display Citroen C5 2015 (RD/TD) / 2.G Owner's Guide

74
C5_en_Chap03_ergo-et-confort_ed01-2014
2a-2b. Temperature adjustment Control via the manual controls3a-3b. A ir distribution
adjustment
F Press control 3b to change the distribution
of the air flow on the passenger's side.
The indicator lamps corresponding to the
distribution chosen come on:
-

W
indscreen and front side windows.
-

F
ront ventilation (central and side vents
and air diffusion grille if open) and rear
ventilation.
-

F
ront and rear footwells.
Simultaneous display of the distribution of air to
the windscreen and side windows and of front
and rear ventilation is not possible.
F

T

urn control 2a
to change the temperature
on the driver's side and control 2b
to change the temperature on the
passenger's side: to the right to increase
the temperature or to the left to reduce it.
The setting required is displayed.
The value indicated on the display corresponds
to a level of comfort and not to a temperature in
degrees Celsius or Fahrenheit, depending on
the screen configuration.
A setting around the value 21 usually provides
optimum comfort. However, depending on your
requirements, a setting between 18 and 24 is
normal.
On entering the vehicle, the interior
temperature may be much colder (or warmer)
than is comfortable. There is no need to
change the temperature displayed in order to
quickly obtain the level of comfort required.
The automatic regulation of the air conditioning
will use its maximum per formance settings to
correct the temperature difference as quickly
as possible. F

P
ress control 3a

to change the
distribution of the
air flow on the
driver's side.
F

P

ress one of the controls, with the
exception of temperature regulation 2a and
2b . The indicator lamps A in the "AUTO"
controls go off.
It is possible to adjust one or more functions
manually while leaving the other functions in
automatic mode.
Switching to manual mode may result in
discomfort (temperature, humidity, odour,
condensation) and may not provide optimum
comfort.
To return to "AUTO" mode, press controls 1a
and 1b . The indicator lamps A come on.
Ease of use and comfort

76
C5_en_Chap03_ergo-et-confort_ed01-2014
9. Front demisting - defrosting
In certain cases, the "AUTO"
mode may not be sufficient to
demist or defrost the windows
(humidity, several passengers,
i c e).
8. Rear demisting - defrosting
Switch off the rear screen and exterior mirrors
demisting when you consider this necessary
as low current consumption reduces fuel
consumption. The heated rear screen operates
independently of the air
conditioning system.
F Press control
8, with the engine running, to
demist the rear screen and the mirrors. The
indicator lamp comes on.
Demisting is switched off automatically to
avoid excessive consumption of current and
depending on the exterior temperature.
It may be stopped by pressing control 8 again
or when the engine is switched off.
In this latter case, the demisting resumes if the
engine is switched on again within one minute. F
P
ress control 9 to clear the windows
quickly. The indicator lamp comes on.
This system controls the temperature, air flow
and intake and distributes the ventilation to the
windscreen and front side windows.
Resuming manual control exits from the
"Demisting" mode. It must be cancelled as
soon as possible to permit renewal of the air in
the passenger compartment and demisting.
Pressing one of the controls 1a and 1b returns
the system to the "AUTO" mode.
With Stop & Start, when demisting has
been activated, the STOP mode is not
available. When starting with the engine cold,
air flow will reach its optimum level
gradually to prevent an excessive
distribution of cold air.
When entering the vehicle after it has
been parked for a fairly long period, if
the interior temperature is very different
from your comfort setting there is
no need to change the temperature
displayed in order to quickly reach the
level of comfort required. The system
automatically uses its maximum
per formance to correct the difference in
temperature as quickly as possible.
The water resulting from the air
conditioning condensation is discharged
via an opening provided for this purpose;
therefore, a puddle of water may form
underneath the vehicle when stationary.
In all seasons, if the weather is cool,
the air conditioning is useful as it
removes the humidity from the air
and the condensation. Avoid driving
for prolonged periods with the air
conditioning switched off.
Ease of use and comfort

