STOP Citroen C5 2009.5 (RD/TD) / 2.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2009.5, Model line: C5, Model: Citroen C5 2009.5 (RD/TD) / 2.GPages: 314, PDF Size: 19.25 MB
Page 140 of 314
IX
!
123
D R I V I N G
MANUAL PARKING BRAKE
Mechanical device for immobilising
the vehicle when stationary. This warning lamp comes
on if the parking brake is en-
gaged or not fully released.
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning lamp
i n d i c a t e s t h a t t h e b r a k e fl u i d l e v e l
is low or a malfunction of the brake
force distributor.
It is essential to stop the vehicle.
Consult a CITROËN dealer.
Application
Pull the parking brake lever up to
immobilise your vehicle.
To facilitate the action on the lever,
you are recommended to press the
brake pedal at the same time.
In all circumstances, as a pre-
cautionary measure, engage
fi r s t g e a r .
On steep gradients, turn the steer-
ing wheel towards the pavement. Release
Press on the end of the lever
whilst pulling it then lower it fully.
Page 141 of 314
IX!!
124
D R I V I N G
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake
is automatically applied
when the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y :
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobil-
ise the vehicle you need to manually
apply the parking brake by pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
-
the display of a message "hand-
brake on" on the instrument panel
screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m
to you the application/release of
your electric parking brake.
- the lighting of warning
lamp P on control A and
on the instrument panel,
-
the display of a message "hand-
brake on" on the instrument panel
screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Page 145 of 314
IX
!
127
D R I V I N G
Dynamic emergency braking
In the event of a failure of the vehi-
cle’s main braking system or in an
exceptional situation (e.g. driver taken
ill, under instruction, etc) pull and
hold control A to stop the vehicle.
The electronic stability programme
( E S P ) p r o v i d e s s t a b i l i t y d u r i n g d y -
namic emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel display:
- "Parking brake faulty".
- "Parking brake control faulty". I f a f a i l u r e o f t h e E S P s y s -
tem is signalled by the light-
ing of this warning lamp,
then braking stability is not
guaranteed. In this event, stability
must be assured by the driver by
repeating alternate "pull release" ac-
tions on control A .
The dynamic emergency
braking must only be used in
exceptional circumstances. Emergency parking brake
release
In the event of the electric parking
brake failing to release, an emer-
gency device can be used to release
the parking brake manually, provid-
ed that it is possible to immobilise
the vehicle while the procedure is
carried out.
If you can start the vehicle: with
the engine running, immobilise
the vehicle by applying the foot
brake while the operation is be-
ing carried out.
If you are unable to start the ve-
h i c l e ( fl a t b a t t e r y f o r e x a m p l e ) : d o
not use this device and contact
a CITROËN dealer. However, if
y o u a r e o b l i g e d t o p r o c e e d , fi r s t
immobilise your vehicle securely
and then follow the instructions
below.
Page 148 of 314
IX
130
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the follow-
ing warning lamps:
a n d / o r fl a s h i n g - The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
Pull the control lever for at least 5 seconds or until maximum
application.
S w i t c h o n t h e i g n i t i o n a n d c h e c k t h a t t h e e l e c t r i c p a r k i n g b r a k e
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
S w i t c h o n t h e i g n i t i o n .
Push the control lever and hold it for approximately 3 seconds.
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
a n d / o r fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
Wait approximately 3 minutes.
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switch ing off the engine.
Page 154 of 314
IX
136
D R I V I N G
Automatic operation
Move the gear lever to position D .
The gearbox constantly selects the gear that is best suited to the
following parameters:
- driving style,
- r o a d p r o fi l e
- vehicle load.
The gearbox operates without requir-
ing any intervention on your part.
For certain manoeuvres (for ex-
ample overtaking), you can obtain
maximum acceleration by pressing
the accelerator pedal hard down
past the point of resistance, which
then produces an automatic change
down to a lower gear. When braking, the gearbox may
change down automatically in order
to provide effective engine braking.
If you lift your foot off the accelera-
tor abruptly, the gearbox will not en-
gage a higher gear.
Manual operation
Position of the gear lever for manual
gear changing.
Move the gear lever to position M .
Push the gear lever towards the
" + " sign to change up a gear.
Pull the gear lever towards the
" - " sign to change down a gear. - If the vehicle stops or reduces
speed (for example when ap-
proaching a stop sign), the gear-
box changes down automatically
t o fi r s t g e a r .
- In sequential mode, it is not nec- essary to release the accelerator
during gear changes.
- A request to change gear is ac- cepted only if the engine speed
permits it.
- The SPORT and SNOW modes
do not operate in sequential
mode.
Page 159 of 314
IX
141
D R I V I N G
In the event of a steep descent or
under excessive acceleration, the
speed limiter (which does not act
on the brakes) may not be able to
prevent the vehicle from exceeding
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
of-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed dis-
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
to return below the maximum speed,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
cle from exceeding the programmed
speed (e.g. on a steep descent or
under excessive acceleration).
