ignition Citroen C5 2000 (DC/DE) / 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine PRESENTATION
THIS HANDBOOK summarises the specifications, adjustments, checks and special features of theCITROEN C5.
The handbook is divided into the following sections representing the main functions :
GENERAL - ENGINE - INJECTION - IGNITION - CLUTCH - GEARBOX - DRIVESHAFTS - AXLES - SUSPENSION - STEERING - BRAKES - HYDRAULICS -
ELECTRICAL - AIR CONDITIONING.

Downloaded from www.Manualslib.com manuals search engine INJECTION
Idling - antipollution 111
Petrol injection 112
Emission standards 113 - 119
Prohibited operations : HDi 120 - 121
Safety requirements : HDi 122 - 123
Checking the fuel supply circuit 124 - 125
Checking the air supply circuit 126 - 130
Exhaust gas recycling 131 - 134
Checking turbo pressure 135 - 138
Features of injection systems 139 - 168
IGNITION
Sparking plugs 169
CLUTCH-GEARBOX
Speedometers 170
Clutch specifications 171 - 172
Gearbox and tyre specifications 173 - 174
BE4/5 gearbox controls 175 - 183
ML/5 gearbox controls 184 - 192
AL4-4HP20 gearbox controls 193 - 203
Driveshafts 204
AXLES-SUSPENSION
Wheels and tyres 205 - 211
Axle geometry 212 - 214
Front and rear axle 215 - 216Suspension 217 - 220
Steering specifications 221 - 222
BRAKES
Brake specifications 223 - 228
Handbrake adjustment 229
Bleeding and filling braking system 230 - 233
HYDRAULICS
Specifications 234 - 237
Suspension spheres 238 - 240
ELECTRICAL
Starter motors 241
Alternators 242
Charging circuit 243
AIR CONDITIONING
Quantities in R 134a aircon system 244
Special features 245
Pollen filter 246
Dryer cartridge 247 - 249
Checking oil level 250 - 251
Checking pressures 252
Air conditioning : 6FN-RFN-RLZ 253
Air conditioning circuit : XFX 254
Air conditioning circuit : RHY-RHZ 255
Air conditioning circuit : 4HX 256
INDEX
GENERAL
Identification of vehicles 1 - 4
General : Dimensions 5 - 6
Weight specifications 7 - 8
Towing specifications 9 - 10
Lifting / supporting the vehicle 11 - 14
Capacities 15 - 18
Lubricants 19 - 32
ENGINES
Engine specifications 34 - 58
Cylinder head marking / tightening
6FZ-RFN-RLZ 38
XFX 51 - 52
RHY-RLZ 55 - 56
4HX 57 - 58
Auxiliaries drive belt 59 - 68
Checking and setting valve timing 69 - 90
Power unit suspension 91 - 95
Exhaust system 96 - 100
Cooling system 101 - 107
Checking oil pressures 108
Oil filter 109
Filling and bleeding engine coolant 110

Downloaded from www.Manualslib.com manuals search engine GENERAL
GENERAL SPECIFICATION : TOWING THE VEHICLE
Vehicle towing : Precautions to be taken
4 HP 20 automatic gearbox. AL4 automatic gearbox.
Towing.
In the event of impossibility to raise the front of the vehicle :
It is ESSENTIALto place the selection lever in position«N».
Do not add oil.
Do not exceed a speed of 30 mphover a distance of 30 miles.
Moving the vehicle.
Never be towed with the ignition switched off.
Never attempt to push-start the vehicle. (Impossible with an automatic gearbox).
Note : The automatic gearbox is only lubricated when the engine is running.Towing.
In the event of impossibility to raise the front of the vehicle :
It is ESSENTIALto place the selection lever in position «N».
Do not add oil.
Do not exceed a speed of 45 mph over a distance of 60 miles.
10

