brake fluid Citroen C5 2000 (DC/DE) / 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2000, Model line: C5, Model: Citroen C5 2000 (DC/DE) / 1.GPages: 259, PDF Size: 2.29 MB
Page 34 of 259
Downloaded from www.Manualslib.com manuals search engine GENERAL
31
Liquide de refroidissement moteur
LUBRICANTS – TOTAL recommended oils
PacksCITROEN reference
GLYSANTIN G 33 REVCOGEL 2000
CITROEN Fluid 2 litres9979 70 9979 72
All countries
Protection : - 35°C 5 litres9979 71 9979 73
20 litres9979 76 9979 74
210 litres9979 77 9979 75
Synthetic brake fluid
Packs CITROEN reference
All countriesCITROEN Fluid0.5 litre9979 05
1 litre9979 06
5 litres9979 07
CITROEN hydraulic circuit fluid
Orange-coloured synthetic fluid, for HYDRACTIVE 3 suspension and for steering
TOTAL LDS FLUIDPacks CITROEN reference
All countries 1 litre9979.69
Hydraulic circuit rinsing fluid – green colour
TOTAL HYDRAURINCAGE
Page 146 of 259
Downloaded from www.Manualslib.com manuals search engine FEATURES OF MULTIPOINT INJECTION SYSTEM
Summary
1)Accelerator pedal position sensor
(2)Denox catalyser downstream oxygen sensor
(3)Denox catalyser
(4)Downstream exhaust gas temperature sensor
(5)3-function precatalyser
(6)Precatalyser upstream oxygen sensor
(7) Upstream exhaust gas temperature sensor
(8)Petrol pressure regulator
(9)Petrol high pressure pump
(10)Knock sensor
(11) EGR electrovalve
(12)Canister purge electrovalve
(13)Motorised butterfly housing
(14)Canister reservoir
(15)Fuel pump and tank assembly
(16) Fuel tank
(17)Inlet air temperature sensor
(18) Inlet air pressure sensor(19)Engine coolant temperature sensor
(20) Sparking plug
(21) Ignition coil block
(22) High pressure injector
(23) Engine oil temperature sensor
(24)Engine speed sensor
(25)Inlet camshaft dephaser electrovalve
(26) Camshaft position sensor
(27)Petrol high pressure sensor
(28) Power steering pressure sensor
(29) Aircon fluid pressure sensor
(30)Cooling fan unit
(31)ABS block
(32)Clutch pedal sensor
(33)Brake pedal sensor
(34)Air conditioning ECU
(35) Engine management ECU
(36)Built-in systems interface BSI
(37)Rev counter
(38) Coded immobiliser
(39)Vehicle cruise control
(40) Diagnostic connector
B1HP1C6P
143
INJECTION
Page 229 of 259
Downloaded from www.Manualslib.com manuals search engine BRAKE SPECIFICATIONS
Braking circuit diagram
(a) Hydraulic circuit.
(b) Electrical circuit.
(1)Master cylinder in tandem.
(2) Braking servo.
(3) Brake caliper.
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles).
(5) Wheel sensor.
(6) Brake fluid level sensor.
(7)Hydraulic block plus ECU.
(8) Stoplamp switch.
(9)Instrument panel.
(10) Diagnostic socket.
(11) Built-in systems interface (BSI).
B3GP02HP
BRAKES
226
Page 233 of 259
Downloaded from www.Manualslib.com manuals search engine B3FP139CB3FP13AC
BLEEDING AND FILLING THE BRAKING SYSTEM
Tools.
[1] Generic bleeding apparatus: "LURO" or similar.
[2] PROXIA station: 4165-T.
[3] LEXIA station: 4171-T.
Bleeding, filling.
Draining the brake fluid reservoir.
- Drain the brake fluid reservoir (1) to the maximum (if necessary, use a clean syringe).
- Disconnect the connector (3).
- Uncouple the pipe (2).
- Remove the reservoir (1) by separating the lugs «a»from the shaft (4).
- Empty the brake fluid reservoir(1).
- Clean the brake fluid reservoir (1).
Remove :
- The brake fluid reservoir (1).
- The shaft (4).
- Couple the pipe(2).
- Reconnect the connector(3).
BRAKES
230
Page 234 of 259
Downloaded from www.Manualslib.com manuals search engine B3FP13BCAB3FP13CC
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
Filling the braking system.
WARNING : Use only those hydraulic fluids that are approved and recommended.
- Fill the brake fluid reservoir (1).
Bleeding the braking system.
WARNING: During the bleeding operation, take care to maintain the level of brake fluid in the reser-
voir and to top it up, using only brake fluid that is clean and clear.
Bleeding the primary circuit.
WARNING: The ABS should not be active during the bleeding operation.
- Front brake caliper: Bleed screw(5).
- Rear brake caliper: Bleed screw (6).
- Bleed each wheel cylinder, proceeding in the following order :
Front LH wheel.
Front RH wheel.
Rear LH wheel.
Rear RH wheel.BRAKES
231
Page 235 of 259
Downloaded from www.Manualslib.com manuals search engine B3FP13DC
BRAKES
232
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
With the bleeding apparatus
- Connect the bleeding apparatus [1] on the brake fluid reservoir (1).
- Adjust the apparatus pressure to 2 Bars.
For each circuit :
- Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
- Open the bleed screw, wait until the fluid is flowing out without air bubbles.
- Close the bleed screw.
- Remove the bleeding apparatus [1].
- Check the brake fluid level(Should be between «DANGER» level and«MAXI» level).
- Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE : Two operators are necessary.
For each circuit :
- Apply the brake pedal to place the circuit under pressure.
- Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
- Open the bleed screw, wait until the fluid is flowing out without air bubbles.
- Close the bleed screw.
- Remove the tool [1].
NOTE : Recommence the process a second time if that is necessary.
- Check the brake fluid level, (Should be between «DANGER»level and «MAXI»level).
- Fill if necessary with the approved and recommended synthetic brake fluid.
Page 236 of 259
Downloaded from www.Manualslib.com manuals search engine 233
BRAKES
BLEEDING AND FILLING THE BRAKING SYSTEM
Bleeding, filling (continued).
Bleeding the secondary circuit.
NOTE : The bleeding apparatus is connected on the brake reservoir.
- Use LEXIAorPROXIAdiagnostic tools.
Select the menu corresponding to the vehicle :
- ABS menu.
- ESP menu.
- Follow the instructions on the diagnostic tool.
- At the end of the bleeding process, check and top up, if necessary, the brake fluid level.
- Check that the brake pedal travel has not been lengthened, otherwise repeat the bleeding procedure.
- Remove the tools.