change time Citroen C5 2008.5 (RD/TD) / 2.G Owner's Manual

38
2
M U L T I F U N C T I O N D I S P L A Y S
Adjusting the brightness and
contrast

 Press on A .

 Use C to select the "Brightness -
video adjustment" menu. Confi rm
with a press on C on the steering
wheel or D on the audio equip-
ment.

 Select the confi guration of the
screen using C . Confi rm with a
press on C on the steering wheel
or D on the audio equipment.

 Select the brightness setting.
Confi rm with a press on C on the
steering wheel or D on the audio
equipment.

 Select the inverse or normal dis-
play mode using C then validate
with a press on C on the steering
wheel or D on the audio equip-
ment. To adjust the brightness
select "+" or "-" and save your
setting with a press on C .

 Confi rm with "OK" on the
screen. Adjusting the date and the
time

 Press on A .

 Use C to select the "Adjusting
the date and time" menu, then
confi rm your choice with a press
on C on the steering wheel or D
on the audio equipment.

 Select the screen confi guration
using C . Confi rm with a press on

C on the steering wheel or D on
the audio equipment.

 Select the adjustment for the
date and the time, using B .
Confi rm with a press on C on the
steering wheel or D on the audio
equipment.

 Press C to select the values you
wish to modify. Confi rm your
choice with a press on C on the
steering wheel or D on the audio
equipment.

 Confi rm with "OK" on the
screen. Choosing the units

 Press on A .

 Use C to select the "Choice of
temperature units" menu, then
confi rm your choice with a press
on C on the steering wheel or D
on the audio equipment.

 Using C , select the unit then val-
idate with a press on C on the
steering wheel or D on the audio
equipment.

 Confi rm with "OK" on the
screen.
Selection of the type of
information displayed (Mode)
Successive presses on the end of
the wiper stalk or on the MODE but-
ton on the audio equipment permit
selection of the type of informa-
tion presented on the multifunction
screen (date or radio, CD, MP3 CD,
CD changer).

47
3
C O M F O R T
It controls the temperature, air fl ow
and intake and distributes the ven-
tilation to the windscreen and front
side windows.
Resuming manual control exits from
"Demisting" mode. It must be can-
celled to permit renewal of the air
in the passenger compartment and
demisting.
Once the screen is clear, press-
ing control 1 returns the system to

"AUTO" mode.


Press control 7 , with
the engine running, to
demist the rear screen
and the mirrors. The in-
dicator lamp comes on.
Demisting is switched off automatically
to prevent an excessive consumption
of current and in relation to the exterior
temperature.
It may be stopped by pressing con-
trol 7 again or when the engine is
switched off.
7. Rear demisting - de-icing
The heated rear screen operates in-
dependently of the air conditioning
system.
8. Intake of exterior air/
Recirculation of interior air
This function enables you to isolate
the passenger compartment from
exterior fumes and odours. - When starting with the engine
cold, the fl ow will reach its op-
timum level gradually to pre-
vent an excessive distribution
of cold air.
- When entering the vehicle af- ter it has been parked for a
fairly long period, if the inte-
rior temperature is very differ-
ent from your comfort setting
there is no need to change
the temperature displayed
in order to quickly reach the
level of comfort required. The
system automatically uses its
maximum performance to cor-
rect the difference in tempera-
ture as quickly as possible.
- The water resulting from the air conditioning condensation
is discharged via an open-
ing provided for this purpose;
therefore, a puddle of water
may form underneath the ve-
hicle when stationary.
- In all seasons, if the weather is cool, the air conditioning
is useful as it removes the
humidity from the air and the
condensation. Avoid driving
for prolonged periods with the
air conditioning switched off.
However, demisting resumes when
the engine is switched on again.
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current con-
sumption reduces fuel consumption.

 Press control 8 sever-
al times to set the air
intake mode, the indi-
cator lamp comes on.

It must be cancelled as soon as
possible to permit renewal of the
air in the passenger compartment
and demisting.

110
8
S A F E T Y
DIRECTIONINDICATORS

 Lower the lighting stalk fully
when moving to the left.

 Raise the lighting stalk fully when
moving to the right.
"Motorway" function
System for indicating a change of
lane on a motorway.

 Move the stalk briefl y upwards
or downwards, without going
beyond the resistance point;
the direction indicators will fl ash
3 times.
This function can be used at any
speed, but it is particularly useful
when changing lane on high-speed
roads.
HAZARD WARNING LAMPS
A visual warning by means of the di-
rection indicators to alert other road
users to a vehicle breakdown, towing
or accident.
Automatic lighting of hazard
warning lamps
When braking in an emergency,
depending on the deceleration, the
hazard warning lamps come on.
They will switch off automatically the
fi rst time you accelerate.

 If they do not, press button A to
switch the direction indicators
off. Audible warning to alert other road
users to an imminent danger.
Selection of the left or right direction
indicators to signal a change of direc-
tion of the vehicle.

