi-
tion for more than two seconds to
close the windows automatically
in addition to locking.
)
Turn the key to the right again
within fi ve seconds to deadlock
the vehicle.
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual cen-
tral control button.
Therefore, never leave anyone in-
side the vehicle when it is dead-
locked. Deadlocking also triggers the timed
illumination of the exterior side spot
lamps and guide-me-home lighting,
if this is activated.
)
First press this button to fold the
key.
If you do not press the button when
folding the key, there is a risk of
damage to the mechanism.
Locating your vehicle
This function allows you to identify
your vehicle from a distance, espe-
cially when the light is poor. Your ve-
hicle must be locked.
)
Press the closed padlock on the
remote control.
This will bring on the courtesy lamps
and exterior side spotlamps, as well
as fl ashing the direction indicators
for a few seconds.
Remote operation of lighting
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code
must be recognised in order for
starting to be possible.
This electronic engine immobiliser
locks the engine management sys-
tem a few minutes after the ignition
is switched off and prevents starting
of the engine by anyone who does
not have the key.
In the event of a fault,
you are informed by il-
lumination of this warn-
ing lamp, an audible
signal and a message in the screen.
In this case, your vehicle will not
start; contact a CITROËN dealer as
soon as possible.
Keep safely the label attached to the
keys given to you on acquisition of
the vehicle.
Folding the key
A press on this button
brings on the temporary
illumination of sidelamps,
dipped beam headlamps,
number plate lamps and
the exterior side spotlamps located
underneath the door mirrors.
A second press before the end of the
timed period cancels the command.
Deadlocking is confi rmed by fi xed
lighting of the direction indicators for
approximately two seconds.
According to version, the door mir-
rors fold at the same time.
Page 83 of 352
Downloaded from www.Manualslib.com manuals search engine IV
81
ACCESS
STARTING
1. "S": Steering lock
To unlock the steering, gently move
the steering wheel while turning the
key, without forcing it.
2. "M": Ignition on
Depending on the version of your
vehicle, the orange and red warn-
ing lamps should also come on for
a short time.
3. "D": Starter
Release the key as soon the engine
has started.
If the fi rst attempt fails, switch off the
ignition. Wait ten seconds then oper-
ate the starter again.
Steering lock
1. "
S":
After removing the key, turn
the steering wheel to lock the
steering. The key can only be
removed in position S
.
2. "M":
Ignition switched on, the
steering is unlocked (by turning
the key to position M
, move
the steering wheel gently if
necessary).
3. "D":
Starter position.
Key left in position "M"
audible warning
If you forget to remove the key from
the ignition, the ignition is switched
off automatically after one hour.
To switch the ignition back on, turn
the key to position S
then back to
position M
.
Do not run the engine in an en-
closed space or where there is
insuffi cient ventilation
.
You must always to keep the
engine running when moving in
order to retain braking and steer-
ing power assistance .
Never remove the ignition key
before the vehicle has come to a
complete stop.
Vehicles equipped with a
turbocharger
Never stop the engine without having
allowed it to run for a few seconds at
idle, this being the time required for
the turbocharger to return to a normal
speed.
Flicking the accelerator at the mo-
ment of switching off the ignition
could cause serious damage.
A heavy object (key fob...), attached
to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction. Never turn the key to this position
when the engine is running.
Page 84 of 352
Downloaded from www.Manualslib.com manuals search engine IV
82
ACCESS
Remote control problems
Following disconnection of the ve-
hicle battery, replacement of the re-
mote control battery or in the event
of a remote control malfunction, you
can no longer unlock, lock or locate
your vehicle.
)
First of all, use the key in the lock
to unlock or lock your vehicle.
)
Then, reinitialise the remote control.
Reinitialisation
)
Switch off the ignition.
)
Turn the key to position 2 (Ignition on)
.
)
Press the closed padlock imme-
diately for a few seconds.
)
Switch off the ignition and re-
move the key from the ignition
switch.
The remote control is fully opera-
tional again. Battery ref.: CR1620/3 volts.
If the remote control bat-
tery is fl at, you are in-
formed by lighting of this
warning lamp, an audible
signal and a message on
the multifunction screen.
)
Unclip the casing using a coin at
the notch.
)
Slide the fl at battery out of its lo-
cation.
)
Slide the new battery into its lo-
cation observing the original di-
rection.
)
Clip the casing together.
)
Reinitialise the remote control.
Changing the battery
If the problem persists, contact a
CITROËN dealer as soon as pos-
sible.
Page 88 of 352
Downloaded from www.Manualslib.com manuals search engine IV
86
ACCESS
ELECTRIC WINDOWS
System intended to open or close a
window manually or automatically.
Fitted with a safety anti-pinch system
and a system for deactivation in the
event of misuse of the rear controls.
1.
Driver's electric window
control.
2.
