engine Citroen C5 2008 (RD/TD) / 2.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C5, Model: Citroen C5 2008 (RD/TD) / 2.GPages: 240, PDF Size: 5.78 MB
Page 147 of 240
150
V
11
Topping up engine oil
B e f o r e fi l l i n g , p u l l o u t t h e d i p s t i c k .
C h e c k t h e d i p s t i c k a f t e r fi l l i n g .
It must never exceed the maxi-mum.
Screw the cap back on and close the bonnet.
L E V E L S
R a d i a t o r – c o o l a n t fl u i d
Checking the level and topping up w i t h fl u i d m u s t a l w a y s b e d o n e w i t h the engine cold.
Engine hot
Wait 15 minutes or for the tempera-ture to be lower than 100 and then carefully unscrew the cap so as to allow the pressure to drop, protect-ing yourself with, say, a cloth.
Topping up the coolant
The level of coolant 1 should be between the MIN. and MAX. mark-ings on the header tank.
Top up the level. If the top up requires more than 1 litre, contact a CITROËN dealer.requires more than 1 litre, requires more
Make sure that the cap is back on properly.Note:If you need to top up the fl u i d f r e q u e n t l y , t h i s i n d i c a t e s a malfunction which you should get checked at the earliest opportu-nity.
Remark: The cooling fan may operate for around 10 minutes after the engine has stopped.
If opening the bonnet when the engine is hot, even if it is stopped and the ignition is switched off, remember that the cooling fan may operate at any moment.
Page 148 of 240
151
V
1
2
4
3
D I E S E L I N J E C T I O N E Q U I P M E N T
Protective cover for HDi 138 engines:
Remove the protective cover by fi r s t u n c l i p p i n g a t 3, then 1 and 4.
Unclip at 2 by pulling towards you, then lift up.
T o r e fi t t h e p r o t e c t i v e c o v e r , fi r s t l y clip in at 2. Lower and centre the cover. Clip in at 3 and 4, pushing vertically and gently from the rear.Clip in at 1 pushing vertically.
Protective cover for HDi 110, HDi 173 and V6 HDi 208 engines:
Pull the protective cover upwards to remove.
Draining water from the fuel fi l t e r
Drain regularly (at each oil change).
To drain the water, slacken the bleed screw or the water in diesel fuel sensor, located at the base of t h e fi l t e r.
Continue until all the water has fl o w e d o u t.
Then retighten the bleed screw or the water detection sensor.
HDi engines are the result of advanced technology.
A n y i n t e r v e n t i o n r e q u i r e s s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a CITROËN dealer can guarantee. A n y i n t e r v e n t i o n r e q u i r e s s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a A n y i n t e r v e n t i o n r e q u i r e s s p e c i a l q u a l i fi c a t i o n s w h i c h o n l y a
Page 149 of 240
152
V
D I E S E L I N J E C T I O N E Q U I P M E N T
In the event of running out of fuel:
HDi 110 engineHDI 138 and HDi 173 engines
V6 HDi 208 engine with priming pump
After adding fuel, turn the ignition key to position M, wait for a few seconds, then operate the starter motor until the engine starts.
If the engine fails to start after sev-eral attempts, contact a CITROËN If the engine fails to start after sev-after sev-
dealer.
HDi 110, HDi 138 and HDi 173 engines with priming pump
A f t e r fi l l i n g ( m i n i m u m 5 l i t r e s ) a n d removing the protective cover, action the manual priming pump, until some resistance is felt.
Operate the starter motor while depressing the accelerator pedal slightly until the engine starts.
I f t h e e n g i n e f a i l s t o s t a r t a t t h e fi r s t attempt, wait 15 seconds before trying again.
If the engine fails to start after a few attempts, action the priming pump again and then try to start the engine.
When the engine is idling, acceler-ate slightly to complete the bleed-ing of the circuit.