 Press the button, the direction
indicators fl ash.
They can operate with the ignition
off.
As a safety precaution in a traffi c
jam, switch on the hazard warn-
ing lamps if you are the last in the
queue.
 Press the left or right-hand part
of the fi xed centred controls
steering wheel.
Use the horn moderately and only
in the following cases:
- immediate danger,
- when approaching an area
- where there is no visibility.

146
9
D R I V I N G
Reactivation
In bad weather or in winter, ensure
that the sensors are not covered with
mud, ice or snow. When reverse gear
is engaged, an audible signal (long
beep) indicates that the sensors may
be dirty.

 Press button A again, the warn-
ing lamp switches off, the system
is reactivated.
"HYDRACTIVE III+" ELECTRONIC SUSPENSION
The suspension automatically and
instantly adjusts to different driving
styles and to the profi le of the road,
providing the best compromise be-
tween occupant comfort and vehicle
road holding.
It allows you to alternate between
soft and fi rm suspension settings,
maximising comfort at the same
time as permanently guaranteeing
the highest level of safety. It also
automatically corrects road holding,
according to the vehicle load and
driving conditions.
Also, the "Hydractive III+" suspen-
sion gives you the possibility of
choosing between two modes of
suspension.
A change of suspension mode can
be made either when the vehicle is
moving or when stationary, by press-
ing on button A . Display on the instrument
panel
The suspension mode selected is
displayed on the instrument panel
screen.
Normal mode
This mode favours soft
damping for maximum com-
fort.
If the speed authorised for a
particular position is exceed-
ed, the vehicle reverts automatically
to the normal road position.
SPORT mode
This mode favours dynamic
driving.
The warning lamp on button A
comes on in addition to the
message on the instrument
panel screen.

SPORT mode is retained when you
switch off the engine.

146
9
D R I V I N G
Reactivation
In bad weather or in winter, ensure
that the sensors are not covered with
mud, ice or snow. When reverse gear
is engaged, an audible signal (long
beep) indicates that the sensors may
be dirty.

 Press button A again, the warn-
ing lamp switches off, the system
is reactivated.
"HYDRACTIVE III+" ELECTRONIC SUSPENSION
The suspension automatically and
instantly adjusts to different driving
styles and to the profi le of the road,
providing the best compromise be-
tween occupant comfort and vehicle
road holding.
It allows you to alternate between
soft and fi rm suspension settings,
maximising comfort at the same
time as permanently guaranteeing
the highest level of safety. It also
automatically corrects road holding,
according to the vehicle load and
driving conditions.
Also, the "Hydractive III+" suspen-
sion gives you the possibility of
choosing between two modes of
suspension.
A change of suspension mode can
be made either when the vehicle is
moving or when stationary, by press-
ing on button A . Display on the instrument
panel
The suspension mode selected is
displayed on the instrument panel
screen.
Normal mode
This mode favours soft
damping for maximum com-
fort.
If the speed authorised for a
particular position is exceed-
ed, the vehicle reverts automatically
to the normal road position.
SPORT mode
This mode favours dynamic
driving.
The warning lamp on button A
comes on in addition to the
message on the instrument
panel screen.

SPORT mode is retained when you
switch off the engine.

159
10
C H E C K S
CHECKS
Unless otherwise indicated, check
these components in accordance
with the Maintenance and Warranty
Guide and according to your engine.
Otherwise, have them checked by a
CITROËN dealer.
Battery The battery does not re-
quire any maintenance.
However, check that the
terminals are clean and
correctly tightened, par-
ticularly in summer and
winter.
When carrying out work on the bat-
tery, refer to the "Practical information" section for details of the precautions
to be taken before disconnecting the
battery and following its reconnection.
Air filter and passenger compartment filter
Refer to the Maintenance
and Warranty Guide for
details of the replacement
intervals for these compo-
nents.
Depending on the environment (e.g.
dusty atmosphere) and the use of
the vehicle (e.g. city driving), replace
them twice as often if necessary
(refer to the "Engines" paragraph).
A clogged cabin fi lter may have an
adverse effect on the performance
of the air conditioning system and
generate undesirable odours.
Oil filter
Replace the oil fi lter each
time the engine oil is
changed. Particle filter system (Diesel)
Complementary to the catalytic
converter, this fi lter makes an ac-
tive contribution to the preservation
of air quality by the retaining of the
unburnt pollutant particles. Black
exhaust fumes are thus no longer
emitted.
After prolonged idling or driving at very
low speeds, you may occasionally
notice water vapour being emitted from
the exhaust when accelerating. This is
of no consequence to the running of
the vehicle or to the environment.
If there is risk of clogging, a mes-
sage appears on the instrument
panel display, accompanied by an
audible signal and lighting of the
service warning lamp.
This alert tells you that the particle
fi lter is starting to fi ll up (in conditions
of urban driving of exceptionally long
duration: low speeds, traffi c jams
etc.)
To regenerate the fi lter, it is advised
to drive as soon as possible, when
traffi c conditions permit, at a speed
of 40 mph (around 60 km/h) or
more for at least fi ve minutes (until
the alert message disappears).
If this alert persists, consult a
CITROËN dealer.
Refer to the Maintenance and
Warranty Guide for details of the
replacement interval for this compo-
nent.

