jacking Citroen C4 RHD 2015 2.G Owner's Manual

1111
192 
Ensure that the  jack  is  stable.  If  the
 ground  is  slippery  or  loose,  
the

 
jack
 
may
 
slip
 
or
 
drop
 
-
 
Risk
 
of

  injury!
Removing a wheel
Parking the vehicle
Immobilise  
the
 
vehicle
 
where
 
it
 
does

 
not
 
block
 
traffic:
 
the
 
ground
 
must

 
be
 
level,
 
stable
 
and
 
non-
slippery

  ground.
Apply
 
the
 
parking
 
brake
 
unless
 
it has

 
been
 
programmed
 
to
 
auto
-
matic
 
mode,
 
switch
 
of
f  
the
 
ignition and

 
engage
 
first
 
gear*
 
to
 
lock
 
the wheels.
Check

 
that
 
the
 
braking
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
are

  on   (not   flashing).
The
 
occupants
 
must
 
get
 
out
 
of
 
the

 
vehicle
 
and
 
wait
 
where
 
they
 
are

  safe.
If
 
necessary
,  
place
 
a
 
chock
 
un
-
der
 
the
 
wheel
 
diagonally
 
oppo
-
site
  the   wheel   to   be   changed.
Never
 
go
 
underneath
 
a
 
vehicle
 
raised

 
using
 
a
 
jack;
 
use
 
an
 
axle
 
stand. *

position R
 
for
 
an
 
electronic
 
gearbox;
 
P

 for   an   automatic   gearbox.
List of operations
F  
Extend
 
the
 
jack
 
2
 
until
 
its
 
head
 
comes

 
into
 
contact
 
with
 
the
 
jacking
 
point A

or B  
used;
 
the
 
contact
 
sur
-
face A or B
 
on
 
the
 
vehicle
 
must
 
be
 
engaged

 
with
 
the
 
central
 
part
 
of
 
the
 
head

  of   the   jack.
F
 
Raise
 
the
 
vehicle
 
until
 
there
 
is
 
suffi
-
cient
 
space
 
between
 
the
 
wheel
 
and
 
the

 
ground
 
to
 
admit
 
the
 
spare
 
(not
 
punctured)

  wheel   easily.
F
 Remove  the  chromed  bolt  cover  from
 each  of  the  bolts  using  the  
tool

3   (according   to   equipment).
F
 
Fit
 
the
 
security
 
socket
 
4 on the wheel

-
brace 1
 

to   slacken   the   security   bolt.
F
 
Slacken
 
the
 
other
 
bolts
 
using
 
the
 
wheelbrace

1   only.
F
 
Place
 
the
 
foot
 
of
 
the
 
jack
 
2
on the
ground
 
and
 
ensure
 
that
 
it
 
is
 
directly
 
below the front

A or rear B  
jacking
 
point

 
provided
 
on
 
the
 
underbody
,  
whichever is closest to the wheel to
be

  changed.
PRACTICAL INFORMATION

1111
193 
Fitting a steel or "space-
saver" spare wheel
If 
your
 
vehicle
 
is
 
fitted
 
with
 
al
-
loy
 
wheels,
 
when
 
tightening
 
the
 
bolts

 
on
 
fitting
 
it
 
is
 
normal
 
to
 
notice

 
that
 
the
 
washers
 
do
 
not
 
come

 
into
 
contact
 
with
 
the
 
steel
 
or

 
"space-saver"
 
spare
 
wheel.
 
The

 
wheel
 
is
 
secured
 
by
 
the
 
conical

  contact   of   each   bolt.List of operations
F
 Remove
 the
 bolts
 and
 store
 them
 in
 a
 
clean
 
place.
F
 
Remove

 
the
 
wheel. F
 Put   the   wheel   in   place   on   the   hub.
F  Screw  in  the  bolts  by  hand  to  the  
stop.
F

 
Pre-tighten
 
the
 
security
 
bolt
 
using
 
the wheelbrace

1  
fitted
 
with
 
the
 
se
-
curity
  socket   4.
F
 
Pre-tighten
 
the
 
other
 
bolts
 
using
 
the
 
wheelbrace

1   only.
Fitting a wheel
Take care to  position  the  jack  only at
 one  of  the  jacking  points  A
or B
under
 
the
 
vehicle,
 
ensuring
 
that the

 
head
 
of
 
the
 
jack
 
is
 
centred under

 
the
 
contact
 
surface
 
of
 
the vehicle.

 
Otherwise,
 
there
 
is
 
a
 
risk of

 
damage
 
to
 
the
 
vehicle
 
and/or the

  jack   dropping   -   Risk   of   injury!
PRACTICAL INFORMATION