boot Citroen C4 PICASSO DAG 2010.5 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010.5, Model line: C4 PICASSO DAG, Model: Citroen C4 PICASSO DAG 2010.5 1.GPages: 355, PDF Size: 13.32 MB
Page 4 of 355
7
F A M I L I A R I S A T I O N
This opening gives easy access to the
boot, even if you are parked close to a
wall or to another vehicle.
Opening rear screen
Opening
Press control 2 . The grip 4 is in line
with the rear wiper.
Closing
Lower the rear screen.
89
Press control 1 .
You cannot open the tailgate if the rear
screen is already open.
Lower the tailgate, using one of the
grips 3 , located on the interior tail-
gate trim.
Past the balancing point, allow the
t a i l g a t e t o c l o s e i t s e l f ( d o n o t a s s i s t
i t o r s l o w i t d o w n ) .
Load: 22 kg maximum.
The Modubox is composed of a shop-
p i n g t r o l l e y a n d a fl e x i b l e b a g w h i c h c a n
be used independently of each other
depending on your needs.
110
O P E N I N G
Opening the tailgate
Closing the tailgate Modubox (CITROËN
C4 Picasso)
Page 19 of 355
22
F A M I L I A R I S A T I O N
I N T E R I O R
Folding the seats
From the boot - whilst loading,
for example (CITROËN Grand
C4 Picasso)
SECOND ROW SEATS
From outside
P u l l fi r m l y u p w a r d s o n s t r a p C , as
indicated by the red arrow, to unlock
the seat; keep pulling until the seat
is fully folded.
Slide latch A of the panel down-
wards, to unlock it.
Return the panel to the upright posi-
tion, then slide latch A upwards to
lock it.
Before deploying the rigid panels, check
that the second row seats are in their
fully rear position.
71
H a v i n g fi r s t l y f o l d e d t h e t h i r d - r o w
seats.
Pull on strap D to unlock the re-
q u i r e d s e a t . Repositioning the seats
Return the rigid panels of the second-
r o w s e a t s t o t h e i r i n i t i a l ( u p r i g h t ) p o s i t i o n
a n d l o c k t h e m i n p o s i t i o n ( C I T R O Ë N
G r a n d C 4 P i c a s s o ) .
Raise the backrest and push it back-
wards until it locks in position.
Rigid panel (CITROËN Grand
C4 Picasso)
A rigid panel is attached to each second-
row seat backrest.
Unlocking/Locking the rigid panel
Page 32 of 355
I
36M O N I T O R I N G
Warning lamps
When the engine is running or the vehicle is being driven,
the switching on of one of the following warning lamps indicates
a fault which requires action on the part of the driver.
Any fault resulting in the switching on of a warning lamp must be investigated further by reading the associated message
on the multifunction screen.
If you encounter any problems, do not hesitate to contact a CITROËN dealer.
Warning lamp is on Cause Action/Observations
STOP fi x e d , a s s o c i a t e d
with another
warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer.
Service temporarily.
A minor fault has occurred
f o r w h i c h t h e r e i s n o s p e c i fi c
warning lamp. Identify the fault by reading the message
shown on the screen, such as, for
example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- s a t u r a t i o n o f t h e p a r t i c l e e m i s s i o n fi l t e r (Diesel).
For any other faults, contact a CITROËN
dealer.
fi x e d . A m a j o r f a u l t h a s o c c u r r e d
f o r w h i c h t h e r e i s n o s p e c i fi c
warning lamp. Identify the fault by reading the message
shown on the screen and contact a
CITROËN dealer.
Page 36 of 355
I
40M O N I T O R I N G
Warning lamp is on Cause Action/Observations
Maximum
coolant
temperature fi x e d r e d .
The temperature of the
cooling system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down
before topping up the level, if necessary.
If the problem persists, contact a
CITROËN dealer.
Battery
charge fi x e d . The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...). The warning lamp should go off when the
engine is started.
If it does not switch off, contact a
CITROËN dealer.
Door(s) open fi x e d i f t h e s p e e d
is below 6 mph (10 km/h).
A door, the boot or the rear
screen is still open. Close the door or boot.
fi x e d a n d
accompanied by
an audible signal if the speed is above 6 mph (10 km/h).
+
Seat belts
not fastened/ unfastened fi x e d . The driver and/or the front/
rear passenger has not
fastened or has unfastened
their seat belt.
Pull the strap then insert the tongue in the buckl
e. The illuminated dots represent the passengers
that have not fastened/unfastened their seat belt.
They come on:
- fi x e d f o r 3 0 a b o u t s e c o n d s o n s t a r t i n g
the vehicle,
- fi x e d f r o m 0 t o 1 2 m p h ( 0 t o 2 0 k m / h ) when driving,
- fl a s h i n g a b o v e 1 2 m p h ( 2 0 k m / h ) , accompanied by an audible signal for
about 120 seconds.
