warning Citroen C5 2009.5 (RD/TD) / 2.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2009.5, Model line: C5, Model: Citroen C5 2009.5 (RD/TD) / 2.GPages: 314, PDF Size: 19.25 MB
Page 90 of 314
V
87
V I S I B I L I T Y
Linked with the automatic
"Guide-me-home" lighting
Link with the automatic illumination
of headlamps provides the "guide-
me-home" lighting with the following
additional options:
- selection of the duration of light- ing for 15, 30 or 60 seconds in
the vehicle parameters on the in-
s t r u m e n t p a n e l s c r e e n c o n fi g u -
ration menu,
- automatic activation of "guide- me-home" lighting when auto-
matic illumination of headlamps
is in operation.
Operating fault
In the event of a malfunction of the
brightness sensor, the lamps come
on and a message appears on the
instrument panel screen, accompa-
nied by an audible signal.
Consult a CITROËN dealer.
In fog or snow, the brightness
s e n s o r m a y d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lamps will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer operate.
MANUAL HEADLAMP ADJUSTMENT
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
-. Intermediate setting.
2. 5 people + maximum authorised
loads.
-. Intermediate setting.
3. Driver + maximum authorised
loads.
Initial setting is position "0".
AUTOMATIC ADJUSTMENT OF DIRECTIONAL HEADLAMPS
Do not touch the xenon bulbs.
Consult a CITROËN dealer.
If a malfunction occurs,
this warning lamp is dis-
played on the instrument
panel, accompanied by
an audible signal and a
message on the instru-
ment panel screen.
The system then places your head-
lamps in the lowest position.
To avoid causing a nuisance to oth-
er road users, this system corrects
the height of the xenon headlamp
beams automatically and when sta-
tionary, depending on the load in the
vehicle.
Page 92 of 314
V
87
V I S I B I L I T Y
Linked with the automatic
"Guide-me-home" lighting
Link with the automatic illumination
of headlamps provides the "guide-
me-home" lighting with the following
additional options:
- selection of the duration of light- ing for 15, 30 or 60 seconds in
the vehicle parameters on the in-
s t r u m e n t p a n e l s c r e e n c o n fi g u -
ration menu,
- automatic activation of "guide- me-home" lighting when auto-
matic illumination of headlamps
is in operation.
Operating fault
In the event of a malfunction of the
brightness sensor, the lamps come
on and a message appears on the
instrument panel screen, accompa-
nied by an audible signal.
Consult a CITROËN dealer.
In fog or snow, the brightness
s e n s o r m a y d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lamps will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer operate.
MANUAL HEADLAMP ADJUSTMENT
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
-. Intermediate setting.
2. 5 people + maximum authorised
loads.
-. Intermediate setting.
3. Driver + maximum authorised
loads.
Initial setting is position "0".
AUTOMATIC ADJUSTMENT OF DIRECTIONAL HEADLAMPS
Do not touch the xenon bulbs.
Consult a CITROËN dealer.
If a malfunction occurs,
this warning lamp is dis-
played on the instrument
panel, accompanied by
an audible signal and a
message on the instru-
ment panel screen.
The system then places your head-
lamps in the lowest position.
To avoid causing a nuisance to oth-
er road users, this system corrects
the height of the xenon headlamp
beams automatically and when sta-
tionary, depending on the load in the
vehicle.
Page 93 of 314
V
87
V I S I B I L I T Y
Linked with the automatic
"Guide-me-home" lighting
Link with the automatic illumination
of headlamps provides the "guide-
me-home" lighting with the following
additional options:
- selection of the duration of light- ing for 15, 30 or 60 seconds in
the vehicle parameters on the in-
s t r u m e n t p a n e l s c r e e n c o n fi g u -
ration menu,
- automatic activation of "guide- me-home" lighting when auto-
matic illumination of headlamps
is in operation.
Operating fault
In the event of a malfunction of the
brightness sensor, the lamps come
on and a message appears on the
instrument panel screen, accompa-
nied by an audible signal.
Consult a CITROËN dealer.
In fog or snow, the brightness
s e n s o r m a y d e t e c t s u f fi c i e n t l i g h t .
Therefore, the lamps will not come
on automatically.
Do not cover the brightness sen-
sor, linked with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer operate.
MANUAL HEADLAMP ADJUSTMENT
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
-. Intermediate setting.
2. 5 people + maximum authorised
loads.
-. Intermediate setting.
3. Driver + maximum authorised
loads.
Initial setting is position "0".
AUTOMATIC ADJUSTMENT OF DIRECTIONAL HEADLAMPS
Do not touch the xenon bulbs.
Consult a CITROËN dealer.
