ECU Citroen C5 2008.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5, Model: Citroen C5 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.9 MB
Page 6 of 306
27
1
I N S T R U M E N T S a n d C O N T R O L S
Return to the main
instrument panel screen
display
Successive rotations of the left-hand
thumb wheel on the steering wheel
allow you to return to the main instru-
ment panel screen display (vehicle
speed), via the navigation informa-
tion screen, then the screen display-
ing only the total mileage and the trip
mileage (bottom of screen).
Display of navigation
information on instrument
panel screen
You can display navigation informa-
tion on the instrument panel screen
by rotating the left-hand thumb
wheel on the steering wheel. Log of alerts
This function allows you to display
the log of alerts.
Press on button A .
The following messages appear
consecutively on the instrument
panel screen:
- Tyre pressure check.
- Maintenance indicator reminder.
- Display of message alerts.
- Oil level check.
Page 7 of 306
27
1
I N S T R U M E N T S a n d C O N T R O L S
Return to the main
instrument panel screen
display
Successive rotations of the left-hand
thumb wheel on the steering wheel
allow you to return to the main instru-
ment panel screen display (vehicle
speed), via the navigation informa-
tion screen, then the screen display-
ing only the total mileage and the trip
mileage (bottom of screen).
Display of navigation
information on instrument
panel screen
You can display navigation informa-
tion on the instrument panel screen
by rotating the left-hand thumb
wheel on the steering wheel. Log of alerts
This function allows you to display
the log of alerts.
Press on button A .
The following messages appear
consecutively on the instrument
panel screen:
- Tyre pressure check.
- Maintenance indicator reminder.
- Display of message alerts.
- Oil level check.
Page 41 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
s e t t i n g s o f t h e d r i v e r ' s s e a t , e x t e r i o r
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
A d j u s t y o u r s e a t a n d y o u r e x t e -
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard in- dicating that the settings have
been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it
upwards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to
remain in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 42 of 306
59
3
C O M F O R T
Storing driving positions
System which takes into account the
s e t t i n g s o f t h e d r i v e r ' s s e a t , e x t e r i o r
mirrors and air conditioning. It ena-
bles you to store up to two positions
using the buttons on the side of the
driver's seat. Storing a position
Using buttons M/1/2
Switch on the ignition.
A d j u s t y o u r s e a t a n d y o u r e x t e -
rior mirrors.
Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard in- dicating that the settings have
been stored.
Storing a new position cancels the
previous position.
Recalling a stored position
Ignition on or engine running
B r i e fl y p r e s s b u t t o n 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery. For your safety, avoid storing a
driving position while driving.
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions;
- high, position for use,
- low, storage position.
To raise a head restraint, pull it
upwards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
T o r e fi t i t , e n g a g e t h e h e a d r e s t r a i n t
rods in the holes taking care to
remain in the centreline of the seat
back.
Never drive with the head restraints
removed, they must be in place
and correctly adjusted.
Page 43 of 306
60
3
C O M F O R T
REAR SEATS
Bench seat, the left-hand (2/3) or
right-hand (1/3) section of which
can be folded to adapt the boot load
space.
Removing the seat cushion
Move the corresponding front
seat forwards if necessary.
Raise the front of the seat cushion 1 .
Tilt the seat cushion 1 fully against
the front seat.
Remove the seat cushion 1 from
i t s fi x i n g s b y p u l l i n g u p w a r d s . Refitting the seat cushion
Position the seat cushion 1 verti-
c a l l y i n i t s fi x i n g s .
Fold down the seat cushion 1 .
Press on the seat cushion to se-
cure it.
Folding the seat
In order to fold a rear seat without
any risk of damage, always start
with the seat cushion, never with
the seat back:
move the corresponding front
seat forwards if necessary,
raise the front of the seat cush-
ion 1 ,
tilt the seat cushion 1 fully against
the front seat,
check that the seat belt is posi-
tioned correctly on the side of
the seat back,
lower or remove the head restraints
if necessary,
pull the control 3 forwards to re-
lease the seat back 2 ,
tilt the seat back 2 .
The seat cushion 1 can be removed
to increase the loading volume. Returning the seat back to its
original position
When returning the rear seat to its
original position:
put the seat back 2 in the upright
position and secure it,
fold the seat cushion 1 ,
r e fi t t h e h e a d r e s t r a i n t s o r p u t
them back in place.
When returning the rear seat to its
original position, take care not to trap
the seat belts and ensure that their
buckles are positioned correctly.
The red indicator on the control 3
should no longer be visible; if it is,
push the seat fully back.