Page 71 of 355
III
70
C O M F O R T
SECOND ROW SEATS (C4 PICASSO)
Folding a seat
Each seat can be folded onto the
fl o o r t o e n a b l e y o u t o m o d i f y y o u r
vehicle’s interior space.
P u l l fi r m l y u p w a r d s o n s t r a p C ,
as indicated by the red arrow, to
unlock the seat; keep pulling un-
til the seat is fully folded.
Push the seat backrest gently forwards so that the backrest
folds onto the seat cushion. The
a s s e m b l y l o w e r s o n t o t h e fl o o r . Repositioning a seat
Raise the backrest and push it
rearwards until it locks in position
Always supervise any movements
of seats by children. Panels behind the second row
seats
Panels below the second row seats
provide the bottom of the boot space
with rigidity. They automatically follow
the seat movements (e.g. forwards-
backwards adjustment, folding).
A storage area is available under-
neath the panels.
Page 72 of 355
III
71
C O M F O R T
SECOND ROW REAR SEATS (GRAND C4 PICASSO)
Each seat can be folded onto the
fl o o r t o f o r m a fl a t s u r f a c e , t h u s e n -
abling you to adapt your vehicle’s
interior space.
Folding a seat
From the outside
P u l l fi r m l y u p w a r d s o n s t r a p C ,
as indicated by the red arrow, to
unlock the seat; keep pulling un-
til the seat is fully folded.
Push the seat backrest gently forwards so that the backrest
folds onto the seat cushion. The
a s s e m b l y l o w e r s o n t o t h e fl o o r . From the boot (when loading, for
example)
You can fold the second-row seat(s)
f r o m t h e b o o t , h a v i n g fi r s t f o l d e d t h e
third-row seats.
Pull on the strap D to unlock the
chosen seat, push the backrest
gently forwards.
To prevent any damage to the mechanism, the strap D unclips
under excessive force. Simply
clip it back in place to render the
system operational.
Repositioning a seat
Return the second-row seat rigid
panels to their initial position and
lock them in position.
Raise the backrest and push it
rearwards until it locks in position.
Before moving the third-row seats,
return the second-row rigid panels
to their initial position and lock them
in place.
Never allow children to operate the
seats without supervision. Rigid panel
Each second-row seat backrest has
a rigid panel attached.
This panel enables you:
- to have a continuous load sur-
face in the boot, whatever the
positions of the seats,
- to avoid having objects sliding under the second-row seats.
Unlocking/Locking the rigid
panel
Slide the latch 1 on the panel
downwards, to unlock.
Return the panel to the upright
position, then slide the latch 1
upwards, to lock.
Before positioning the rigid panels,
check that the second-row seats are
in the fully back position.
5 - s e a t e r c o n fi g u r a t i o n s d o n o t h a v e
these rigid panels.
Page 78 of 355
IV
77
A C C E S S
REMOTE CONTROL KEY
System which permits central un-
locking or locking of the vehicle us-
ing the door lock or remotely. It is
also used to locate the vehicle, acti-
vate the guide-me-home lighting and
start the engine, as well as providing
protection against theft.
Unlocking the vehicle
Complete unlocking using the
remote control
Unfolding the key
First press this button to unfold
the key.
Press the open padlock
to unlock the vehicle. Complete unlocking using the
key
Turn the key to the left in the
driver's door lock to unlock the
vehicle.
U n l o c k i n g i s c o n fi r m e d b y r a p i d
fl a s h i n g o f t h e d i r e c t i o n i n d i c a t o r s
for approximately two seconds.
According to version, the door mir-
rors unfold at the same time.
This also triggers the timed switching
on of the welcome lighting, courtesy
lamps and exterior side spot lamps
for approximately thirty seconds.
Selective unlocking using the
remote control
Press the open pad-
lock once to unlock the
driver's door only.
Press the open padlock again to
unlock the other doors and the
boot. According to version, the door mir-
rors unfold at the same time as the
fi r s t u n l o c k i n g a c t i o n .
It also triggers the timed switch-
ing on of the welcome lighting, the
courtesy lamps and the exterior side
spotlamps for approximately thir-
ty seconds.
The complete or selec-
tive unlocking parameter
is set via the multifunc-
t i o n s c r e e n c o n fi g u r a t i o n
menu.
Complete unlocking is activated by
default.
U n l o c k i n g i s c o n fi r m e d b y r a p i d
fl a s h i n g o f t h e d i r e c t i o n i n d i c a t o r s
for approximately two seconds. Selective unlocking is not available
using the key.
