display Citroen C5 2008 (RD/TD) / 2.G Owner's Guide

104
III
3
2
6
7
2
3A7
Delayed start-up
Note : Before programming the delayed start-up of the heating, you must ensure that the clock is set to the correct time.
P R O G R A M M A B L E H E A T I N G
Programming the start-up time
Start-up may be programmed between 1 minute and 24 hours in advance.
You can store up to 3 different start-up times, but programme only 1 delayed start-up time.
Factory settings A :
Time 1 : 06:00.
Time 2 : 16:00.
Time 3 : 22:00.
Note : The factory settings are replaced once you adjust them. The programmed times are stored until they are re-programmed.



Press button 3 then buttons 2 or 7 in the next 10 seconds, until the desired start-up time is displayed.
Note : In the event of a battery failure, the factory settings are restored.
Note : if you wish to recall the other stored times, press several times on button 3 in the next 10 seconds until the desired programme number is displayed.
Cancelling the programmed time
To cancel the programmed start-up time, press briefl y on button 3.
Setting the time
Hold button 3 down and press but-ton 2 or button 7. Release button 3, the time is displayed and symbol 6fl ashes.
Use the two adjustment buttons 2(to go forward) or 7 (to go back) until the correct time is displayed.
Holding these buttons down will make the numbers displayed scroll more quickly.
Reading the time
Press button 2 or button 7 to dis-play the time.
When the heating mode is acti-vated, the remaining operating time is displayed in place of the time.

105
III
34
2
3
8
76
Selection and activation of a programmed time
Press button 3 until the programme number corresponding to the required programmed time is dis-played. The chosen pre-selected time is automatically activated after 10 seconds if no other but-tons have been pressed.
To confi rm that the mode is acti-vated, symbols 4 and 8 fl ash until the heating starts up.
When the heating starts up, the warning lamp 9 lights up on the dashboard and the programmer screen.
P R O G R A M M A B L E H E A T I N G
Adjusting the operating durationPress button 3 and hold it down. Press button 2 or 7 at the same time. Release button 3. The time and symbol 6 are displayed.Press again on button 3 and hold it down. Press button 2 or 7 at the same time. Release button 3. The operating duration and symbol 8 is displayed.Adjust the operating duration with button 2 or 7.
Note : The operating duration is memorised when the time indicated disappears or by pressing button 3.
Adjusting the remaining operating duration
When heating mode is activated, the remaining operating time can be modifi ed within the range of 10 to 60 minutes using buttons 2 or 7.
Note :The pre-selected start-up time can be modifi ed or cancelled by following the instructions previ-ously given above.
In the event of a battery discon-nection, the programmer must be re-set (hours, minutes etc.)


Always switch off the additional heating when filling up with fuel, to prevent any risk of fi re or explosion.
To avoid any risk of intoxica-tion or asphyxiation, the addi-tional heating must not be used, even for short periods, in an enclosed area such as a garage or workshop not equipped with a system for the extraction of exhaust gases.
Do not park the vehicle over infl ammable materials (e.g. dry grass, dead leaves or paper) as this could present a fi re risk.
The programmable heating sys-tem is supplied by the vehicle’s fuel tank. Before use, ensure that the remaining fuel level is suffi cient. If you are using the reserve fuel tank, we strongly advise you not to use the pro-grammable heating system.

108
III
A
A I R B A G S
Front passenger's airbag deactivation
In order to be able to use a rear-facing child seat in the front pas-senger's seat position, it is impera-tive to deactivate the passenger's airbag.
For that:With the ignition switched off, insert the key into the switch A.
Turn the key to the “OFF” posi-tion, the passenger's airbag is deactivated.With the ignition on, the front passenger's airbag deactiva-tion warning lamp lights up on the roof console display.

127
IV
S
11
10
9
1
4
5
6
7
8
3
2
ABCDEFGHIJK
NPMROQL
R D S A U D I O C O M P A C T D I S C S Y S T E M
Multifunction display
Technical specifi cations
Your Bluetooth® compatible radio possesses:®
3 wavebands (MW/LW/FM).
Dual tuner with RDS EON PTY, display of the PS name, RDS programme search, TA traffi c informa-tion, 24 pre-selections (18 FM - 6 MW/LW), auto-matic memorisation of the AST strongest stations.
An MP3- compatible CD player.
Audio power of 4x35 W.

