battery Citroen C5 DAG 2008.5 (RD/TD) / 2.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5 DAG, Model: Citroen C5 DAG 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.85 MB
Page 66 of 306
80
4
A C C E S S
GLASS PANORAMIC ROOF (TOURER)
This device comprises a tinted glass
panoramic surface 1 to improve
brightness and vision in the passenger
compartment.
I t i s fi t t e d w i t h a n e l e c t r i c a l b l i n d 2
to help maintain a comfortable tem-
perature and reduce noise. Opening
Press control A .
Pressing to the 1st notch allows you
to open the blind step by step.
Pressing to the 2nd notch allows
you to fully open the blind.
The blind stops in the closest pre-
d e fi n e d p o s i t i o n ( 1 1 p o s i t i o n s ) a s
soon as you release the control.
Closing
Press control B .
Press to the fi r s t n o t c h to close the
blind step by step.
Press to the second notch to close
the blind completely.
The blind stops at the nearest pre-
set position (11 positions) as soon as
you release the control. After a battery disconnection, or if
there has been a malfunction, you
have to re-initialise the anti-pinch
function:
press control B to the 2 nd
notch
(fully closed),
wait until the blind is fully
closed,
press control B for at least 3 seconds.
If the blind opens randomly during a
closing operation, and straight after
the blind stops:
Press control B until the blind
closes fully.
During these operations, the anti-
pinch function does not operate.
In the event of anything being
caught when the blind is moving,
you must reverse the movement of
the blind. To do so, reverse the po-
sition of the control.
When the driver is operating the
blind, he or she must always make
sure that the passengers are not
preventing it from closing properly.
The driver must ensure that his pas-
sengers are using the blind correctly.
Pay special attention to children
when operating the blind.
Anti-pinch
If the blind meets an obstacle whilst
closing, it stops and opens partially
again.
You must re-initialise the anti-pinch
function within 5 seconds of the
blind stopping:
press control B until the blind is
fully closed (closing in steps of a
few centimetres).
SEQUENTIAL ELECTRICAL BLIND
Page 70 of 306
84
V I S I B I L I T Y
5
C. fog lamps selection ring.
The fog lamps operate with the side
lights and the dipped and main beam
headlamps.
- 1 st turn forwards: lighting of rear foglamps.
- 1 st turn rearwards: extinction of rear foglamps. - 1 st turn forwards: lighting of front
foglamps.
- 2 nd turn forwards: lighting of rear foglamps.
- 1 st turn rearwards: extinction of rear foglamps.
- 2 nd turn rearwards: extinction of front foglamps.
Model with rear foglamps
only
Model with front and rear
foglamps In good or rainy weather, both day
and night, the front fog lamps and
the rear fog lamps are prohibited.
In these situations, the power of
their beams may dazzle other driv-
ers. They should only be used in
fog or snow.
In these weather conditions, it is
your responsibility to switch on the
fog lamps and dipped headlamps
manually as the brightness sensor
m a y d e t e c t s u f fi c i e n t l i g h t .
Do not forget to switch off the front
fog lamps and the rear fog lamps
when they are no longer neces-
sary.
Lights on buzzer
The triggering of an audible signal
when a front door is opened warns
the driver that he has forgotten to
switch off his vehicle's lights, with
the ignition off and in manual lights
mode.
In this case, switching off the lights
stops the audible signal.
With the ignition off, if the dipped
headlamps remain on, they will
switch off automatically after thirty
minutes to prevent discharging of
the battery.
Page 94 of 306
98
6
L A Y O U T
BOOT LAYOUT (SALOON)
1. Battery for vehicles with V6 HDi
engine.
2. Pull strap (spare wheel storage).
3. Boot lamp.
4. 6 CD changer. Luggage securing rings
Use the 4 securing rings on the
b o o t fl o o r t o s e c u r e y o u r l u g g a g e .
F o r s a f e t y r e a s o n s , i n c a s e o f t h e
n e e d f o r s h a r p b r a k i n g , y o u a r e
a d v i s e d t o p l a c e h e a v y o b j e c t s a s
f a r f o r w a r d i n t h e b o o t a s p o s s i b l e .
