bonnet Citroen C5 2012 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2012, Model line: C5, Model: Citroen C5 2012 (RD/TD) / 2.GPages: 316, PDF Size: 9.75 MB
Page 5 of 316
CONTENTS
Direction indicators 114
Hazard warning lamps 114
Horn 114
Emergency or assistance call 114
Tyre under-infl ation detection 115
Braking assistance systems 117
Trajectory control systems 118
Seat belts 119
Airbags 122
VIII-SAFETY 11 4 Î125
Parking brake 126
Electric parking brake 127
Hill start assist 134
Manual gearbox 135
Gear shift indicator 136
6-speed electronic
gearbox system 137
Stop & Start 141
Automatic gearbox 144
Fixed centred controls
steering wheel 148
Speed limiter 150
Cruise control 152
Lane departure warning system 154
Parking space sensor 155
Parking sensors 157
Reversing camera (Tourer) 158
"Hydractive III +" electronic
suspension 159
IX - DRIVING 126 Î160
Bonnet 162
Running out of fuel (Diesel) 164
Petrol engines 165
Diesel engines 167
Checking levels 170
Checks 172
X -CHECKS 161 Î 173
Temporary puncture repair kit 174
Changing a wheel 177
Changing a bulb 181
Changing a fuse 191
Battery 196
Energy economy mode 198
Towing the vehicle 199
Towing a trailer 200
Roof bars 201
Very cold protection 202
Cold climate screen 203
Accessories 205
XI - PRACTICALINFORMATION 174 Î 206
Petrol engines 207
Petrol weights 208
Diesel engines 210
Diesel weights 212
Diesel weights -
commercial versions (Tourer) 216
Dimensions 217
Identifi cation markings 221
XII - TECHNICALDATAA 207 Î222
Emergency or assistance 223
eMyWay 225
Audio system 279
XIII - AUDIO andTELEMATICS 223 Î298
VISUALSEARCH 299 Î 304
ALPHABETICAL INDEX 305 Î 309
Page 8 of 316
6
FAMILIARISATION
The bonnet release should only be op-
erated when the vehicle is stationary.
)
Open the left hand front door.
)
Pull release lever A
to unlock the
bonnet.
Opening the bonnet
ACCESS
)
Lift safety catch B
, then raise the
bonnet.
Saloon
Tourer
Spare wheel
The tools are located in a protective
holder inside the spare wheel.
177
Access to the spare wheel
To access the spare wheel:
)
Saloon: raise the boot fl oor and fold
it in two.
)
Tourer: raise the boot fl oor and at-
tach it using the retractable grip.
Secure the hook to the upper part of
the boot.
)
To remove the spare wheel, detach
the strap then push the wheel for-
wards, before lifting it out.
Temporary puncture repair kit
The kit is a complete system comprised
of a compressor and a sealant car-
tridge.
174
162
Page 11 of 316
9
FAMILIARISATION
INSTRUMENTS AND CONTROLS
1.
Sunshine sensor.
2.
Soft diffusion air conditioning adjustment wheel.
3.
Passenger's airbag.
4.
Side window demist vent.
5.
Passenger's air vents.
6.
Bonnet release.
7.
Hazard warning lamps switch.
8.
Switch in the glove box:
- Passenger’s airbag activation/deactivation
9.
Glove box:
- Vehicle document storage
- Audio-video sockets
- Fusebox access fl ap
10.
ESP / Parking Sensors / Lane Departure Warning
System controls.
11 .
Suspension controls:
- Ground clearance adjustment
- Sport mode
12.
Armrest with cup-holder.
13.
Electric parking brake.
14.
Automatic gearbox SPORT/SNOW mode
controls.
15.
Ashtray with cigarette lighter.
16.
Gear lever.
17.
Storage.
18.
Audio and telematics system.
19.
Air conditioning controls.
20.
Storage.
21.
Multifunction screen.
22.
Emergency or assistance call controls.
Page 24 of 316
22
FAMILIARISATION
DRIVING SAFELY
Stop & Start
Going into engine STOP mode
The "ECO"
warning lamp comes
on in the instrument panel and
the engine goes into standby:
- with the 6-speed electronic gear-
box system
; at speeds below 4 mph
(6 km/h), press the brake pedal or
put the gear lever into position N
.
Going into engine START mode
You can deactivate the system at any
time by pressing the "ECO OFF"
button;
the button's warning lamp comes on.