Page 150 of 240
153
V
Engine typeEngine oil capacities (in litres)(1)
1.8i 16V Engine5.0
2.0i 16V Engine5.0
3.0i 16V Engine 4.75 / 5.0(2)
HDi 110 FAP Engine 3.75
HDi 138 FAP Engine5.25
HDi 173 FAP Engine5.25
V6 HDi 208 FAP Engine 5.5 / 5.75(2)
S c r e e n w a s h fl u i d ( i n l i t r e s )3.5
Screen wash and h e a d l a m p w a s h fl u i d ( i n l i t r e s )6.15
(1) A f t e r d r a i n i n g b y g r a v i t y w i t h c h a n g e o f o i l fi l t e r .(2) A f t e r d r a i n i n g b y s u c t i o n w i t h c h a n g e o f o i l fi l t e r .
C A P A C I T I E S
Page 151 of 240
154
V
A
B
+ 1
- 4- 3
+ 2
Starting the engine after disconnecting and reconnecting the battery
1. Turn the ignition key.
2. Wait approximately 1 minute before operating the starter in order to allow the electronic systems to re-initialise.
After the battery has been discon-nected for a lengthy period of time, it may be necessary to re-initialise the following functions:
The anti-pinch on the windows.
The parameters of the multi-function display (date, time, language etc).
The Radio stations.
The NaviDrive. See NaviDrive instructions.
Page 152 of 240
155
V
+ 1
- 4- 3
+ 2
A
B
C
1 2 V B A T T E R Y
V 6 H Di E N G I N E
Starting the engine with an assisting battery
If the battery is discharged, it is possible to use either a separate emergency battery or a battery on another vehicle.
If you use the battery on another vehicle, stop the engine on the latter. The two vehicles must not come into direct contact with each other.
Check that the assisting battery h a s s u f fi c i e n t v o l t a g e ( 1 2 V ) .
Lift up the pegs to remove the front left-hand headlamp cover.
Connect the cables according to the order indicated in the dia-ordergram.
A Pole “+” of the broken down vehicle (Under the red cover).B Assisting battery.C Pole “–” of the broken down vehicle (Under the bonnet).
Check that the leads are well secured (risk of sparks).
Start the engine of the assist-ing vehicle. Let the engine run for around 1 minute at a slightly accel-erated idle.
Operate the starter on the vehicle being assisted.
It is essential to follow the indi-cated sequence correctly.
N e v e r a p p r o a c h w i t h a fl a m e o r c r e a t e s p a r k s i n t h e v i
c i n i t y o f t h e b a t t e r y ( e x p l o s i v e g a s ) .
The battery contains dilute sulphuric acid which is hig hly corrosive.
When handling batteries, always protect your face and es pecially your eyes.
In the event of any contact with the skin, rinse immediatel y with copious amounts of fresh water.
For any battery replacement, contact a CITROËN dealer.
Do not touch the leads during the operation.
Do not lean over the batteries.
Disconnect the cables in reverse order, making sure they do not touch together.
Advice
Battery location and access
The battery is located in the boot under the left hand wing trim. To a c c e s s t h e b a t t e r y , o p e n t h e fl a p .
IMPORTANT
In the event of a battery failure, and if the boot is closed, it is then necessary to feed an electrical supply to your vehicle.
Page 155 of 240
158
V
T A B L E O F F U S E S
Fusebox C
Ref.RatingFunction
F115ARear screen wipe (Tourer)
F230ALocking and deadlocking relay
F35AAirbags
F410AAutomatic gearbox - Additional heater unit (Diesel) - Electrochrome rear view mirrors
F530AFront window - Sun roof - Passenger door lighting - Passenger rear view mirror adjustment
F630ARear window
F75AVanity mirror lighting – Glove box lighting – Interior lamps - Torch (Tourer)
F820A R a d i o - C D c h a n g e r - C o n t r o l s a t t h e s t e e r i n g w h e e l – D i s p l a y – T y r e d e fl a t i o n detection - Electric boot ECU
F930ACigar-lighter - Front 12V socket
F1015AAlarm - Controls on the steering wheel, signalling and screen w ipe controls
F1115ALow current anti-theft switch
F1215ADriver’s electric seat - Instrument panel - Seat belt not fastened warning lamps - Air conditioning controls
F135AEngine relay unit - Hydraulic suspension pump cut-off relay - Airbag ECU supply
F1415ARain and brightness sensor - Parking assistance - Passenger’s electric sea t - Trailer r e l a y u n i t - H I F I a m p l i fi e r E C U - H a n d s - f r e e k i t - L a n e D e p a r t u r e W a r n i n g S y s t e m
F1530ALocking and deadlocking relay
F1740AHeated rear screen - Exterior heated rear view mirrors
FSHSHUNTCUSTOMER PARK SHUNT
Page 156 of 240
159
V
F U S E S
U N D E R T H E B O N N E T
To access the fusebox under the bonnet, undo each screw by a 1/4 turn.
