wheel bolts Citroen C4 PICASSO DAG 2008 1.G Owner's Manual

23
4
567
89
1
VI
191
C H A N G I N G A W H E E L
TOOLS
The tools are to be found either in the compartment under the second-row passenger footwells or in the well under the third-row seats (de-pending on equipment).
Switch on your hazard warning lights, ensure that any passengers leave the vehicle and fi nd a safe place to wait away from traffi c (e.g. behind crash barriers or on a grass verge).
Never get underneath the vehicle if it is supported only by the jack ; use a stand.
It is essential not to exceed a speed of 80 km/h (50 mph) on your spare wheel.
Have the original wheel repaired and refi tted as soon as possible.
5- Vehicle jack with handle
6- Removable towing eye
7- Two chocks, provided for chan ging a wheel or for other uses on the vehicle (such as unlocking the electric parking brake)
8- Electric parking brake unlocking 8-device
9- Anti-theft socket.
1- Tool for removing the central trim on alloy wheels
2- Tool for removing the chrome covers on the wheel bolts on alloy wheels
3- Centring guide
4- Tool for removing the wheel bolts

A
1
VI
193
C H A N G I N G A W H E E L
REMOVING A WHEEL
1. Park the vehicle on level, stable and non-slippery ground. Apply the parking brake.
Switch off the ignition, check that the parking brake is applied (message and warning lamp in the instrument panel) and engage fi rst gear or reverse gear depending on the slope (P if an automatic gearbox, D or R if a 6-speed electronic gearbox).
2. Use a chock to secure the vehicle more safely. Place the chock in front of the wheel that is opposite the wheel affected.
3. Detach the trim using the removing tool 4, pulling in the area of the valve.
For vehicles with alloy wheels, insert the trim removing tool 1into the recess in the central trim and lever it off.
For vehicles with alloy wheels that have visible bolts, remove the chromes covers using the tool 2.
Before any operation of this sort, it is advisable to deactivate your pneumatic suspension (see “Pneumatic sus-pension”). When changing a wheel, it is essential to immobil ise the vehicle on ground that is level, stable and non-slippery.
4. Slacken the wheel bolts. For vehicles with alloy wheels, undo the anti-theft bolts using tool 9.
5. Position the jack under the vehicle (see diagrams), at the jacking point A closest to the wheel to be changed.
6. Unwind the jack 5 until its bracket is in contact with the ground. Make sure that the jack is vertical under the jacking point used.
7. Continue to extend the jack so as to raise the vehicle.
8. Undo the wheel bolts and remove the wheel.

194
VI
C H A N G I N G A W H E E L
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use only, when fi tting this it is normal to observe that the wheel bolts do not come to bear directly on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft (see illustration).
When refi tting the original wheel, ensure that the wheel bolt contact surfaces are clean and in good condition.
WHEEL EQUIPPED WITH DEFLATION DETECTION SYSTEM
Such wheels have tyre pressure sensors. It is essential to have re-pairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS (alloy wheels)
Each wheel may be equipped with one anti-theft bolt.
To remove it :
1. Remove the protector that is covering it by means of the tool 2 (for removing the chrome covers on alloy wheels).
2. Use the anti-theft socket 9with the handle.
DIMENSION OF THE SPARE WHEEL
If your spare wheel has dimen-sions different from those of the normal vehicle wheels (identifi ed by a label), it is imperative to use the spare wheel only temporarily, to drive with caution, not to exceed 80 km/h (50 mph) and to have the tyre repaired and the normal wheel refi tted as soon as possible.
Tyre pressures
These are indicated on the label on the front left-hand door pillar (see «Vehicle Identifi cation»).
The wheel bolts are specifi c to each type of wheel.
If new wheels are fi tted, check with your CITROËN dealer that the wheel bolts are compatible with the new wheels.
Note : take care to note down the code number on the head of the anti-theft bolt socket. This will enable you to obtain a replacement anti-theft socket from a CITROËN dealership.theft bolt socket. This will enable you This will
REFITTING A WHEEL
1. Position the wheel with the aid of the centring guide 3.
2. Do up the 3 bolts by hand, then remove the centring guide 3. Position the 4th bolt.
3. Pre-tighten the wheel bolts, using the wheelbrace 4.
4. Retract the jack 5 and disen-gage it.
5. Tighten the wheel bolts, using the wheelbrace 4.
6. Ensure that the tyre pressure is correct (see “Vehicle identi-fi cation”).