77
C5_en_Chap03_ergo-et-confort_ed01-2014
Programmable heating
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats the coolant
circuit in order to benefit from an optimum
engine operating temperature from the time the
engine is switched on.
The programmable heating system is switched
on using the long range remote control.
Activation can be immediate or deferred by
means of a programming function.The heating system programming remote
control consists of the following buttons and
displays:
1.
S

crolling functions menu buttons.
2.
F

unction indicators: clock, temperature,
operating time, programmed time, heater
operation, heating management symbols.
3.
D

igital displays: time, temperature, duration
of operation, programmed time or level of
heating.
4.
O

ff button.
5.
O

n button.Displays on the remote
control screen
If a malfunction of the programmable
heating system occurs, contact a CITROËN
dealer or a qualified workshop .
Programming remote
control
3
Ease of use and comfort

78
C5_en_Chap03_ergo-et-confort_ed01-2014
Setting the time
Once the time has been displayed, by means
of the buttons 1, press buttons 4 and 5
simultaneously within 10 seconds.
Immediate activation
Press button 5 (ON) until the message "OK" appears.
When the signal has been received, the message
"OK" is displayed along with the duration of
operation.
This symbol flashes.
Set the time using the buttons 1 .
Press buttons 4 and 5 simultaneously to save it.
This symbol is displayed (fixed). The heater starts and this symbol is
displayed.
To deactivate the function, press button 4
(OFF) until the message "OK" appears.
This symbol is switched off.
Press the buttons 1 in succession to display the
functions.
The first press of the left-hand or right-hand
button displays the time.
Next, the left-hand button permits access to the
programming time then to the level of heating
(C1 to C5).
The right-hand button permits access to the
passenger compartment temperature then to
the duration of operation of the heater if it is to
be switched on immediately.
Displaying the functions
The passenger compartment temperature
information is only available when the engine is off.When carrying out these operations, if
the message
" F A I L" appears, the signal
has not been received. Repeat the
procedure after changing your location.
Ease of use and comfort

79
C5_en_Chap03_ergo-et-confort_ed01-2014
Press the buttons 1 to display the duration of
operation.
Setting the duration of
operation
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4 and 5
simultaneously within 10 seconds. This symbol flashes. Set the duration by pressing the buttons 1
(adjustment in steps of 10
mins and max value
30 mins).
Press buttons 4 and 5 simultaneously to save
the duration of operation.
This symbol is displayed (fixed).
The factory setting value is 30 minutes.
3
Ease of use and comfort

80
C5_en_Chap03_ergo-et-confort_ed01-2014
Programming the heating
Programming the departure time
Press the buttons 1 to display the programming
time.
Activation - deactivation
Once the programming time has been
displayed by means of the buttons 1, press
button 5 (ON) until the message "OK" appears.
This symbol is displayed.
Once the programming time has been
displayed, press buttons 4 and 5
simultaneously within 10 seconds. This symbol flashes.
Set the time by pressing the buttons

1 and
press buttons 4 and 5 simultaneously to save it.
This symbol is displayed (fixed). This symbol is displayed when the
heater starts. When the signal has been received,
the message "OK"
is displayed along
with the symbol "HTM" .
To deactivate the programming, press button 4
(OFF) until the message "OK" appears.
The symbol "HTM" is switched off.
You must programme your departure time in
order for the system to calculate the optimum
heater start time automatically.
HTM: Heat Thermo Management.
When carrying out these operations, if
the message " F A I L" appears, the signal
has not been received. Repeat the
procedure after changing your location.
Ease of use and comfort

81
C5_en_Chap03_ergo-et-confort_ed01-2014
Switching off the heating
Press button 5 (ON).The symbol "HTM" remains on.
Changing the level of heating
The system offers 5 levels of heating (from the
lowest level C1 to the highest level C5 ).
Once the level of heating has been displayed
by means of the buttons
1, press buttons 4 and
5 simultaneously.
The letter "C" flashes.
Set the level of heating by pressing the
buttons 1 .
Press buttons 4 and 5 simultaneously to save
the level selected. The letter "C" is displayed
(fixed). The factory pre-sets are replaced by the
new settings entered. The programmed
times are stored until the next time they
are changed.
When the departure time is activated,
the level of heating cannot be changed.
The departure time must be deactivated
first.
Changing the battery
The remote control is supplied by a
6V-28L battery, which is supplied.
Information on the display indicates when it is
time to replace this battery.
Unclip the casing then replace the battery.
The remote control must then be reinitialised,
see below.
Do not discard the used batteries, take
them to an approved collection point.
3
Ease of use and comfort