The system is reactivated automati-
cally every time you start the engine
with the key.
Before refuelling or doing anything
under the bonnet, you must switch off
the ignition with the key. The "ECO"
warning lamp goes
off and the engine restarts:
- with the gear lever in position A
or
M
, release the brake pedal,
- or with the gear lever in position N
and the brake pedal released, move
to position A
or M
,
- or engage reverse.
In certain circumstances, the STOP
mode may not be available; the "ECO"
warning lamp fl ashes for a few sec-
onds, then goes off.
In certain circumstances, START mode
may be invoked automatically; the
"ECO"
warning lamp fl ashes for a few
seconds, then goes off.
141
142
Deactivation / Reactivation
142
Page 34 of 316
I
32
MONITORING
Warning and indicator lamps
Visual indicators which inform the driver of the occurrence of a malfunction or
fault (warning lamp) or of the operation of a system (operation or deactivation
indicator lamp).
Warning lamp
is on
Cause
Action / Observations
STOP
fi xed, associated
with another
warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer or a qualifi ed workshop.
Service
temporarily. A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter
(Diesel).
For any other faults, contact a CITROËN
dealer or a qualifi ed workshop.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen and contact a
CITROËN dealer or a qualifi ed workshop.
When the ignition is switched on
Certain warning lamps come on for a few seconds when the ignition is switched on.
When the engine is started, these warning lamps should go off.
If they remain on, before moving off, refer to the information for the warning lamp
concerned.
Associated warnings
The illumination, fi xed or fl
ashing, of certain warning lamps may be accompa-
nied by an audible signal and a message in the screen.
Warning lamps
When the engine is running or the
vehicle is being driven, the illumina-
tion of one of the following warning
lamps indicates a malfunction or
fault which requires action on the
part of the driver.
The illumination of a warning lamp is
always accompanied by the display
of an additional message, to assist
you in identifying the fault.
If you encounter any problems, con-
tact a CITROËN dealer or a qualifi ed
workshop.
Page 75 of 316
IV
!
73
ACCESS
ALARM *
System which protects and provides
a deterrent against theft and break-
ins. It provides the following types of
monitoring.
- exterior perimeter
The system checks for opening of
the vehicle.
The alarm is triggered if anyone tries
to open a door, the boot, the bonnet...
- interior volumetric
The system checks for any variation
in the volume in the passenger com-
partment.
The alarm is triggered if anyone breaks
a window, enters the passenger com-
partment or moves inside the vehicle.
- tilt
The system checks for any change
in the attitude of the vehicle.
The alarm is triggered if the vehicle
is lifted, moved or knocked.
Self-protection function
The system checks for the
putting out of service of its
components.
The alarm is triggered if the bat-
tery, the central control or the si-
ren wiring are put out of service or
damaged.
For all work on the alarm system,
contact a CITROËN dealer or a
qualifi ed workshop.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition and get out
of the vehicle.
)
Press the locking button on the
remote control.
The monitoring system is active: the
indicator lamp in the button fl ashes
once per second.
After the locking button on the re-
mote control is pressed, the exterior
perimeter monitoring is activated
after a delay of 5 seconds and the
interior volumetric and anti-tilt moni-
toring after a delay of 45 seconds.
If an opening (door, boot...) is not
closed fully, the vehicle is not locked
but the exterior perimeter monitor-
ing will be activated after a delay of
45 seconds at the same time as the
interior volumetric and anti-tilt moni-
toring.
Deactivation
)
Press the unlocking button on
the remote control.
The alarm system is deactivated: the
indicator lamp in the button goes off.
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
and anti-tilt monitoring to avoid un-
wanted triggering of the alarm in
certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea.
Deactivation of the interior
volumetric and anti-tilt
monitoring
)
Switch off the ignition.
)
Within ten seconds, press the
button until the indicator lamp is
on continuously.
)
Get out of the vehicle.
)
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring
alone is activated: the indicator lamp in
the button fl ashes once per second.
To be effective, this deactivation
must be carried out each time the
ignition is switched off.
*
According to country.
Page 145 of 316
IX
!
!
143
DRIVING
In the event of a fault with the sys-
tem, the "ECO OFF"
switch warning
lamp fl ashes then comes on con-
tinuously.
Have it checked by a CITROËN
dealer or a qualifi ed workshop.