Downloaded from www.Manualslib.com manuals search engine ENGINE
45
Engine : XFX
SPECIAL FEATURES : TIGHTENING TORQUES ( m.daN)
(1) Pencil type ignition coil 0.8 ± 0.3.
(2) Valve cover
- Pre-tightening0.5 ± 0.1
- Tightening1 ± 0.1
(3) Camshaft bearing cap cover
- Pre-tightening0.2 ± 0.1
- Tightening1 ± 0.1
(4) Cylinder head
- Pre-tightening2 ± 0.2
- UntighteningYES
- Tightening1.5 ± 0.2
- Angular tightening225°
B1BP27DP

Downloaded from www.Manualslib.com manuals search engine ENGINE
75
CHECKING AND SETTING THE VALVE TIMING
Engine : XFX
Checking the valve timing setting (continued).
- Peg the crankshaft, using tool[1].
- Check that the tool [2]engages without effort in the cylinder heads at the camshaft pulleys.
- Remove the tools [1] and [2].
Refit :
- The lower timing cover(13).
- The upper timing covers (9)and(10).
- The crankshaft pulley (12).
- The roller / dynamic tensioner assembly (11).
- The power steering pulley.
- Complete the refitting of components.
- Initialise the ignition injection ECU.
B1EP15UDB1EP08TC

Downloaded from www.Manualslib.com manuals search engine 124
INJECTION
CHECKS : LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines : RHY - RHZ - 4HX
Engines : RHY - RHZ
Engine : 4HX
TOOLS
[1] Ø 10 mmlow pressure connector: 4215-T.
[2] Ø 8 mmlow pressure connector: 4218 -T.
[3] Pressure gauge for testing boost pressure : 4073-T Tool kit 4073-T
[4] Extension: 4251-T.
Connect the tool[1]Between the booster pump and the fuel filter (white mark at "a" on the
fuel supply pipe).
Connect the tool[2]downstream of the diesel injectors, Between the high pressure fuel
pump and the fuel filter(green mark at "b" on the fuel return pipe).
WARNING : Any check of pressure downstream of the fuel filter is PROHIBITED.
NOTE : To check the pressures while the vehicle is being driven, insert tool[4] Between
tool[3] and tools[1] et[2].
Checks on pressure : static.
- Switch on ignition
- For 3 seconds(normal functioning):
- Fuel supply pressure shown by the pressure gauge [3] = 2.6 ± 0.4 Bar.
- Fuel return pressure shown by the pressure gauge [3] = 0.6 ± 0.4 Bar.
B1BP20JDB1BP27BD

Downloaded from www.Manualslib.com manuals search engine FEATURES OF MULTIPOINT INJECTION SYSTEM
Summary
(1) Air pump
(2) Power steering pressure sensor
(3) Engine management ECU
(4) Canister purge electrovalve
(5)Butterfly housing
(6)Idle regulation stepper motor
(7) Inlet air temperature sensor
(8)Inlet housing heater element
(9)Butterfly potentiometer
(10)Automatic gearbox (Option)
(11)Built-in systems interface
(12) Transponder
(13)Diagnostic connector
(14) Ignition injection test warning lamp
(15)Battery
(16)Immobiliser unit
(17) Air conditioning
(18) Instrument panel
(19)Fuel tank
(20)Fuel pump, gauge and filter assembly(21)Canister reservoir
(22) Downstream oxygen sensor
(23)Upstream oxygen sensor
(24)Air inlet valve
(25)EGR electrovalve
(26)Camshaft position sensor
(27) Ignition coil
(28)Sparking plug
(29) Injector supply rail
(30)Injectors
(31) Air inlet pressure sensor
(32) Engine coolant temperature sensor
(33) Engine speed sensor
(34)Cooling fan unit
(35) Knock sensor
B1HP1C5P
139
INJECTION