Page 95 of 306
99
6
L A Y O U T
BOOT LAYOUT (TOURER)
1. Hook
A l l o w s y o u t o h o o k s h o p p i n g b a g s .
2. Torch
T o r e c h a r g e , r e t u r n i t t o i t s s t o r - age position.
3.
Storage net or Battery compart-
ment (for vehicles with V6 2.7 HDi
engine).
T h i s p r o v i d e s a c c e s s t o t h e b a t t e r y .
1. Luggage-cover blind
(see details on following page)
2. Luggage securing rings
Use the 4 stowing rings provided o n t h e b o o t fl o o r t o s e c u r e y o u r
loads.
For safety reasons in the event o f s h a r p b r a k i n g , y o u a r e a d -
v i s e d t o p l a c e h e a v y o b j e c t s a s
f a r f o r w a r d s a s p o s s i b l e .
3. Hooks
T h e s e a l l o w a c a r g o n e t t o b e fi t t e d (see details on following page).
1. Boot lamp
2. 12 V accessories socket
(100 W maximum)
C i g a r - l i g h t e r t y p e 1 2 v o l t s s o c k e t . It is located on the rear right-hand
t r i m , a n d i s s u p p l i e d f r o m t h e i g n i -
tion position.
3. Loading assistance
You can change the height of the v e h i c l e i n o r d e r t o m a k e l o a d i n g
or unloading easier.
4. Hook
A l l o w s y o u t o h o o k s h o p p i n g b a g s .
5. Storage net or 6 CD changer
Page 124 of 306
125
9
D R I V I N G
Release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal,
push then release control A .
The full application of the parking
b r a k e i s c o n fi r m e d b y : - the extinction of the warn-ing lamp on control A and
of warning lamp P on the
instrument panel,
- the display of a message "park- ing brake released" on the instru-
ment panel display.
If you push control A without press-
ing the brake pedal, the parking
brake will not be released and the
message "Foot on brake necessary"
will be displayed on the instrument
panel.
When stationary, with the
engine running, do not
press the accelerator pedal
unnecessarily, as you may
release the parking brake. Maximum application
If necessary, you can utilise
maxi-
mum application of the parking
brake. It is obtained by means of a
long pull on control A , until you see
the message "Max application of the
parking brake" and a beep is heard.
Maximum application is essential:
- in the case of a vehicle towing a caravan or a trailer, if the au-
tomatic functions are activated
but you are applying the parking
brake manually,
- when the gradient you are parked on is variable in its effect (e.g. on
a ferry, in a lorry, during towing).
- In the case of towing, a loaded vehicle or parking on a gradient,
turn the front wheels towards the
pavement and engage a gear
when you park.
- After a maximum application, the release time will be longer. Particular situations
In certain situations (starting the
engine...), the parking brake can
automatically alter its force. This is
normal operation.
To advance your vehicle a few cen-
timetres without starting the engine,
but with the ignition on, press on the
brake pedal and release the parking
brake
by pushing then releasing
control A .
The full release of the parking brake
i s c o n fi r m e d b y t h e e x t i n c t i o n o f
warning lamp P (red) on the instru-
ment panel and the display of a
message "parking brake released"
on the instrument panel display.
If the parking brake malfunctions
while applied or if the battery
r u n s fl a t , an emergency release is
always possible.
To guarantee correct operation of
the parking brake and therefore
your safety, the number of succes-
sive application/release operations
is limited to eight.
If this number is exceeded, you are
warned by the message "Parking
brake faulty" and a warning lamp
fl a s h e s .
Page 125 of 306
126
9
D R I V I N G
Dynamic emergency braking
In the event of a failure of the vehi-
cle’s main braking system or in an
exceptional situation (e.g. driver tak-
en ill, under instruction, etc) pull and
hold control A to stop the vehicle.
The electronic stability programme
(ESP) provides stability during dy-
namic emergency braking.
If the dynamic emergency braking
malfunctions, one of the following
messages will be displayed on the
instrument panel display:
- "Parking brake faulty".
