bonnet Citroen C5 2000 (DC/DE) / 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 153
INJECTION
Component (diagr.) Supplier Reference Observations
88 way connector. Flash eprom type sequential
Diesel injection ECU1BOSCHEDC 15C2 injection (reprogrammable eprom). Installed in the
ECU compartment.
Engine speed sensor2ELECTRIFIL
Camshaft position sensor3ELECTRIFIL Air gap value : 1,2 mm.
Coolant temperature sensor7ELECTRIFIL 962859028A Fixed on the coolant housing.
Accelerator pedal sensor8PHILIPS
Vehicle speed sensor9EATON On the gearbox.
Brake pedal switch10aOpen at rest.
10bClosed at rest.
Clutch pedal switch11
Atmospheric pressure sensor12BOSCHIntegrated in the injection ECU.
Battery
13FULMEN058426 – 12 Volt
400 ampsUnder the bonnet.
Injection double relay14BITRON 240 10915 way black connector. Installed in the ECU
compartment.
FIRST3 way black connector. Installed in the front RH
Inertia switch30INERTIA Type 505wheelarch, fixed on the suspension mounting.
SWITCHManual rearming in the event of the cut-out system
being activated.
FEATURES OF BOSCH HDi DIRECT INJECTION SYSTEM
Electrical circuit

Downloaded from www.Manualslib.com manuals search engine 183
CLUTCH
GEARBOX
DRIVESHAFTS
BE4/5 GEARBOX CONTROLS
Engines : 6FZ - RFN - RLZ - RHY
Adjustments (continued)
Under the bonnet.
- Remove the air filter assembly.
- Unlock the gear engagement cable ball-joint(b).
- Unlock the gear selection cable ball-joint(c).
- Make sure the gear levers (engagement and selection)are in neutral position.
- Lock the cable lengths with the ball-joint locking keys.
- Remove the tool [1].
Checks.
- Remove the tool[1].
- Check that all the gears engage without «tightness».
- Check that the gear lever moves identically forwards and backwards and to right and left. If not :
- Repeat the adjustment.
- Refit the console and the air filter assembly.
B2CP3E8CB2CP3E9C

Downloaded from www.Manualslib.com manuals search engine 192
CLUTCH
GEARBOX
DRIVESHAFTS
ML/5 GEARBOX CONTROLS
Engines : XFX – RHZ – 4HX
Adjustments (continued)
Under the bonnet.
- Remove the air filter assembly.
- Unlock the gear engagement and selection cable ball-joint(b).
- Make sure the gear levers (engagement and selection) are in neutral position.
- Lock the cable lengths with the ball-joint locking keys.
- Remove the tool [1].
Checks.
- Remove the tool [1].
- Check that all the gears engage without «tightness».
- Check that the gear lever moves identically forwards and backwards and to right and left. If not :
- Repeat the adjustment.
- Refit the console and the air filter assembly.
B2CP3EBC

Downloaded from www.Manualslib.com manuals search engine C5HP16EC
SPECIAL FEATURES : AIR CONDITIONING SYSTEM (R 134.a)
Condenser with integral reservoir (continued)
Removing the reservoir (6) from the base (8).
WARNING :This operation requires the greatest care, the base(8)should be kept clean prior to fitting
the new reservoir.
- Remove the reservoir (6) and the protection skirt(7), avoiding WITHOUT F
AILany contact or collision
with other items under the bonnet(Risk of impurities entering the base (8)).
- Check before refitting the reservoir (6)that the base(8)is clean.
(If it is not, clean in and around the base(8)with a paper cloth.)
Preparing the new dryer reservoir
- Remove the black plastic protection cap from the reservoir neck (6), leaving in place the green protec-
tion at the other end, in order to keep the new reservoir (6) sealed when mounting it in the base(8)of
the condenser.
- Use the grease sachet in the replacement kit, to lubricate the threads of the reservoir.
- Use the oil sachet in the replacement kit, to lubricate the two O-ring seals of the reservoir (6).
- Position the reservoir(6), with its new protection skirt (7)from the replacement kit, and engage the
threads of the reservoir (6) in the base (8).
- Check that the downward edge of the skirt (7), covers the base(8) all around it.
AIR
CONDITIONING
248