128
IV
B U T T O N C O N T R O L S
AOn / Off.Volume adjustment.
BCD eject.
CCD aperture.
DSOURCESelection of source (CD/MP3 CD and CD changer source).
EBAND/ASTShort press: Selection of frequency bands and memory banks.Long press: Automatic pre-set function (Autostore).
FCall-up of audio adjustments:Sound ambiences, bass, treble, loudness, fade, balance, Call-up of audio adjustments:
speed-sensitive volume.
GLIST
Radio source:Short press: Display of the list of radio stations available (30 maximum). Display of the list of radio stations available Display of the list of radio stations available
Long press: Update of list of stations.(30 maximum).(30 maximum).
CD source:Long press:Long press: Display of list of tracks of the CD.Long press:
HESCShort press: Cancel the current operation or delete a super-imposed display.Long press: Return to the permanent display.
ITA /PT YShort press: TA function (road information).Long press: PTY function (selection of programme type).TA function (road information).TA function (road information).
JRadio source: Manual search of higher frequencies.CD/MP3 changer source: Manual search of higher frequencies. Selection of previous CD / previ- Manual search of higher frequencies. Manual search of higher frequencies.
ous CD-cover.CD/MP3 changer CD/MP3
Other sources: Scrolling in the Main Menu.
K
Radio source: Automatic search of higher frequencies.CD source, CD changer source and MP3 source:Automatic search of higher frequencies.
Short press:CD source, CD changer source and MP3 source: Forward search for tracks.CD source, CD changer source and MP3 source:
Long press: Fast forward with accelerated sound.Other sources:Long press: In the menus, choice of your adjustments.If your vehicle has the Bluetooth In the menus, choice of your adjustments.® In the menus, choice of your adjustments. In the menus, choice of your adjustments. system:® Selection of In the menus, choice of your adjustments.
characters.
LOKButton for validation and activation/deactivation of certain functions.If your vehicle has the Bluetooth® system: Answer call, end ®call.
MRadio source: Manual search of lower frequencies.CD/MP3 changer source: Selection of the next CD / next CD-cover.CD/MP3 changer
Other sources: Scrolling in the Main Menu.
N
Radio source: Automatic search of lower frequencies.CD source, CD changer source and MP3 source:Short press:CD source, CD changer source and MP3 source:CD source, CD changer source and MP3 source: Reverse search for tracks.CD source, CD changer source and MP3 source:CD source, CD changer source and MP3 source:
Long press: Rapid reverse with accelerated sound.Other sources:Long press:Long press: In the menus, choice of your adjustments.If your vehicle has the Bluetooth In the menus, choice of your adjustments. In the menus, choice of your adjustments.® In the menus, choice of your adjustments. In the menus, choice of your adjustments. system:® Selection of In the menus, choice of your adjustments. In the menus, choice of your adjustments.
characters.
OMENUDisplay of the Main Menu.In certain countries, this control is deactivated while the ve-hicle is moving.
P1- 6Radio source:Short press: Recall of pre-set stations.Long press: Memorisation.CD changer source:Long press: Selecting a CD.
QDARKShort successive presses:One press: Display of radio, time and temperature only.Two presses: Display off (blank display). Display of radio, time and temperature only Display of radio, time and temperature only
Three presses: Return to the standard display.
RMODESelection of the type of information shown on multifunction display.
SCD changer.

129
IV
B U T T O N C O N T R O L S
The controls at the steering wheel give you access to certain functions, without you needing to use the radio-CD control panel.
1
Shor t press
- Cancel the current operation and return t o t h e p r ev i o u s m u l t i f u n c t i o n d i s p l ay screen.- For an incoming call: Refuse the call.
Long pressRetur n to the or iginal multifunc tion dis -play.
2RIGHT CONTROL
Rotate
- Radio mode: Scroll through pre-set sta-tions.- CD/MP3 CD and CD changer source: Scroll through CDs or chapters.- In the multifunction display menus: Move around and increase/decrease.
Shor t press
- In the multifunction display menus: Vali-dation.- Open shor tcut menus.- For an incoming call: Answer call.
Long pressOpen the multifunction display main menu.
3MENUShor t pressA c c e s s t h e m u l t i f u n c t i o n d i s p l ay m a i n menu.
4VOL +Shor t press / Press and holdIncrease volume.
5VOL -Shor t press / Press and holdDecrease volume.
6MUTEShor t press- First press: mute.- Second press: cancel mute.
7
Shor t press
- Radio source: Automatic search of higher frequencies.- CD/MP3 CD and CD changer source: Search of the next track.
Long press- CD/MP3 CD and CD changer source: Fast forward with accelerated sound.
8
Shor t press
- Radio source: Automatic search of low-er frequencies.- CD/MP3 CD and CD changer source: Search of previous track.
Long press- CD/MP3 CD and CD changer source: Rapid reverse with accelerated sound.
9LISTShor t press
- Radio source: Display of the list of radio stations available.- CD/MP3 CD and CD changer source: Display of list of tracks of the CD.
Long pressUpdate of list of stations.
10LH BUTTON
Short pressActivation of voice recognition.
Long pressNavigation instructions.
11RH BUTTONPressScroll through the multifunction display screen.