Page 94 of 306
98
6
L A Y O U T
BOOT LAYOUT (SALOON)
1. Battery for vehicles with V6 HDi
engine.
2. Pull strap (spare wheel storage).
3. Boot lamp.
4. 6 CD changer. Luggage securing rings
Use the 4 securing rings on the
b o o t fl o o r t o s e c u r e y o u r l u g -
gage.
For safety reasons in the event of
sharp braking, you are advised to
place heavy objects as far forward
in the boot as possible.
Page 95 of 306
99
6
L A Y O U T
BOOT LAYOUT (TOURER)
1. Hook
Allows you to hook shopping bags.
2. Torch
To recharge, return it to its stor- age position.
3. Storage net or Battery com-
partment (for vehicles with V6
2.7 HDi engine).
This provides access to the bat- tery.
1. Luggage-cover blind
(see details on following page)
2. Luggage securing rings
Use the 4 stowing rings provided o n t h e b o o t fl o o r t o s e c u r e y o u r
loads.
For safety reasons in the event of sharp braking, you are ad-
vised to place heavy objects as
far forwards as possible.
3. Hooks
These allow a cargo net to be fi t t e d ( s e e d e t a i l s o n f o l l o w i n g
page).
1. Boot lamp
2. 12 V accessories socket
(100 W maximum)
Cigar-lighter type 12 volts sock- et. It is located on the rear right-
hand trim, and is supplied from
the ignition position.
3. Loading
height control
You can change the height of the vehicle in order to make loading
or unloading easier.
4. Hook
Allows you to hook shopping bags.
5. Storage net or 6 CD changer
Page 96 of 306
100
6
L A Y O U T
LUGGAGE COVER (TOURER)
To roll up
Press the handle (PRESS) gently.
The luggage cover rolls up auto-
matically.
The moving part A can be folded
along the rear bench seat backrest.
To remove
Compress the control 1 and lift
the luggage cover on the right
then on the left to remove it.
To install
Position the left-hand end of the
luggage cover roller in its loca-
tion B behind the rear bench
seat.
Compress the roller control 1
and put the roller in place in its
location C on the right.
Release the control to secure
the luggage cover.
Unroll it to its fastening on the
rear pillar. High load retaining net
(Tourer)
Hooked onto the special upper and
l o w e r fi x i n g s , t h i s p e r m i t s u s e o f t h e
entire loading volume up to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1)
when the rear seats are folded.
When positioning the net, check that
the strap loops are visible from the
boot; this will make slackening or
tightening easier.
Page 97 of 306
101
6
L A Y O U T
Installation
fold down the backs of the rear
seats,
position the high load retaining net
roller above the two rails 1 located
behind the rear seats (2/3 bench
seat). The two notches 2 must be
placed above the two rails,
slide the two rails 1 into the
notches 2 and push the roller
(lengthways) from right to left to
secure it,
reposition the rear seat backs. Row 1 Row 2
To use it in row 1:
fold down the
backs of the
rear seats,
open the covers
3 of the corre-
sponding upper
fi x i n g s ,
unroll the high load retaining net
and position one of the ends of
the net's metal bar in the cor-
r e s p o n d i n g fi x i n g c o v e r . C h e c k
that the hook is secured in the
rail located inside the cover 3 ,
pull the high load retaining net's
metal bar to position the other
h o o k i n t h e s e c o n d fi x i n g c o v e r . To use it in row 2:
open the covers
4 of the corre-
sponding upper
fi x i n g s ,
from the rear bench seat, unroll
the high load retaining net, push-
ing it to detach it from the retain-
ing hooks,
position one of the ends of the
net's metal bar in the corre-
s p o n d i n g fi x i n g c o v e r . C h e c k
that the hook is secured in the
rail located inside the cover,
position the other hook in the
s e c o n d fi x i n g c o v e r a n d p u l l t h e
metal bar towards you.
Page 99 of 306
103
C H I L D S A F E T Y
Passenger air bag OFF
CHILD SEATS RECOMMENDED BY CITROËN
CITROËN offers a complete range of recommended child seats which are
secured using a three point seat belt :
Group 0: from birth to 10 kg
Group 0+: from birth to 13 kg
Groups 1, 2 and 3: from 9 to 36 kg
L1
"RÖMER
Baby-Safe Plus"
Installed in the
rearwards-facing position.
L2
"KIDDY Life" The use of
the restraining cushion is
compulsory for
the transportation of young children (from 9 to 18 kg).
Groups 2 and 3: from 15 to 36 kg
L3
"RECARO Start''
L4
"KLIPPAN Optima"
From the age
of 6 years
( a p p r o x i m a t e l y 22 kg),
the booster
is used on its own.