Citroen C5 RHD 2015 (RD/TD) / 2.G Repair Manual

59
Electric adjustments
To adjust the electric seats, switch on the
ignition or start the engine if the vehicle has
gone into economy mode.
Seat adjustments are also possible for a short
period after opening one of the front doors or
switching off the ignition.
1.
A
djustment of the seat height and
angle, and longitudinal position
R

aise or lower the front of the control to
adjust the seat cushion angle.
R

aise or lower the rear of the control to
raise or lower the seat.
S

lide the control for wards or backwards to
move the seat for ward or back.
2.
A

djustment of the backrest angle
M

ove the control for wards or backwards to
adjust the backrest angle.
3.
A

djustment of the angle of the top of
the backrest
M

ove the control for wards or backwards to
adjust the angle of the top of the backrest. Before moving the seat backwards,
ensure that there is nothing that might
prevent the full travel of the seat, so
as to avoid the risk of of jamming the
seat caused by the presence of objects
on the floor behind the seat or rear
passengers. If the seat jams, stop the
movement immediately.
Move the control:
-

F
or wards or backwards to increase or
reduce the lumbar support.
-

U
pwards or downwards to raise or lower
the lumbar support zone.
4.
A

djustment of lumbar support
T

his function allows you to independently
adjust the height and level of lumbar
support.
3
Ease of use and comfort

60
Head restraint height and
angle adjustments on
electric seats
F To adjust the angle of the head restraint, push back or pull for ward section C of the
head restraint until you reach the desired
position.
F

T
o raise it, pull upwards.
F

T
o lower it, press on the control D to unlock
it, and simultaneously on the head restraint
itself.
F

T
o remove it, press on the control D
to
unlock it, then pull it upwards.
Heated seats control
With the engine running, the front seats can
operate separately.
F
U
se the corresponding adjustment dial,
placed on the outer side of each front seat,
to switch on and select the level of heating
required:
0: Off.
1 : Low.
2 : Medium.
3 : High. This function provides the driver with a back
massage. It only operates when the engine is
running.
F

P
ress on button A.
The warning lamp comes on and the massage
function is activated for a period of 1 hour.
During this time, massage is per formed in
cycles of 6
minutes (4 minutes of massage
followed by 2 minutes break). In total, the
system will per form 10 cycles.
After 1 hour, the function is deactivated.
The
warning lamp goes out.
Massage function
Deactivation
You can deactivate the massage function at
any time by pressing on button A.
Ease of use and comfort

61
Storing driving positions
System which stores the settings of the driver's
seat. Up to two positions can be stored using
the buttons on the side of the driver's seat.
When storing a driving position, the air
conditioning settings are also memorised.
Storing a position
Using buttons M / 1 / 2
F Switch on the ignition.
F A djust your seat.
F

P
ress button M , then press button 1 or 2
within four seconds.
A

n audible signal confirms that the settings
have been stored.
Storing a new position cancels the previous
position.
Welcome function
The welcome function assists entry and leaving
the vehicle.
After switching off the ignition and opening
the driver’s door, the seat moves back
automatically and then stays in this position,
ready for the next entry to the vehicle.
When switching on the ignition, the seat moves
for ward to the memorised driving position.
When moving the seat, take care that no
person or object hinders the automatic
movement of the seat.
This function is deactivated by default. You may
activate or deactivate this function using the
"Main Menu" on the instrument panel screen.
To do so, select " Vehicle parameters/Comfort /
Driver welcome".
To adjust the air conditioning, refer to
the "Air conditioning" section.For your safety, avoid storing a driving
position while driving.
Recalling a stored position
Ignition on or engine running
F briefly press button 1 or 2 to recall the
corresponding position.
A

n audible signal indicates the end of the
adjustment.
When the ignition is on, after a few consecutive
position recalls, the function will be deactivated
until the engine is started, to prevent
discharging of the battery.
3
Ease of use and comfort