131
IV
Notes on radio reception
Your radio will be subject to certain phenomena that are not encoun-tered by domestic systems.
The reception of AM and FM sig-nals may suffer from interference, which is caused by the nature and propagation of the signals and does not refl ect on the quality of your radio installation.
In AM mode, the reception may be affected when passing under power lines or bridges, or when travelling through tunnels.
In FM mode, the reception may be affected by the distance from the station transmitter, the refl ect-ing of signals off obstacles (moun-tains, hills, tower blocks) and radio blackspots (no coverage from the station transmitter).
Selection of radio source
Press button D to select the source.
R A D I O S O U R C E
Selection of frequencies and memory banks
Press button E successively to go through the memory banks FM1, FM2 and FM3, for the FM waveband, and the mem-ory banks MW/LW, for the AM waveband.
Manual search
Manual search is via buttons Jor M.
By keeping button J or M pressed, you will be able to scroll through the waveband. Scrolling will stop as soon as you release the button. The radio will remain tuned to the frequency that is displayed.
Tuning sensitivity
Automatic searches can be carried out according to two levels of sen-sitivity:To capture the most powerful transmitters, choose the local search mode “LO” (default option).To capture the weakest or most distant transmitters, choose the sensitive search mode “DX”.

132
IV
Display and selection of a station available in the area in which you are travelling
Briefl y press on button G or but-ton 9 at the steering wheel to dis-play the list of stations. This list is updated every 10 minutes.
You can also update this list at any time by making a long press on button G or button 9 at the steer-ing wheel.
To listen to one of these stations, select by pressing buttons J or Mand validate using button L.
Manual pre-setting
Select the waveband and memory bank required using button E.
Select a station using either auto-matic or manual search.
Keep pressing for more than two seconds on one of the pre-selection buttons 1 to 6 on the keypad P.
The sound momentarily cuts off, then returns to its previous level to confi rm that it has memorised the station.
R A D I O S O U R C E
Automatic memorisation of transmitters (Autostore function)
In FM, if you hold down button Efor more than two seconds, your radio will automatically memorise the 6 strongest stations on the FM3 memory bank.
The display shows “FM AST”.
The radio memorises the 6 strong-est transmitters, deleting the 6 pre-viously memorised.
After the memorisation, the radio goes directly to memory 1 of mem-ory bank FM3.Note:If the traffi c information func-tion has been activated (see RDS SYSTEM), the stations offering this facility will be mem-orised as priority.
If it is unable to memorise any new stations, the system will retain the previously memo-rised stations.If the system is unable to fi nd 6 stations, the unfi lled memory slots will remain free.

133
IV
Using the RDS (radio data system) function on FM
The majority of FM radio stations use the RDS system. The radio in your vehicle has this system.
The RDS system enables these stations to transmit non-audible data in addition to the broadcasting of their programmes. The data pro-vides access to various functions described in this chapter, such as: display of the station name, inter-mittent traffi c information fl ashes or automatic scanning of stations. This enables you to continue lis-tening to your chosen radio station, regardless of the different frequen-cies it uses in the regions through which you are travelling.
Scanning of RDS stations
Your radio keeps the best possible reception by continuously looking for any other frequencies on which the selected radio station is broad-cast, automatically choosing the frequency offering the best recep-tion (if the station broadcasts on more than one transmitter or fre-quency).
R D S S Y S T E M
Activation/deactivation of the RDS functions
The RDS functions can be accessed via the following two menus:Main menu (press button O).
AUDIO menu (press button L).
To activate/deactivate the RDS functions
1. Press on button O.2. Select the AUDIO icon using buttons J or M.3. Confi rm your choice with a press on button L.4. Select the sub-menu for the FM waveband, via buttons J or M. Confi rm your choice with a press on button L.5. Select scanning for RDS sta-tions, via buttons J or M.6. Validate your choice with a press on button L.7. Using control L, select/deselect to activate/deactivate the func-tion.8. Validate your choice by select-ing “OK” on the display.

135
IV
Selecting CD source
After inserting a CD, with the printed side facing upwards, the player will start playing the CD automatically.
To change manually to CD source (CD already inserted), press but-ton D until you obtain the source you require.
Ejecting a CD
Press button B to eject the CD, the audio system will automatically switch to radio source.
If the CD is not removed within 10 to 15 seconds of being ejected, it will automatically be taken back into the CD player, although it will not be played.
Selecting a track
Press button K once to play the next track.
Press button N once to return to the beginning of the track currently being played, press a second time to go back to the start of the previ-ous track.
Press the buttons successively to skip several tracks at a time.
You can also perform this opera-tion using button G or button 9 at the steering wheel.
When the track listing is displayed, select the desired track using but-tons J or M then validate with but-ton L.
C D S O U R C E
You can also do this via the con-trols 7 and 8 at the steering wheel.
Fast forward and rapid reverse with accelerated sound
To move swiftly through the CD, press and keep pressed button Kor N, respectively for fast forward or rapid reverse with accelerated sound.
You can also do this via the con-trols 7 and 8 at the steering wheel.
Play resumes as normal when the button is released.
Menu
This menu allows activation/deac-tivation of two options:Playback of the fi rst 7 seconds (approx.) of each track of the CD.
Random playback of the CD tracks.
This can be accessed in two ways:Either by pressing button Oand proceeding as for Scan-ning of RDS stations – the sub-menu for Audio Preferences.
Or, provided you are in CD source, by pressing on but-ton L. You can then access the Audio menu.
Note: If one of these options is active, it remains active for CD changer source.