Back row CITROEN C4 PICASSO 2017 Owners Manual

62
Front armrest
Height adjustment
Second row seats
The 3 seats of the 2nd row are independent
and are the same width. Their backrests are
adjustable to adapt the boot load space. F

L

ower the armrest completely.
F

L

ift it again to the desired position (low,
intermediate or high).
F

O

nce it is in the high position, lift it to unlock
it and bring it to the low position.
Longitudinal adjustment
A. Longitudinal adjustment: lift the lever.
B. Tilt angle adjustment: pull the strap and
push the seat back.
C. Folding the seat: give a
firm upward pull
on the strap to unlock the seat.
D. Folding the seat from the back: pull the
strap then push the backrest for ward.
F

L
ift lever A , at the front of the seat cushion
and adjust the seat as required.
Ease of use and comfort

64
From outside the vehicle
From the boot, for example when loading F
G
ive a firm upward pull on strap C , as
shown by the arrow, to unlock the seat;
keep pulling the strap until the seat is
completely folded. Push the backrest
slightly for ward so that the backrest tilts
and folds over the cushion. The seat and
cushion fold down to the floor.
Replacing the seat
F If necessary, straighten the continuity panels of the 2nd row of seats and lock
them.
F

R
aise the backrest and push it back until it
latches into place. Before per forming any operations on the
rear seats, to avoid damage to the seat
belts, make sure that the side belts are
properly tensioned. The central seat belt
must be put away. Secure the buckles
of the three seat belts to their anchoring
points.
Continuity panels
You can fold the second row seat(s) directly
from the boot, after having first folded the third
row seats.
F

P
ull strap D to unlock the desired seat and
give the backrest a
slight push for ward. To
prevent any damage to the mechanism,
strap D will unclip if excessive force is
applied. It is just a
matter of clipping it back
into place to make the system operational
again.
Each seat has a
continuity panel at the bottom
of the backrest, which, once unfolded:
-

a
llows for a continuous loading sur face in
the boot, whatever the position of the seats,
-

p
revents objects from sliding beneath the
2nd row seats.
These continuity panels are not designed
to support a
weight greater than 30 kg.
Ease of use and comfort

65
Getting out of the vehicle
from third row seatsReplacing the seat from
outside the vehicle, with
door open
If passengers are seated in the third row seats:
F

m
anually push the seat and cushion back as
far as it can go; the seat does not return to
the maximum back position, leaving space
free for the third row passengers' legs,
F

f
old the cushion until it locks.
Make sure there is nothing on or under the
cushion of the seat you want to move.
If this system fails (lever E ), the third row
passengers can also get out after having
folded the backrest of the second row
seats using strap D .
Do not let children operate the seats
unsupervised.
F
P
ull lever E . The seat unlocks and the
cushion comes up against the backrest.
F

Ke

ep lever E up by pushing it for wards. The
seat and cushion slide towards the front
seat.
This frees space behind the seat, allowing
the third row seat passengers to get into their
seats.
F

L

ift lever E . The seat unlocks and the
cushion moves up to the backrest.
F

P

ush the backrest holding lever E upwards.
Third row seats
Concertina boards
The two rigid concertina boards, which are built
in to the vehicle, cover the two third row seats,
when these are in the folded away position.
Before moving the seats, make sure that
the trays behind the front row seats are
properly stowed.
Unlocking/Locking the continuity panels
F

B

efore unfolding the continuity panels,
check that the 2nd row seats are moved
back as far as possible.
F

S

lide the latch of the continuity panel
upwards to unlock it.
F

S

traighten out the continuity panel, then
slide the latch downwards to lock it.
Access to third row seats
Third row seats are accessed via the second
row lateral seats.
3
Ease of use and comfort

66
Each of the two boards can support
a maximum load of 100 kg.
Folding the concertina
boards
Pull the strap, the 3 parts of the board fold into
c oncertina form.
When the third row seats are straightened,
these folded concertina boards can be left:
-
ei

ther flat behind the seats,
-

o
r in the vertical position,
thus clearing the inside of the seat as a
storage
space.
Installing the seats Seat storage
F Remove the load space cover.
For more information on the Interior
fittings and particularly on the load space
cover, refer to the corresponding section.
F