- "Parking brake control faulty". If a failure of the ESP sys-
tem is signalled by the light-
ing of this warning lamp,
then braking stability is not
guaranteed. In this event, stability
must be assured by the driver by
repeating alternate "pull release" ac-
tions on control A .
The dynamic emergency
braking must only be used
in exceptional circum-
stances. Emergency unlocking
In the event of the electronic parking
brake malfunctioning or the battery
r u n n i n g fl a t , a n e m e r g e n c y m a n -
ual device can unlock the parking
brake.
Immobilise the vehicle, with the
e n g i n e r u n n i n g , b y e n g a g i n g fi r s t
gear (manual gearbox) or posi-
tion P (automatic gearbox), then
switch off the engine.
If it is impossible to immobilise the vehicle, do not action the
control and urgently contact a
CITROËN dealer.
Page 126 of 306
127
9
D R I V I N G
Fetch the vehicle chock located
in the boot.
Immobilise the vehicle by placing
the chock at the front or at the
rear of one of the rear wheels.
Open the lower compartment of
the centre armrest by pulling it.
Ensure that the cup holder B is
retracted.
Remove the rubber mat covering
the base of the armrest. This strap does not permit
application of the parking
brake.
To re-engage the electronic parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A until the park-
i n g b r a k e w a r n i n g l a m p ( ! ) fl a s h e s
on the instrument panel then give a
second long pull until this warning
lamp is lit permanently.
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
b r a k e h a s r e - e n g a g e d ( fl a s h i n g o f
the warning lamp (!) on the instru-
ment panel then warning lamp lit
permanently) to avoid damage to
the parking brake.
Take care not to allow moisture or
dust in the proximity of the diagnos-
tic socket D which is essential for
the maintenance of your vehicle.
Release the strap from its location C .
Pull the strap to release the
b r a k e . A l o u d k n o c k c o n fi r m s t h e
release of the brake.
Take care to put the strap
back in its location C correct-
ly. Otherwise, it will no longer
be possible to apply the brake.
Consult a CITROËN dealer.
Put the rubber mat back in place
on the base of the armrest.
Remove and stow the chock.
Page 128 of 306
129
9
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of messages "
Parking brake faulty "
and " Anti roll-back fault " and of the follow-
ing warning lamps:
and/or fl a s h i n g
- The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electronic parking brake:
Immobilise the vehicle and switch off the ignition
Pull the control lever for at least 5 seconds or un til maximum application.
Switch on the ignition and check that the electronic parkin g
brake warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electronic parking brake:
Switch on the ignition.
Push the control lever and hold it for approximately 3 seconds.
5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electronic parking brake and
dynamic emergency braking are unavailable.
6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl a s h i n g - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
Wait approximately 3 minutes.
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .
7 Battery fault - Lighting of the battery warning la
mp makes it essential to stop the
v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r v e h i c l e .
- Apply the electronic parking brake before switching off the en-
gine.
Page 153 of 306
153
10
C H E C K S
PETROL ENGINES
They allow you access for checking
t h e l e v e l o f t h e v a r i o u s fl u i d s a n d f o r
replacing certain components.
1. Screenwash and headlamp
wash reservoir.
2. P o w e r s t e e r i n g fl u i d r e s e r v o i r o r
power steering and suspension
fl u i d r e s e r v o i r .
3. Coolant reservoir.
4. Dipstick.
5. E n g i n e o i l fi l l e r c a p .
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
V e h i c l e s fi t t e d w i t h t h e 2.0i
16V e n g i n e m a y b e fi t t e d
with metal suspension. In
this case, a different power steer-
i n g fl u i d r e s e r v o i r i s fi t t e d .
1.8i 16V
2.0i 16V
Page 154 of 306
154
10
C H E C K S 3 litre V6 petrol engine
1. Screen wash and headlamp
wash reservoir.
2. P o w e r s t e e r i n g a n d s u s p e n s i o n
fl u i d r e s e r v o i r .
3. Engine coolant reservoir.
4. Engine oil gauge.
5. Engine oil topping-up.
6. B r a k e fl u i d r e s e r v o i r .
7. Battery.
8. A i r fi l t e r .
3.0i V6