Passenger's electric window
control.
3.
Rear right electric window
control.
4.
Rear left electric window
control.
5.
Deactivation of the rear
electric window and door
controls.
One-touch electric windows
There are two options:
- automatic mode
)
Press or pull the control
fi rmly. The window opens or
closes fully when the control is
released.
)
Pressing the control again
stops the movement of the
window.
The electric window controls re-
main operational for approximately
45 seconds after the ignition is
switched off or until the vehicle is
locked after a door is opened.
If one of the passenger windows
cannot be operated from the driv-
er's door control panel, carry out
the operation from the control
panel of the passenger door con-
cerned, and vice versa.
Safety anti-pinch
When the window rises and meets
an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for
example, in the presence of ice),
immediately after the movement is
reversed:
)
press and hold the control until
the window opens fully,
)
then pull the control immediate-
ly and hold it until the window
closes,
)
continue to hold the control for
approximately one second after
the window has closed.
The safety anti-pinch function
is not operational during these
operations.
- manual mode
)
Press or pull the control gently.
The window stops when the
control is released.
Page 89 of 352
Downloaded from www.Manualslib.com manuals search engine IV
87
ACCESS
Reinitialisation
If a window does not rise automati-
cally, its operation must be reini-
tialised:
)
pull the control until the window
stops,
)
release the control and pull it
again until the window closes
fully,
)
continue to hold the control for
approximately one second after
the window has closed,
)
press the control to lower the
window automatically to the low
position,
)
when the window has reached
the low position, press the con-
trol again for approximately
one second.
The safety anti-pinch function
is not operational during these
operations.
Deactivation of the rear
electric window and door
controls
)
For the safety of your children,
press control 5
to deactivate the
rear electric window controls re-
gardless of their position. Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during
operation of the electric windows,
you must reverse the movement of
the window. To do this, press the
control concerned.
When the driver operates the con-
trols for the passengers' electric
windows, they must ensure that no
one is preventing correct closing of
the windows.
The driver must ensure that the
passengers use the electric win-
dows correctly.
Be aware of children when operat-
ing the windows.
This warning lamp comes
on temporarily on the instru-
ment panel on deactivation
and each time the ignition is
switched on.
This control also deactivates the
interior controls for the rear doors
(refer to the section "Child safety -
Electric child lock").
Page 91 of 352
Downloaded from www.Manualslib.com manuals search engine IV
89
ACCESS
Unlocking
)
Press this button again to unlock
the vehicle.
The red indicator lamp on the button
goes off.
If the vehicle is locked or dead-
locked from the outside, the red in-
dicator lamp fl ashes and button A
is inactive.
)
In this case, use the remote
control or the key to unlock the
vehicle.
Automatic central locking
This system automatically locks the
doors, boot and rear screen while
driving.
You can activate or deactivate this
function.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors, the boot and
the rear screen lock automatically.
Unlocking
)
Above 6 mph (10 km/h), press
this button to unlock the doors,
the boot and the rear screen
temporarily.
Ignition on:
Deactivation
)
Press this button again for more
than two seconds.
A confi rmation message appears in
the multifunction screen.
Emergency control
System which locks or unlocks the
doors mechanically in the event of
a malfunction of the battery or of the
central locking.
Locking the driver's door
)
Insert the key in the lock, then
turn it to the right.
Unlocking the driver's door
)
Insert the key in the lock, then
turn it to the left.
Locking the front and rear
passenger doors
)
Insert the key in the lock, located
on the edge of the door, then turn
it one eighth of a turn
.
Unlocking the front and rear
passenger doors
)
Pull the interior door opening
control.
If one of the doors or the boot or
rear screen is open, the automat-
ic central locking does not take
place. Activation
)
Press this button for more than
two seconds.
A confi rmation message appears in
the multifunction screen. In the event of a fault with the cen-
tral locking, you must disconnect
the battery to lock the boot and so
ensure the complete locking of the
vehicle.
Page 93 of 352
Downloaded from www.Manualslib.com manuals search engine IV
91
ACCESS
Emergency boot release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking
)
Fold back the rear seats to gain
access to the lock from inside
the boot.
)
Insert a small screwdriver into
hole A
of the lock to unlock the
tailgate.
)
Push the white part, located in-
side the lock, to the left to unlock
the boot.
PANORAMIC SUNROOF
It is fi tted with an electrically con-
trolled blind.
Opening the roof blind
)
Rotate the control knob B
to slide
the roof blind to the desired posi-
tion (positions 1
to 9
).
Closing the roof blind
)
Rotate the control knob B
to po-
sition 0
to close the roof blind.
Recommendations
- Pressing the locking button on
the remote control for more than
two seconds will close the blind
(practical when, for example,
you leave your vehicle in a sunlit
car park).
- On returning to your vehicle, a
press on control knob B
reposi-
tions the blind to the last position
selected.