If a malfunction occurs,
this warning lamp is dis-
played on the instrument
panel, accompanied by
an audible signal and a
message on the instru-
ment panel screen.
The system then places your head-
lamps in the lowest position.
To avoid causing a nuisance to oth-
er road users, this system corrects
the height of the xenon headlamp
beams automatically and when sta-
tionary, depending on the load in the
vehicle.
Page 127 of 314
VIII
111
S A F E T Y
DIRECTION INDICATORS
Left: lower the lighting stalk be-
yond the point of resistance.
Right: raise the lighting stalk be-
yond the point of resistance.
"Motorway" function
P r e s s b r i e fl y u p w a r d s o r d o w n -
w a r d s , w i t h o u t g o i n g b e y o n d t h e
point of resistance; the direction
i n d i c a t o r s w i l l fl a s h 3 t i m e s .
HAZARD WARNING LAMPS
A v i s u a l w a r n i n g b y m e a n s o f t h e
direction indicators to alert other
r o a d u s e r s t o a v e h i c l e b r e a k d o w n ,
towing or accident.
Automatic operation of
hazard warning lamps
W h e n b r a k i n g i n a n e m e r g e n c y ,
depending on the deceleration, the
h a z a r d w a r n i n g l a m p s c o m e o n a u -
t o m a t i c a l l y .
T h e y s w i t c h o f f a u t o m a t i c a l l y t h e
fi r s t t i m e y o u a c c e l e r a t e .
Y o u c a n a l s o s w i t c h t h e m o f f b y
p r e s s i n g t h e b u t t o n . A u d i b l e w a r n i n g t o a l e r t o t h e r r o a d
u s e r s t o a n i m m i n e n t d a n g e r .
Selection of the left or right direction
indicators to signal a change of di-
rection of the vehicle.
P r e s s t h i s b u t t o n , t h e d i r e c t i o n
i n d i c a t o r s fl a s h .
They can operate with the ignition off.
Press the left or right-hand part
o f t h e fi x e d c e n t r e d c o n t r o l s
steering wheel.
U s e t h e h o r n m o d e r a t e l y a n d o n l y
in the following cases:
- i m m e d i a t e d a n g e r ,
- when approaching an area where there is no visibility.
Page 128 of 314
VIII
112
S A F E T Y
TYRE UNDER-INFLATION DETECTION
S y s t e m w h i c h a u t o m a t i c a l l y c h e c k s t h e
p r e s s u r e s o f t h e t y r e s w h i l e d r i v i n g . Tyres OK display
Choice of detection
T h i s f u n c t i o n p r o v i d e s w a r n i n g o f t y r e s
t h a t a r e u n d e r - i n fl a t e d o r p u n c t u r e d .
Automatic detection
S e n s o r s m o n i t o r t h e t y r e p r e s s u r e s .
I n t h e e v e n t o f a n a n o m a l y , a m e s -
s a g e w i l l a p p e a r o n t h e i n s t r u m e n t
panel screen.
Driver request detection
Y o u c a n c h e c k t h e t y r e p r e s s u r e s a t
a n y t i m e .
P r e s s o n b u t t o n A (CHECK); the
i n f o r m a t i o n w i l l b e d i s p l a y e d o n
t h e i n s t r u m e n t p a n e l s c r e e n .
P r e s s o n b u t t o n A (CHECK).
T h e s y s t e m i n d i c a t e s t o y o u t h a t t h e
t y r e s a r e c o r r e c t l y i n fl a t e d .
T h i s i n f o r m a t i o n i s o n l y a v a i l a b l e o n
t h e r e q u e s t b y t h e d r i v e r . Under-inflated tyre
automatic detection
detection on request
Automatic detection:
A m e s s a g e i n d i c a t e s w h i c h t y r e i s
u n d e r - i n fl a t e d .
Driver request detection:
T h e v e h i c l e o u t l i n e i n d i c a t e s t h e u n d e r -
i n fl a t e d t y r e ( s ) .
T h e m e s s a g e i s a c c o m p a n i e d b y
lighting of the SERVICE warning
l a m p a n d a n a u d i b l e b e e p .
C h e c k t h e t y r e p r e s s u r e s a s
soon as possible.
Page 140 of 314
IX
!
123
D R I V I N G
MANUAL PARKING BRAKE
Mechanical device for immobilising
the vehicle when stationary. This warning lamp comes
on if the parking brake is en-
gaged or not fully released.
If the parking brake is released,
the lighting of this warning lamp
along with the STOP warning lamp
i n d i c a t e s t h a t t h e b r a k e fl u i d l e v e l
is low or a malfunction of the brake
force distributor.
It is essential to stop the vehicle.
Consult a CITROËN dealer.
Application
Pull the parking brake lever up to
immobilise your vehicle.