Downloaded from www.Manualslib.com manuals search engine 141
INJECTION
FEATURES OF MULTIPOINT INJECTION SYSTEM
Electrical circuit
(diagr.) Component Supplier Reference Observations
3
26
35
32
33
2
28
27Engine management ECU
with «FRIC»
Camshaft position sensor
Knock sensor
Engine coolant temperature sensor
Engine speed sensor
Power steering pressure sensor
Sparking plug
Ignition coilSAGEM
MAGNETI
MARELLIS2000
MM 48.P2
(1)
144323
F 207 326
257 603 2A
14 43 32
402 244 03
14 43 27
280 291
RFN52HZ
FR8ME
BBC2.2NDE
2 526 118 ELECTRIFIL
SIEMENS
SAGEM (1)
ELECTRIFIL
DAV
ELECTRIFIL
BITRON
(1)= EngineRFN
Ignition circuit
SAGEM
BOSCH
SAGEM
«Flash» eprom (reprogrammable eprom), sequential injection,
112 way connector.
3 way grey connector, fixed on the cylinder head
2 way black connector, fixed on the front part of the engine
block, tightening torque 2 ± 0.5 m.daN.
2 way green connector, fixed on the coolant outlet housing,
tightening torque 1.8 ± 0.1 m.daN.
2 way black connector, fixed on the clutch casing.
2 way blue connector, fixed on the power steering high pressure
pump outlet tube, tightening torque 2 ± 0.2 m.daN.
Electrode gap = 1mm.
Tightening torque 2.5 ± 0.2 m.daN.
4 way black connector.

Downloaded from www.Manualslib.com manuals search engine FEATURES OF MULTIPOINT INJECTION SYSTEM
Summary
1)Accelerator pedal position sensor
(2)Denox catalyser downstream oxygen sensor
(3)Denox catalyser
(4)Downstream exhaust gas temperature sensor
(5)3-function precatalyser
(6)Precatalyser upstream oxygen sensor
(7) Upstream exhaust gas temperature sensor
(8)Petrol pressure regulator
(9)Petrol high pressure pump
(10)Knock sensor
(11) EGR electrovalve
(12)Canister purge electrovalve
(13)Motorised butterfly housing
(14)Canister reservoir
(15)Fuel pump and tank assembly
(16) Fuel tank
(17)Inlet air temperature sensor
(18) Inlet air pressure sensor(19)Engine coolant temperature sensor
(20) Sparking plug
(21) Ignition coil block
(22) High pressure injector
(23) Engine oil temperature sensor
(24)Engine speed sensor
(25)Inlet camshaft dephaser electrovalve
(26) Camshaft position sensor
(27)Petrol high pressure sensor
(28) Power steering pressure sensor
(29) Aircon fluid pressure sensor
(30)Cooling fan unit
(31)ABS block
(32)Clutch pedal sensor
(33)Brake pedal sensor
(34)Air conditioning ECU
(35) Engine management ECU
(36)Built-in systems interface BSI
(37)Rev counter
(38) Coded immobiliser
(39)Vehicle cruise control
(40) Diagnostic connector
B1HP1C6P
143
INJECTION

Downloaded from www.Manualslib.com manuals search engine 146
INJECTION
FEATURES OF MULTIPOINT INJECTION SYSTEM
Ignition circuit
(diagr.) Component Supplier Reference Observations
20Sparking plug
21Ignition coil block
12EGR electrovalve
4 and 7Exhaust gas temperature
sensor
6Precatalyser upstream proportional
oxygen sensor
2Catalytic converter downstream
oxygen sensorElectrode gap = 1 mm.
Tighten to 2,5 ± 0,2 m.daN.
6 way black connector.
6 way grey connector, installed on the cylinder head.
2 way brown connector, length of wire : 250 mm.
Tighten to 4,5 ± 0,4 m.daN.
6 way black connector, length of wire : 250 mm.
Tighten to 4,5 ± 0,4 m.daN.
4 way blue connector. BOSCH
BNA - R13-318
BBC 4.1 HP
2580105A
TS-200
LZA-A06-U1
OZA 538-PG1 DELPHI
SAGEM
HERAEUS
NGKExhaust system