Anti-pinch
The blind has an anti-pinch func-
tion.
At the end of its travel, when the blind
encounters an obstacle on closing, it
stops and moves back slightly.
Following a fault or after a battery
disconnection during the movement
of the blind or after it has stopped,
you must re-initialise the anti-pinch
function:
)
place the blind in the closed po-
sition,
)
press control knob B
for approxi-
mately two seconds.
Page 95 of 352
Downloaded from www.Manualslib.com manuals search engine IV
93
ACCESS
The petrol or Diesel engine of your ve-
hicle is fi tted with a catalytic converter, a
device which helps to reduce the level of
harmful emissions in the exhaust gases.
For petrol engines, you must use
unleaded fuel.
The fi ller neck is narrower, allowing only
unleaded petrol nozzles to be intro-
duced.
If you have put in the wrong fuel
for your vehicle, you must have
the fuel tank drained and fi lled
with the correct fuel before start-
ing the engine.
Quality of the fuel used for
petrol engines
Quality of the fuel used for
Diesel engines
Fuel cut-off
Your vehicle is equipped with a safe-
ty device which cuts off the fuel sup-
ply in the event of a collision.
The petrol engines are perfectly
compatible with E10 or E24 type pet-
rol biofuels (containing 10 % or 24 %
ethanol), conforming to European
standards EN 228 and EN 15376.
E85 type fuels (containing up to
85 % ethanol) are reserved exclu-
sively for vehicles marketed for the
use of this type of fuel (BioFlex ve-
hicles). The quality of the ethanol
must comply with European stan-
dard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing
up to 100 % ethanol (E100 type).
The Diesel engines are perfectly
compatible with biofuels which con-
form to current and future European
standards (Diesel fuel which com-
plies with standard EN 590 mixed
with a biofuel which complies with
standard EN 14214) available at the
pumps (containing up to 7 % Fatty
Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this
use is subject to strict application
of the special servicing conditions.
Contact a CITROËN dealer or a
qualifi ed workshop.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or di-
luted, domestic fuel...) is strictly pro-
hibited (risk of damage to the engine
and fuel system).
Page 99 of 352
Downloaded from www.Manualslib.com manuals search engine V
97
VISIBILITY
Automatic illumination of
headlamps
When a low level of ambient light
is detected by a sunshine sensor,
the number plate lamps, sidelamps
and dipped beam headlamps are
switched on automatically, without
any action on the part of the driver.
They can also come on if rain is de-
tected, at the same time as auto-
matic operation of the windscreen
wipers.
As soon as the brightness returns
to a suffi cient level or after the wind-
screen wipers are switched off, the
lamps are switched off automatically.
Activation
)
Turn ring A
to the "AUTO"
posi-
tion. The activation of the function
is accompanied by a message in
the screen.
Deactivation
)
Turn ring A
to a position other
than "AUTO"
. Deactivation of
the function is accompanied by a
message in the screen.
Operating fault
In the event of a malfunction of the
sunshine sensor, the lamps comes
on, a message appears in the
screen, accompanied by an audible
signal.
Contact a CITROËN dealer or a
qualifi ed workshop.
Automatic "guide-me-home"
lighting
When the automatic illumination of
headlamps function is activated,
under low ambient light the dipped
beams headlamps come on au-
tomatically when the ignition is
switched off.
In fog or snow, the sunshine sensor
may detect suffi cient light. Therefore,
the lighting will not come on auto-
matically.
Do not cover the sunshine sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.
Programming
The activation and the duration of
the guide-me-home lighting can
be set in the vehicle confi guration
menu.
For a vehicle fi tted with the mono-
chrome screen A, the duration is fi xed.
Page 108 of 352
Downloaded from www.Manualslib.com manuals search engine VI
106
FITTINGS
UPPER STORAGE
COMPARTMENTS
There are large storage compart-
ments at the top of the dashboard,
one on the driver's side and one on
the passenger's side.
)
To open, press the button at the
bottom corner.
)
To close, lower the lid fully until it
clicks.
ILLUMINATED GLOVE BOX
It includes storage areas for a bottle of
water, the vehicle handbook pack, ...
Its lid has areas for storing a pen, a
pair of spectacles, tokens, cards, a
cup, fragrance cartridges...
)
To open the glove box, raise the
handle and lower the lid.
The lamp comes on automatically
when the lid is opened.
COOLED GLOVE BOX
It is cooled by a ventilation nozzle
that can be closed manually.
It is directly linked to the vehicle’s air
conditioning system, being supplied
with cooled air whatever the require-
ments of the passenger compart-
ment.
The cooling of your glove box only
operates when the engine is running
and the air conditioning is on.
For safety reasons, the
glove box should remain
closed when the vehicle is
moving. For safety reasons, the up-
per storage compartments
should be kept closed when
the vehicle is moving.