S
traighten the continuity panels of the
second row of seats and lock them in place.
F

F
old the concertina board and straighten it
vertically.
F

P
ull strap F , located behind the backrest
of the seat. The backrest tilts backwards
bringing the cushion. The seat locks in the
open position. F
S traighten the continuity panels of the
second row of seats and lock them in place.
F

L
ower the head restraints.
F

C
orrectly position the concertina board
vertically behind the seat.
F

M
ake sure that the seat belts of the 3
rd row
of seats are correctly fastened to the loops
and that they do not have any creases.
F

P

ull strap G , located at the bottom of the
backrest of the seat. The seat is unlocked.
F

T

hen, push the backrest slightly for wards.
The backrest tilts and folds on the cushion.
The folded seat is arranged at the back of
its storage area provided for this purpose.
F

P

ut the concertina boards back above the
folded down seats.
Ease of use and comfort

67
Configuration examples
4 seats
3 seats
Transporting items
7
seats 6
seats
Transporting items
5
seats
4
seats
Before working on the seats of the third
row, straighten the rigid boards of the
seats of the second row and lock them in
place.
Do not try to fold a

seat in the third row
without having opened it until the backrest
is fully locked.
Do not leave objects on the cushion or
below the cushion of the seats of the third
row, when you fold them.
Do not guide strap G when storing the
seat, your may jam your fingers.
Do not let children manipulate the seats
unsupervised.
Seat modular design and
configuration
Configuration examples
5 seats
3
Ease of use and comfort

68
In order to easily adapt your interior
space, you can fold all of the rear seats
individually and fold them onto the second
row floor, and beneath the floor on the
third row. This gives you a continuous load
floor up to the back of the front seats.
Folding or unfolding the seats must only
be done with the vehicle stationary.
Steering wheel adjustment
F When stationary , pull the control lever
to release the steering wheel adjustment
mechanism.
F

A
djust the height and reach to suit your driving
position.
F

P
ush the control lever to lock the steering wheel.
As a safety measure, these adjustments
s hould only be carried out with the vehicle
stationary.
Mirrors
Door mirrors
Each fitted with an adjustable mirror glass
permitting the lateral rearward vision necessary
for overtaking or parking.
They can also be folded for parking in narrow
spaces.
Demisting – Defrosting
Demisting-defrosting of the door
mirrors operates with the engine
running, by switching on the heated
rear screen.
For more information on Rear screen
demist - defrost , refer to the associated
section.
Adjustment
As a safety measure, the mirrors should
b e adjusted to reduce the blind spots.
Objects seen in the mirror are in reality
closer than they appear.
Take this into account when assessing
the distance of vehicles approaching from
behind.
F

M
ove control A to the right or to the left to
select the corresponding mirror.
F

M
ove control B in any of the four directions
to adjust.
F

R
eturn control A to the central position.
Folding
F From outside: lock the vehicle using the
electronic key or the " K eyless Entry and
Starting" system.
F

F
rom inside: with the ignition on, pull
the control A from the central position
rearwards.
Ease of use and comfort

70
A child sur veillance mirror is installed above the
interior mirror. This allows you to keep watch
over the passengers in the back of the vehicle
and facilitates discussion between passengers
in the front and the back without needing to
adjust the mirror and without turning around. It
can be easily folded to avoid dazzle.
Ventilation
Air intake
The air circulating in the passenger
compartment is filtered and originates either
from the outside via the grille located at the
base of the windscreen, or from the inside in air
recirculation mode.
Air treatment
The incoming air follows various routes
depending on the controls selected by the
driver:
-
d
irect arrival in the passenger compartment
(air intake),
-
p

assage through a

heating circuit (heating),
-

p
assage through a cooling circuit (air
conditioning).
Control panel
The controls of this system are accessible in the
Air conditioning menu of the touch screen A .
The demisting/defrosting controls for the
windscreen and rear screen are located to the
left of the touch screen.
Air distribution
1. Windscreen demisting/defrosting vents. 2.
Front quarter window demisting/defrosting
vents.
3. Front side window demisting/defrosting
vents.
Adjustable and closable side air vents.
4. Adjustable and closable central air vents.
5. Air outlets to the front footwells.
6. Side vents of the 2
nd row.
7. Air outlets to the rear footwells of the
second row.
8. Sunshine sensor.
Ease of use and comfort