Page 79 of 355
IV
78
A C C E S S
Normal locking using the key
Turn the key to the right in the
driver's door lock to lock the
vehicle. To allow long objects to be carried,
the vehicle can be locked from the
inside, using the central locking
control on the dashboard, even if
the tailgate or rear screen is open.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock
itself again automatically after thirty
seconds unless a door is opened.
When closing the windows and/or
panoramic sunroof blind using the
remote control, you must ensure
that no one prevents them from
closing correctly.
The folding and unfolding of the
door mirrors using the remote
control can be deactivated by a
CITROËN dealer. Deadlocking using the remote
control
Press the closed pad-
lock to lock the vehicle
completely or press the
closed padlock for more
than two seconds to
close the windows and
the panoramic sunroof
blind automatically in
addition to locking.
Press the closed padlock again
w i t h i n fi v e s e c o n d s t o d e a d l o c k
the vehicle.
Locking the vehicle
Normal locking using the remote
control
B r i e fl y p r e s s t h e c l o s e d
padlock to lock the ve-
hicle.
Make a long press on the closed
padlock to lock the vehicle and
also close the windows and the
panoramic sunroof blind.
L o c k i n g i s c o n fi r m e d b y fi x e d l i g h t -
ing of the direction indicators for ap-
proximately two seconds.
According to version, the door mir-
rors fold at the same time.
Locking also triggers the timed
switching on of the exterior side
spotlamps and the guide-me-home
lighting, if this is activated. If one of the doors, the rear screen
or the boot is still open, the central
locking does not take place.
Page 88 of 355
IV
83
A C C E S S
ALARM
System which protects and provides
a deterrent against theft and break-
ins. It provides the following types of
monitoring.
- Exterior perimeter
The system checks for opening of
the vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- Interior volumetric
The system checks for any variation
in the volume in the passenger com-
partment.
The alarm is triggered if anyone
breaks a window, enters the pas-
senger compartment or moves in-
side the vehicle.
Self-protection function
The system checks for the putting
out of service of its components.
The alarm is triggered if the battery,
the central control or the wires of
the siren are put out of service or
damaged. Locking the vehicle with full
alarm system
Activation
Switch off the ignition and get out
of the vehicle.
Press the locking button on the
remote control. Deactivation
Press the unlocking button on
the remote control.
The alarm system is deactivated:
the indicator lamp on the button
switches off.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric monitoring.
The monitoring system is active: the
i n d i c a t o r l a m p o n t h e b u t t o n fl a s h e s
once per second.
After the locking button on the re-
mote control is pressed, the exterior
perimeter monitoring is activated
after a delay of 5 seconds and the
interior volumetric monitoring after a
delay of 45 seconds.
For all work on the alarm system,
contact a CITROËN dealer.
Page 89 of 355
IV
84
A C C E S S
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
monitoring to avoid unwanted trig-
gering of the alarm in certain cases
such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle, To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Deactivation of the interior
volumetric monitoring
Switch off the ignition.
Within ten seconds, press the
button until the indicator lamp is
lit continuously.
Get out of the vehicle.
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring
alone is activated: the indicator lamp
o n t h e b u t t o n fl a s h e s o n c e p e r s e c o n d .
Triggering of the alarm
The monitoring functions remain
active until the alarm has been trig-
gered eleven times in succession.
When the vehicle is unlocked using
t h e r e m o t e c o n t r o l , r a p i d fl a s h i n g
of the indicator lamp on the button
informs you that the alarm was trig-
gered during your absence. When
the ignition is switched on, this
fl a s h i n g s t o p s i m m e d i a t e l y . Failure of the remote control
To deactivate the monitoring func-
tions:
Locking the vehicle without
activating the alarm
Malfunction
Automatic activation *
Lock or deadlock the vehicle us-
ing the key in the driver's door
lock.
W h e n t h e i g n i t i o n i s s w i t c h e d o n , fi x e d
lighting of the indicator lamp on the
button indicates a malfunction of the
system.
Have it checked by a CITROËN dealer.
2 minutes after the last door or the
boot is closed, the system is activat-
ed automatically.
To avoid triggering the alarm on
e n t e r i n g t h e v e h i c l e , fi r s t p r e s s
the unlocking button on the re-
mote control.
Unlock the vehicle using the key
in the driver's door lock.
Open the door; the alarm is trig-
gered.
Switch on the ignition; the alarm
stops. The indicator lamp on the
button switches off.
This is indicated by sounding of the
s i r e n a n d fl a s h i n g o f t h e d i r e c t i o n i n -
dicators for thirty seconds.
Reactivation of the interior
volumetric monitoring
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp on the button
a g a i n fl a s h e s o n c e p e r s e c o n d .
* According to country.