168
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb without the use of
any tools.
Headlamps
Model with Xenon headlamps
(D1S)

1. Sidelamps: W 5 W

2. Dual-function Xenon
headlamps (dipped/main): D1S

3. Angular lighting: HP19

4. Daytime-running lamps: HP24 Sidelamps

 Lift up the pegs A to remove the
cover on the headlamp.

 Remove the protective cap B .

 Pull the bulb holder to remove it.

 Replace the bulb and refi t the
bulb holder.
For the maintenance of the front
headlamp unit and the changing of
HP19, D1S and HP24 bulbs, contact
a CITROËN dealer.
Risk of electrocution
Xenon bulbs must be re-
placed by a CITROËN
dealer.
You are advised to change both
D1S bulbs at the same time, if one
of them has failed.

 Refi t the protective cap B .

 Refi t the cover and fi x it in place
using the pegs A .

169
11
P R A C T I C A L I N F O R M A T I O N Main beams Sidelamps

 Lift up the pegs A to remove the
cover on the headlamp.

 Remove the protective cap B .

 Disengage the retaining spring.

 Remove the bulb and replace it,
paying attention to the direction
of fi tting.

 Refi t the retaining spring.

 Refi t the protective cap B .

 Refi t the cover and fi x it in place
using the pegs A .
 Lift up the pegs A to remove the
cover on the headlamp.

 Remove the protective cap B .

 Pull the bulb holder to remove it.

 Replace the bulb and refi t the
bulb holder.

 Refi t the protective cap B .

 Refi t the cover and fi x it in place
using the pegs A .
Model with halogen headlamps

1. Main beams: H1

2. Sidelamps: W 5 W

3. Dipped beams: H7

4. Directional lighting: H7

5. Daytime-running lamps: HP24
For the maintenance of the front
headlamp unit and changing HP24
bulbs, contact a CITROËN dealer.
Halogen bulbs must not be changed
until they have been off for a few
minutes (risk of serious burns).
Do not touch the bulb directly with
your fi ngers, use a lint-free cloth.
It is essential that only anti-U.V.
type bulbs are used in order not to
damage the headlamp.

212
11
22
33
AUDIO
INFORMATION AND ADVICE
The MP3 format, an abbreviation of MPEG 1.2 & 2.5 Audio Layer 3,is an audio compression standard which permits the recording of several tens of music fi les on a single disc.
In order to be able to play a recorded CDR or CDRW , when recording it is preferable to select standards ISO 9660 level 1.2 or Joliet. If the disc is recorded in another format, it may not be played correctly. It is recommended that the same recording standard is always used for an individual disc, with as low a speed as possible (4x maximum) for optimum sound quality. In the particular case of a multi-session CD, the Joliet standard is recommended.
The audio equipment will only play fi les with the extension ".mp3" with a sampling rate of 22.05 KHz or 44.1 KHz. No o ther type of fi le (.wma, .mp4, .m3u...) can be played.
It is advisable to restrict fi le names to 20 characters without using special characters (e.g. " " ? ; ù) to avoid any pl aying or displaying problems.
MP3 CD
Insert the CDs in the changer one by one.
Press the SOURCE button several times in succession and select CD CHANGER.
Press one of the buttons on the numeric keypad to select the corresponding CD.
Press one of the buttons to select a track on the CD. Press and hold one of the buttons for fast forward or rewind play.
CD CHANGER
PLAYING A CD (NOT MP3 COMPATIBLE)

10
NAV
5
6
7
1
2
3
4
8
ADDING A STOPOVER
Enter a new address, for example.
Once the new address has been entered, select START GUIDANCE and press OK to confi rm.
Position the stopover on the list and press OK to confi rm.
Press the NAV button.
Press the NAV button again or select the NAVIGATION MENU function and press OK to confi rm.
Select the ADD A STOPOVER function (5 stopovers maximum) and press OK to confi rm.
Select the STOPOVERS function and press OK to confi rm.
NAVIGATION MENU
STOPOVERS
ADD A STOPOVER
NEW DESTINATION INPUT
To change the stopovers, repeat operations 1 to 3 and s and select OPTIMISE ROUTE (select a stopover, delete it or mov e move it on the list using the ring to change the order, confi rm its new position and fi nish using the ring to change the order, confi rm its new position and fi nish with RECALCULATE.
Stopovers can be added to or deleted from the route once the destination has been selected.
Repeat operations 1 to 7 as many times as necessar y then select RECALCULATE and press OK to confi rm.
START GUIDANCE