84
Rear fittings
Aircraft trays
Closed tray
Open tray
These trays, fixed to the back of the front
seats, includes a recessed cup holder A and
a retaining strap B . For security reasons, these trays retract
downwards if excessive pressure is exerted.
Individual reading lamp
Side blinds
F Pull the tab A and anchor the blind on the
hook B .
Fitted to the windows in row 2, they protect the
passenger compartment from the sun's rays.
The reading lamps C may be integrated into
the backrests of the front seats, behind the
trays. They illuminate the top of the tray without
disturbing the other passengers.
They are only accessible when the tray is
lowered.
F

P

ress the "On/Off " button to switch the
reading lamp on or off.
F

P

ull the tray to lower it.
F

T

o fold the tray away, pull it up to the locking
latch.
Storage boxes
There are two storage boxes located beneath
the rear passenger footwells.
To open them, lift the cover by the notch.
Ease of use and comfort

87
To fold the 3rd row seats with the roller stored at
the back, it is necessary to raise the concertina
boards in order to give access to the seat
unlocking controls (red straps). When sharp deceleration occurs, objects
placed on the load space cover can turn
into projectiles.
Courtesy lampsFront – rear courtesy lamps
In this position, the courtesy lamp
comes on gradually:
-

w

hen you unlock the vehicle,
-

w

hen the electronic key is removed from the
reader,
-
w

hen opening a

door,
-

w

hen the remote control locking button is
activated, in order to locate your vehicle.
It will only be possible to switch on the door
mirror spotlamps if the courtesy lamp is in this
position.
It switches off gradually:
-

w

hen the vehicle is locked,
-

w

hen the ignition is switched on,
-

3

0

seconds after the last door is closed. Permanently off.
Permanent lighting.
Storage behind the 3rd row seats
F Make sure that the 3rd row seats are folded.
F
F
old the first two concertina boards.
F

P

osition the roller in the space located
above the armrest, side by side, tilting it
s l i g ht l y.
F

S

lide the roller to the stop position, until it
reaches the notches arranged at the back of
the boot, with the two hinges facing down.
F

U

nfold the third row seats.
The folded concertina boards can be placed in
the horizontal or upright position. 1.
Front courtesy lamp
2. Front map reading lamps
3. Rear courtesy lamp
4. Rear map reading lamps
3
Ease of use and comfort

113
"Forward facing "
When a "for ward facing" child seat is installed
on a
rear passenger seat , move the vehicle's
front seat for ward and straighten the backrest
so that the legs of the child in the "for ward
facing" child seat do not touch the vehicle's
front seat.
3rd row seats
Child seat at the front
" Rearward facing"
When a "rear ward facing" child seat is installed
on the front passenger seat , adjust the
vehicle's seat to the intermediate longitudinal
and lowest position, with the backrest
straightened. Then pull the booster/height
adjuster control 11
times.
The front passenger airbag must be
deactivated. Otherwise, the child risks
being seriously injured or killed in case
of airbag deployment .
"Forward facing "
When a "for ward facing" child seat is
installed on the front passenger seat ,
adjust the vehicle's seat to the intermediate
longitudinal and lowest position, with the
backrest straightened. Then pull the booster/
height adjuster control 11
times. Leave the
passenger's airbag active. Passenger seat adjusted into the intermediate
longitudinal and lowest position, then the
booster/height adjuster control pulled 11
times.
When a

child seat is installed on a

rear
passenger seat in the 3
rd row , move the
seats in the 2nd row for ward and straighten the
backrest so that the child seat and the child's
legs do not touch the seat in the 2
nd row.
A child seat with a

support leg must never be
installed on a r ear passenger seat in the 3rd
row ,
Deactivating the front
passenger airbag
Never install a "rear ward facing" child
r estraint system on a seat protected by an
active front airbag. This could cause the
death of the child or serious injury.
5
Safety