82
C5_en_Chap03_ergo-et-confort_ed01-2014
Reinitialising the remote control
If the vehicle's battery is disconnected or the
remote control's battery is replaced, the remote
control must be reinitialised.
After switching on the power, press button 4
(OFF) for 1 second within the next 5 seconds.
If the operation has taken place correctly the
message "OK" is displayed on the remote
control screen.
If a problem occurs, the message " F A I L"
appears. Repeat the operation. Always switch off the programmable
heating while filling with fuel to avoid
any risk of fire or explosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even for
short periods, in an enclosed space
such as a garage or workshop which
is not equipped with an exhaust gas
extraction system.
Do not park the vehicle on an
inflammable sur face (dry grass, dead
leaves, paper…), there is a risk of fire.
The programmable heating system
is supplied by the vehicle's fuel tank.
Before use, ensure that the quantity
of fuel remaining is sufficient. If the
fuel tank is at the reserve, we strongly
advise that you do not programme the
heating.
The interior volumetric protection alarm
movement sensor may be disturbed by
the flow of air from the programmable
heating when it is in operation.
To avoid any unexpected triggering
of the alarm during use of the
programmable heating, it is advisable
to deactivate the interior volumetric
protection.
An adaptation of your programmable
heating allows you to pre-heat your
vehicle's passenger compartment.
Contact a CITROËN dealer or a
qualified workshop.
Ease of use and comfort

143
C5_en_Chap05_visibilite_ed01-2014
Manual controls
Lamps off.
Automatic illumination of headlamps.
Sidelamps.Dipped headlamps or main
beam headlamps.
B.
S

talk for switching headlamps: pull
the stalk towards you to switch the
lighting between dipped and main beam
headlamps.
In the lamps off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
Displays
The lighting is controlled directly by the driver
by means of the ring A and the stalk B .A.
M

ain lighting mode selection ring: turn it
to position the symbol required facing the
mark.
C.
F
oglamps selection ring.
The foglamps operate with the sidelamps and
the dipped and main beam headlamps. Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
5
Visibility

99
C5_en_Chap04_conduite_ed01-2014
Do not flick the accelerator at the
moment of switching off the ignition.
This could cause serious damage to the
turbocharger(s).
Vehicles equipped with a
turbocharger
Never stop the engine without having allowed it
to run for a few seconds at idle, this being the
time required for the turbocharger to return to a
normal speed.Energy economy mode
After switching off the engine (position 1- Stop),
for a maximum of 30 minutes you can still use
functions such as the audio and telematic
system, the wipers, dipped beam headlamps,
courtesy lamps, ...
Switching off the engine
F Stop the vehicle.
F W ith the engine running at idle, turn the key
to position 1 .
F

R
emove the key from the ignition switch.
F

T
o lock the steering column, turn the
steering until it locks.
When you leave the vehicle, keep the
key with you and lock the vehicle. To facilitate unlocking of the steering
column, it is recommended that the
wheels be returned to the straight ahead
position before switching off the engine.
Never switch off the ignition before the
vehicle is at a complete stop. With the
engine off, the braking and steering
assistance systems are also cut off: risk
of loss of control of the vehicle. For more information, refer to the
"Practical information" section, under
"Energy economy mode".
F

C
heck that the parking brake is correctly
applied, particularly on sloping ground.
Key left in the "Ignition on"
position
On opening the driver's door, an alert
message is displayed, accompanied
by an audible signal, to remind you that
the key is still in the ignition switch at
position 1 (Stop) .
If the key has been left in the ignition
switch at position 2 (Ignition on) ,
the ignition will be switched off
automatically after one hour.
To switch the ignition back on, turn the
key to position 1 (Stop) , then back to
position 2 (Ignition on) .
4
Driving