length Citroen C5 2008 (RD/TD) / 2.G Owner's Manual

96
III
A U T O M A T I C A I R C O N D I T I O N I N G
G E N E R A L
You are advised to use the auto-matic air conditioning regulation. This automatically regulates the following functions for maximum comfort : air fl ow, passenger com-partment temperature, and air dis-tribution, using different sensors (external temperature, sunlight). This avoids the need to alter any of the settings, with the exception of the temperature displayed.
Take care not to obstruct the sun-light sensor A.
Provided you retain automatic mode (by pressing button “AUTO”) and all the air vents are open, you will maintain an optimum comfort level, also removing humidity and misting, whatever the ambient cli-matic conditions.
The temperature inside the cabin cannot be lower than the tempera-ture outside if the air conditioning is not operating.
To be effective, the air conditioning should only be used with the win-dows closed. If after a lengthy stop in bright sunlight the interior tem-perature is excessive, air the pas-senger compartment by opening the windows for a few moments, then close them again.
Air circulation
For your comfort we advise you to maintain a proper distribution of air within the cabin, both at the front and at the rear.
To obtain an even distribution of air, ensure that you do not obstruct the external air inlet grille located at the base of the windscreen, the air vents, the air outlets on the fl oor underneath the front seats, and the air extractor located behind the fl aps in the boot.
The front and rear air vents are fi t-ted with control knobs which allow you to control and direct the air fl ow. It is recommended to keep all the air vents open.
Dust/pollen fi lter
There is a fi lter for excluding pollen and dust.
This fi lter has to be changed accord-ing to the vehicle maintenance sched-ule. See “Maintenance Guide”.
To ensure the correct operation of the air conditioning system, it is essential to operate the air condi-tioning at least once a month.
The air conditioning operates by using power from the engine. This results in a slight increase in fuel consumption.
In certain extreme operating con-ditions (e.g. carrying a full load up a steep gradient in high tempera-tures), the switching off of the air conditioning allows more power to be transferred to the engine, thereby increasing the towing capacity.
Air inlet
Check that the exterior grille for the air inlet, at the bottom of the wind-screen, is clean and free of dead leaves, snow, etc.
If washing the vehicle with a high pressure jet, avoid targeting the air inlet zone.

123
III
33
44
1
1
22
The cargo net can be used behind the rear seats (row 2) when the luggage-cover blind is not fi tted, or behind the front seats (row 1).
Note : when using behind the front seats, the backrests and the seat cushions must be folded down (see section on rear seats).
CARGO NET (TOURER)
To install :
Fold down the backrests of the rear seats.
Position the cargo net roller over the two rails 1 located behind the rear seats (2/3 benchseat). The two notches 2 must be posi-tioned over the two rails.


Slide the 2 rails 1 into the notches 2 and push the roller (lengthwise) from right to left to lock it in.Put the backrests of the rear seats back into place.


To use in row 1 :
Fold down the backrests of the rear seats.
Open the cov-ers 3 of the corresponding high fi xing locations.


To use in row 2 :
Open the cov-ers 4 of the c o r r e s p o n d -ing high fi xing locations.
From the rear benchseat, unroll the cargo net by pushing it to disengage the retaining notches.
Position one of the ends of the cargo net’s metal bar in the corre-sponding fi xing location. Ensure that the notch is correctly lodged in the rail located inside the loca-tion 4.
Position the other notch in the 2nd fi xing location and pull the metal bar towards you.




Unroll the cargo net and posi-tion one of the ends of the net’s metal bars in the corresponding fi xing location. Ensure that the notch is correctly lodged in the rail located inside the location 3.
Pull on the cargo’s net’s metal bar to position the other notch in the 2nd fi xing location.



154
V
A
B
+ 1
- 4- 3

+ 2
Starting the engine after disconnecting and reconnecting the battery
1. Turn the ignition key.
2. Wait approximately 1 minute before operating the starter in order to allow the electronic systems to re-initialise.
After the battery has been discon-nected for a lengthy period of time, it may be necessary to re-initialise the following functions:
The anti-pinch on the windows.
The parameters of the multi-function display (date, time, language etc).
The Radio stations.
The NaviDrive. See NaviDrive instructions.

4646
V
ABCD
A1A2A3A4
C1C2C3C4
A1
A2
A3
A4
B1
B2
B3
C1C2
C3
C4
A5
B1B2B3
D1D2D3D4
A5
D1
D2
D3
D4
A
B
C
D
T E L E P H O N E
M E N U S T R U C T U R E
WHAT ARE THE FUNCTIONS OF THE TELEMATICS MENU ?
MAKING A TELEPHONE CALLC onsult t he list of inc oming, outgoing and mis se d calls.Compose a telephone number on the numeric keypad.
Select a fi le in the directory.
Consult your voice mail.
O PERATING THE TELEPHONE DIRECTORYConsult, modify, create or delete a directory fi le.
Select or name a directory. Choose the start directo ry.
Send or receive one or more fi les by infrared or from the SIM card.
READING , SENDING , EDITING OR DELETING AN SMS MESSAGERead SMS messages received or stored.Send a stored SMS.
Drafting an SMS.
Delete all stored SMS messages.
Select one of the CITROËN network services (depend-ing on subscription).
SETTING PARAMETERS FOR THE TELEPHONE FUNCTIONS
Conf igure the net wor k search mode or c onsult the networks available.Consult the length of one or all of the incoming or outgo-ing calls. Reset the counter to zero.
Ac t i vate, de ac t i vate, m e m o r i s e o r m o di f y t he PI N code.Confi gure the displaying of the number, the automat ic pick up, the ring tone and the call return. Delete the log of calls.