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed. Return to normal driving
Either press on button 5 .
Or select the speed limiter func-
tion.
Or stop the engine.
Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 161 of 314
IX
!
143
D R I V I N G
Cruise control must only be
u s e d w h e r e t h e t r a f fi c c o n d i -
tions permit driving at a con-
stant speed.
Do not use it on congested roads
or when the weather or the road
conditions are poor.
The driver must remain attentive
and in complete control of the ve-
hicle.
You are recommended to keep your feet within range of the pedals.
Overriding the programmed
speed
While cruise control is in operation,
it is always possible to go above the
programmed speed simply by pres-
sing the accelerator pedal (for ex-
ample to overtake another vehicle).
The speed displayed in zone A
fl a s h e s .
You only have to release the ac-
celerator pedal to return to the pro-
grammed speed.
Suspension/Resumption
Either by pressing the brake
pedal or the clutch pedal.
Or by pressing button 3 .
O r b y t h e E S P o r A S R s y s t e m s
being active.
For vehicles with a manual gearbox,
cruise control is deactivated if the
gear lever is in neutral. Reactivation
-
By recalling the memorised
speed
After deactivation, press button 3 .
Your vehicle automatically returns
to the memorised cruising speed.
The memorised speed and "ON"
are displayed in zone A .
If the memorised cruising speed is higher than the current speed,
the vehicle will accelerate strong-ly to reach the current speed.
- By selecting the current speed
Press button 1 or 2 once the de-
sired speed has been reached.
The new speed and "ON" will
appear in zone A .
Return to normal driving
Either press on button 5 .
Or select the cruise control func-
tion.
Or stop the engine.
The speed that was chosen is no
longer memorised.
"PAUSE" will be displayed in zone A
of the instrument panel.
These actions do not cancel the
cruising speed which remains dis-
played on the instrument panel. Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the
SERVICE warning lamp.
Have it checked by a CITROËN
dealer.
Page 178 of 314
X
!
160
C H E C K S
Screenwash and headlamp
wash fluid
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e
topped up or replaced with water.
Reservoir capacities:
-
screenwash: approximately 3.5 litres,
- screenwash and headlamp wash: approximately 6.15 litres. Diesel additive level
(Diesel engine with particle
emission filter)
A low additive level is indicated by
lighting of the service warning lamp,
accompanied by an audible warning
and a message on the multifunction
screen.
Topping up
This additive must be topped up by
a CITROËN dealer without delay.
Used products
Avoid prolonged contact of
u s e d o i l o r fl u i d s w i t h t h e s k i n .
M o s t o f t h e s e fl u i d s a r e h a r m f u l t o
health or indeed very corrosive.
Do not discard used oil or
fl u i d s i n t o s e w e r s o r o n t o t h e
ground.
Take used oil to a CITROËN dealer
(France) or an authorised waste
disposal site.
I n t h e c a s e o f v e h i c l e s fi t t e d
with headlamp washers, the
m i n i m u m l e v e l o f t h i s fl u i d i s
indicated by an audible sig-
nal and a message on the multifunc-
tion screen.
Top up the level when you stop the
vehicle.
Coolant level
Coolant change
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
The coolant must conform to the
manufacturer's recommendations. The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tem-
perature of the coolant is regulated
by the fan. This can operate with the
ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h
a p a r t i c l e e m i s s i o n fi l t e r , t h e f a n
may operate after the vehicle has
been switched off, even if the en-
gine is cold.
In addition, as the cooling system is
pressurised, wait at least one hour
after switching off the engine before
carrying out any work.
To avoid any risk of scalding, un-
screw the cap by two turns to al-
low the pressure to drop. When the
pressure has dropped, remove the
cap and top up the level.
Page 202 of 314
XI
1 8 1
P R A C T I C A L I N F O R M A T I O N
FUSEBOX A Table of fuses
Fuse N° Rating
Function
G29 - -
G30 5 A H e a t e d d o o r m i r r o r s
G31 5 A Rain and brightness sensor
G32 5 A S e a t b e l t n o t f a s t e n e d w a r n i n g l a m p s
G33 5 A E l e c t r o c h r o m e r e a r v i e w m i r r o r
G34 20 A S u n r o o f ( s a l o o n )
G35 5 A P a s s e n g e r d o o r l i g h t i n g - p a s s e n g e r d o o r m i r r o r a d j u s t m e n t
G36 30 A E l e c t r i c t a i l g a t e ( t o u r e r )
G37 20 A Heated front seats
G38 30 A Driver’s electric seat
G39 30 A P a s s e n g e r ’ s e l e c t r i c s e a t - H I F I a m p l i fi e r
G40 3 A T r a i l e r r e l a y u n i t s u p p l y
FUSEBOX B
Fuse N° Rating
Function
G36
15 A 6 s p e e d a u t o m a t i c g e a r b o x
5 A 4 s p e e d a u t o m a t i c g e a r b o x
G37 10 A D a y t i m e - r u n n i n g l a m p s - D i a g n o s t i c s o c k e t
G38 3 A ESP
G39 10 A H y d r a u l i c s u s p e n s i o n
G40 3 A STOP switch
Page 210 of 314
XI
!