After a repair, take care to reclose the cover.
Any repairs on the MAXI fuses (that give additional protection), located in the fuseboxes, must be left to a CITROËN dealer.fuseboxes, must be left to a fuseboxes, must be left to a
Ref.RatingFunction
F120AEngine control unit
F215AHorn
F310AScreen wash pump
F410AHeadlamp wash pump
F515AStarter
F610A A i r fl o w m e t e r - D i r e c t i o n a l h e a d l a m p s - D i a g n o s -
F710AAutomatic gearbox lever lock - Power steering
F825AStarter
F910AClutch switch - STOP switch
F1030AStarter
F1140AAir conditioning blower
F1230AWipers
F1340ABSI supply (ignition on)
F1430A-
F1510ARight-hand main beam
F1610ALeft-hand main beam
F1715ARight-hand dipped beam
F1815ALeft-hand dipped beam
F1915AStarter
F2010AStarter
F215AStarter
Page 158 of 240
161
VI
A
F U E L
If you should put in fuel that is not suitable for your vehicle's engine type, it is imperative to have the tank drained be fore you start the engine again.
While you are refuelling, the engine must be stopped and the ignition switched off.
For a petrol engine with a cata-lytic converter, unleaded fuel is compulsory.
T h e fi l l e r n e c k i s n a r r o w e r t o e n s u r e t h a t o n l y u n l e a d e d p e t r o l c a n b e p u t i n .
W h e n y o u a r e s e e k i n g t o fi l l y o u r tank, do not persist after the third cut-off ; this could cause your vehicle to malfunction.
F u e l fl a p
T o o p e n , p r e s s a t t h e t o p l e f t - h a n d c o r n e r , t h e n p u l l o p e n f r o m t h e l e f t .
L o c k i n g fi l l e r c a p
T u r n t h e k e y a q u a r t e r t u r n t o l o c k a n d u n l o c k t h e fi l l e r c a p .
W h e n r e f u e l l i n g , p l a c e t h e c a p o n h o o k A .
Fuel quality
A l a b e l i n s i d e t h e fi l l e r fl a p t e l l s y o u w h i c h t y p e o f f u e l t o u s e .
T h e p e t r o l e n g i n e s a r e d e s i g n e d t o r u n o n R O N 9 5 .
H o w e v e r , f o r b e t t e r p e r f o r m - a n c e ( p e t r o l e n g i n e ) , w e r e c o m - m e n d R O N 9 8 .
Tank capacity
T h e t a n k h a s a c a p a c i t y o f a p p r o x i - m a t e l y 7 1 l i t r e s .
Page 175 of 240
178
VI
2312312
DIESEL ENGINE HDi 173 FAP
It is essential to remove the very cold protection:
When the outside temperature exceeds 10 °C.
When driving at speeds of over 120 km/h (approximately 75 mph).
V E R Y C O L D P R O T E C T I O N
DIESEL ENGINE V6 HDi 208 FAP
Snow situation
S l i d e t h e d e fl e c t o r 1 i n t o t h e a i r d u c t 2 a n d c l i p i n .
M o v e a b l e d e v i c e w h i c h p r e v e n t s t h e i n t a k e o f s n o w p a r t i c l e s , w h i c h c o u l d o b s t r u c t t h e a i r fi l t e r .
Snow situation
P u s h a n d r o t a t e t h e k n o b 1 b y 9 0 ° i n t h e d i r e c t i o n o f t h e a r r o w i n o r d e r t o p o s i t i o n t h e s h u t t e r 2 i n a v e r t i - c a l p o s i t i o n i n t h e a i r d u c t 3 .
Note : T o r e t u r n t o t h e n o r m a l s i t u - a t i o n , p u s h t h e k n o b 1 then rotate i n t h e o p p o s i t e d i r e c t i o n .
Normal situation
T h e s h u t t e r 2 i s i n a h o r i z o n t a l p o s i t i o n i n t h e a i r d u c t 3 .