In the event of a fault in STOP mode,
the vehicle may stall: all the instru-
ment panel warning lamps come on.
It is then necessary to switch off the
ignition and start the engine again
using the key.
Operating fault
The Stop & Start system
makes use of advanced tech-
nology. For any work on the sys-
tem go to a qualifi ed workshop with
the skills and equipment required,
which a CITROËN dealer is able to
provide.
Before doing anything under
the bonnet, deactivate the
Stop & Start system to avoid
any risk of injury resulting from au-
tomatic operation of START mode.
Maintenance
This system requires a 12 V battery
with a special specifi cation and tech-
nology (reference numbers available
from CITROËN dealers).
Fitting a battery not listed by
CITROËN introduces the risk of mal-
function of the system.
To charge the battery, use a 12 V
charger and observe the polarity.
Page 164 of 316
!
162
CHECKS
BONNET
Opening
)
At the front of the bonnet, lift the
safety catch B
and raise the bonnet.
)
Unclip the stay C
from its housing
and pivot it to insert it in the notch D
indicated by a yellow arrow.
)
Fix the stay in the notch to hold
the bonnet open.
Closing
)
Take the stay out of the support
notch.
)
Clip the stay in its housing.
)
Lower the bonnet then slam it
fi rmly at the end of its travel.
)
Pull on the bonnet to check that
it is fully closed.
When the engine is hot, handle the
safety catch and bonnet stay with
care (risk of burns).
The location of the interior release
lever prevents opening of the bon-
net while the left hand front door is
closed.
This operation must only be carried
out when the vehicle is stationary.
Avoid opening the bonnet in strong
winds.
)
Open the left hand front door.
)
Pull the interior bonnet release
lever A
, located at the bottom of
the door frame.
Before doing anything un-
der the bonnet, switch off the
Stop & Start system to avoid
any risk of injury resulting from an
automatic change to START mode.
Page 172 of 316
X
!
170
CHECKS
CHECKING LEVELS
Oil level
The check is carried out either
when the ignition is switched
on using the oil level indicator
on the instrument panel, or
using the dipstick.
This manual check will only be cor-
rect if the vehicle is on level ground
and the engine has been off for more
than 30 minutes.
It is normal to top up the oil level be-
tween two services (or oil changes).
CITROËN recommends that you
check the level, and top up if neces-
sary, every 3 000 miles (5 000 kms).
After topping up the oil, the check
when switching on the ignition with
the oil level indicator in the instru-
ment panel is not valid during the
30 minutes after topping up.
If a level drops signifi cantly, have
the corresponding system checked
by a CITROËN dealer or a qualifi ed
workshop.
Check all of these levels regularly
and top them up if necessary, unless
otherwise indicated.
Take care when working under the
bonnet, as certain areas of the en-
gine may be extremely hot (risk of
burns).
Engine oil change
Refer to the servicing booklet for
details of the interval for this opera-
tion.
In order to maintain the reli-
ability of the engine and emis-
sion control system, the use
of additives in the engine oil is
prohibited.
Oil specifi cation
The oil must be the correct grade
for your engine and conform to the
manufacturer's recommendations.
Brake fluid level
The brake fl uid level should
be close to the "MAX" mark.
If it is not, check the brake
pad wear.
Changing the fl uid
Refer to the servicing booklet for de-
tails of the interval for this operation.
Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations
and meet the DOT4 standard.
Power steering or power
steering and suspension
fluid level
For topping up, it is necessary
to go to a CITROËN dealer or
a qualifi ed workshop.
Dipstick
There are two marks on
the dipstick:
A
= max; never exceed
this level,
B
= min; top up the oil
level via the oil fi ller cap,
using the correct grade of
oil for your engine.
Page 193 of 316
XI
191
PRACTICAL INFORMATION
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of
the corresponding function.
The 2 fuseboxes are located below
the dashboard and under the bonnet.
Replacing a fuse
Before replacing a fuse, you should
ascertain the cause of the fault and
have it remedied. the numbers of the
fuses are indicated on the fusebox.
Replace the fuse that has blown
with one of the same rating (same
colour).
Use the special tweezer 1
placed on
the fl ap close to the fuseboxes.
Good
Failed
Tweezer 1
Fuses under the dashboard
Access to the fuses
)
open the glove box then unclip
the access cover.
Fusebox C
Fusebox A
Tweezer 1
Fusebox B