To facilitate the action on the lever,
you are recommended to press the
brake pedal at the same time.
In all circumstances, as a pre-
cautionary measure, engage
fi r s t g e a r .
On steep gradients, turn the steer-
ing wheel towards the pavement. Release
Press on the end of the lever
whilst pulling it then lower it fully.
Page 141 of 314
IX!!
124
D R I V I N G
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the park-
ing brake
is automatically applied
when the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y :
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobil-
ise the vehicle you need to manually
apply the parking brake by pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
-
the display of a message "hand-
brake on" on the instrument panel
screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m
to you the application/release of
your electric parking brake.
- the lighting of warning
lamp P on control A and
on the instrument panel,
-
the display of a message "hand-
brake on" on the instrument panel
screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P on
the instrument panel is per-
manently lit.
Page 142 of 314
IX!
!
125
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox ( fi r s t
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
-
the display of a message "hand-
brake off" on the instrument panel
screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of
the automatic functions *
Automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
s c r e e n c o n fi g u r a t i o n m e n u . S e l e c t
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
Deactivation of the automatic
functions is recommended in
very cold weather (freezing) and
when towing (recovery, caravan...). Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply
the parking brake whether the engine
is running or off,
pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
-
the display of a message "hand-
brake on" on the instrument panel
screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and a
message displayed if the parking
brake has not been applied.
* Depending on country.
Page 143 of 314
IX!
!
125
D R I V I N G
Release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
with a manual gearbox ( fi r s t
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accelera-
tor pedal and move off.
with an automatic gearbox , ac-
celerate with the selector in posi-
tion D , M or R .
Full release of the parking brake is
c o n fi r m e d b y : - the warning lamp P on
control A and on the in-
strument panel going out,
-
the display of a message "hand-
brake off" on the instrument panel
screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake. Activation/Deactivation of
the automatic functions *
Automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation/deactiva-
tion is done in the instrument panel
s c r e e n c o n fi g u r a t i o n m e n u . S e l e c t
"Vehicle parameters/Comfort/Auto
handbrake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
Deactivation of the automatic
functions is recommended in
very cold weather (freezing) and
when towing (recovery, caravan...). Manual operation
Manual application/release of the
parking brake is always possible.
Application
With the vehicle stationary, to apply
the parking brake whether the engine
is running or off,
pull on control A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of the warning lamp on control A and of
warning lamp P on the in-
strument panel,
-
the display of a message "hand-
brake on" on the instrument panel
screen.
When the driver’s door is
opened with the engine run-
ning, a beep is heard and a
message displayed if the parking
brake has not been applied.
* Depending on country.
Page 144 of 314
IX!
126
D R I V I N G
Release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal,
push then release control A .
The full application of the parking
b r a k e i s c o n fi r m e d b y :
- the warning lamp on con- trol A and the warning
lamp P on the instrument
panel going off,
- the display of a message "park- ing brake released" on the instru-
ment panel screen.
If you push control A without pressing the brake pedal, the parking brake
will not be released and the message
"Apply foot on brake" will be dis-
played on the instrument panel.
When stationary, with the en-
gine running, do not press the
accelerator pedal unneces-
sarily, as you may release the
parking brake. Maximum application
If necessary, you can utilise
maxi-
mum application of the parking
brake. It is obtained by means of a
long pull on control A , until you see
the message "Max application of the
handbrake" and a beep is heard.
Maximum application is essential:
- in the case of a vehicle towing a caravan or a trailer, if the au-
tomatic functions are activated
but you are applying the parking
brake manually,
-
when the gradient you are parked on is variable in its effect (e.g. on
a ferry, in a lorry, during towing).
- in the case of towing, a loaded vehicle or parking on a gradient,
turn the front wheels towards the
pavement and engage a gear
when you park.
- after a maximum application, the release time will be longer. Particular situations
In certain situations (starting the en-
gine...), the parking brake can auto-
matically alter its level of application.
This is normal operation.
To advance your vehicle a few cen-
timetres without starting the engine,
but with the ignition on, press on the
brake pedal and release the parking
brake
by pushing then releasing
control A .
The full release of the parking brake
i s c o n fi r m e d b y t h e w a r n i n g l a m p P
(red) on the instrument panel going
off and the display of a message
"handbrake off" on the instrument
panel screen.
If the parking brake malfunctions
while applied o r i f t h e b a t t e r y i s fl a t ,
an emergency release is still pos-
sible.
To ensure correct operation of the
parking brake and therefore your
safety, the number of successive
application/release operations is
limited to eight.
If this number is exceeded, you are
warned by the message "Parking
brake faulty" and a warning lamp
fl a s h e s .