1 8 9
P R A C T I C A L I N F O R M A T I O N
TOWING A TRAILER, A CARAVAN, ETC.
T o w b a r s u i t a b l e f o r t h e a t t a c h m e n t
of a trailer or caravan with additional
l i g h t i n g a n d s i g n a l l i n g .
Y o u r v e h i c l e i s p r i m a r i l y d e s i g n e d
f o r t r a n s p o r t i n g p e o p l e a n d l u g g a g e ,
b u t i t m a y a l s o b e u s e d f o r t o w i n g a
t r a i l e r .
W e r e c o m m e n d t h e u s e o f g e n u i n e
C I T R O Ë N t o w b a r s a n d t h e i r h a r -
nesses that have been tested and
a p p r o v e d f r o m t h e d e s i g n s t a g e
o f y o u r v e h i c l e , a n d t h a t t h e fi t -
ting of the towbar is entrusted to a
C I T R O Ë N d e a l e r . I f t h e t r a i l e r i s n o t fi t t e d b y a
C I T R O Ë N d e a l e r , i t i s i m p e r a -
t i v e t h a t i t i s fi t t e d u s i n g t h e
e l e c t r i c a l p r e - e q u i p m e n t i n s t a l l e d
a t t h e r e a r o f t h e v e h i c l e , i n a c c o r -
d a n c e w i t h t h e m a n u f a c t u r e r ' s i n -
s t r u c t i o n s .
Driving with a trailer subjects the
t o w i n g v e h i c l e t o m o r e s i g n i fi c a n t
s t r e s s a n d i t s d r i v e r m u s t b e p a r -
t i c u l a r l y c a r e f u l .
Driving advice
Distribution of loads
Distribute the load in the trailer
s o t h a t t h e h e a v i e s t i t e m s a r e a s
c l o s e a s p o s s i b l e t o t h e a x l e a n d
t h e n o s e w e i g h t a p p r o a c h e s t h e
m a x i m u m p e r m i t t e d w i t h o u t e x -
c e e d i n g i t .
A i r d e n s i t y d e c r e a s e s w i t h a l t i t u d e ,
t h u s r e d u c i n g e n g i n e p e r f o r m a n c e .
A b o v e 1 0 0 0 m e t r e s , t h e m a x i m u m
t o w i n g l o a d m u s t b e r e d u c e d b y 1 0 %
a n d s o o n f o r e v e r y 1 0 0 0 m e t r e s o f
a l t i t u d e .
Refer to the "Technical Data" section
for details of the weights and towing
l o a d s w h i c h a p p l y t o y o u r v e h i c l e .
Side wind
Take into account the increased
s e n s i t i v i t y t o s i d e w i n d . Cooling
T o w i n g a t r a i l e r o n a s l o p e i n c r e a s e s
t h e t e m p e r a t u r e o f t h e c o o l a n t .
A s t h e f a n i s e l e c t r i c a l l y c o n t r o l l e d ,
i t s c o o l i n g c a p a c i t y i s n o t d e p e n d e n t
o n t h e e n g i n e s p e e d .
T o l o w e r t h e e n g i n e s p e e d , r e -
d u c e y o u r s p e e d .
T h e m a x i m u m t o w i n g l o a d o n a l o n g
s l o p e d e p e n d s o n t h e g r a d i e n t a n d
t h e a m b i e n t t e m p e r a t u r e .
I n a l l c a s e s , p a y a t t e n t i o n t o t h e
c o o l a n t t e m p e r a t u r e .
I f t h e w a r n i n g l a m p a n d
the STOP w a r n i n g l a m p
c o m e o n , s t o p t h e v e h i c l e
and switch off the engine
a s s o o n a s p o s s i b l e .
Braking
T o w i n g a t r a i l e r i n c r e a s e s t h e b r a k -
i n g d i s t a n c e .
Tyres
C h e c k t h e t y r e p r e s s u r e s o f t h e
t o w i n g v e h i c l e a n d o f t h e t r a i l e r ,
o b s e r v i n g t h e r e c o m m e n d e d
p r e s s u r e s .
Lighting
Check the electrical lighting and
s i g n a l l i n g o n t h e t r a i l e r .
T h e r e a r p a r k i n g s e n s o r s w i l l b e d e -
a c t i v a t e d a u t o m a t i c a l l y i f a g e n u i n e
C I T R O Ë N t o w b a r i s u s e d .