62
Steering wheel adjustment
F First, adjust the driver's seat to the most suitable position.
F

W
hen stationary , lower the lever A to
release the steering wheel adjustment.
F

A
djust for height and reach.
F

R
aise the lever to lock the steering wheel
adjustment.
After locking, if you press firmly on the steering
wheel, a slight click may be heard. The steering wheel can be adjusted for height and reach to adapt the driving position to the size of
the driver.
Adjustment
as a safety precaution, these
operations must only be carried out
while the vehicle is stationary.
Ease of use and comfort

63
Mirrors
Each fitted with an adjustable mirror glasses
providing the lateral rear ward vision necessary
for overtaking or parking. They can also be
folded.
Adjustment
With the ignition on:
F m ove control A to the right or to the left to
select the corresponding mirror,
F

m
ove control B in all four directions to
adjust,
F

r
eturn control A to the central position.
Folding
F from outside; lock the vehicle using the remote control or the key.
F

f
rom inside; with the ignition on, pull
control A rearwards.
If the mirrors are folded using control A , they
will not unfold when the vehicle is unlocked.
Control A must be pulled again.
Unfolding
F from outside; unlock the vehicle using the remote control or the key.
F

f
rom inside; with the ignition on, pull
control A rearwards.
If the position is changed manually, a long
press on control A re-engages the mirror.
The folding and unfolding of the door mirrors
using the remote control can be deactivated by
a CITROËN dealer or a qualified workshop.
Door mirrors
The objects observed are, in reality,
closer than they appear.
Take this into account in order to
correctly judge the distance of vehicles
approaching from behind.
Demisting/defrosting of the door mirrors
is associated with that of the rear
screen.
3
Ease of use and comfort

64
Automatic day/night model
In order to guarantee optimum visibility
during your manoeuvres, the mirror lightens
automatically when reverse gear is engaged. By means of a sensor, which measures the
light from the rear of the vehicle, this system
automatically and progressively changes
between the day and night uses.
It has an anti-dazzle system which darkens the
mirror glass: this reduces any driver discomfort
caused by the light beam of following vehicles,
the sun...In vehicles fitted with electrochromatic door
mirrors, the system has an on/off button and an
associated warning lamp.
On
F With the ignition on, press on button 1
.
The warning lamp 2 comes on and the mirror
glass is in automatic mode.
Off
F Press on button 1 .
The warning lamp 2 goes off and the mirror
glass remains in its lightest definition.
Rear view mirror
Manual day/night model
Adjustment
F Adjust the mirror so that the glass is directed correctly in the "day" position.
Day / night position
F Pull the lever to change to the "night" anti-dazzle position.
F

P
ush the lever to change to the normal
"day" position. As a safety measure, the mirrors should
be adjusted to reduce the "blind spot".
Adjustable mirror providing a central rear ward view.
Equipped with an anti-dazzle system, which darkens the mirror glass and reduces the nuisance to
the driver caused by the sun, headlamps from other vehicles...
Ease of use and comfort

65
Rear seats
Bench seat, the left-hand (2/3) or right-hand (1/3) section of which can be folded to adapt the boot load space.
F
M
ove the corresponding front seat for ward
if necessary.
F

R
aise the front of the seat cushion 1 .
F

T
ilt the seat cushion 1 fully against the front
seat.
F

R
emove the seat cushion 1 from its fixings
by pulling upwards.
Refitting the seat cushion
F Position the seat cushion 1 vertically in its fixings.
F

F
old down the seat cushion 1 .
F

P
ress on the seat cushion to secure it.
Removing the seat cushion
3
Ease of use and comfort

66
Rear head restraints
The rear head restraints can be removed and
have two positions:
-
h
igh, position for use,
-

l
ow, storage position.
To raise a head restraint, pull it upwards.
To lower it, press the lug then the head
restraint.
To remove it, place it in the high position, push
the lug and pull it upwards.
To refit it, engage the head restraint rods in the
holes taking care to remain in line with the seat
back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Returning the seat backrest
to its original position
When returning the rear seat to its original position:
F put the seat backrest 2 in the upright position and
secure it,
F fold the seat cushion 1 ,
F
refit the head restraints or put them back in place.When returning the rear seat to its original
position, take care not to trap the seat belts and
ensure that their buckles are positioned correctly.
The red indicator on the control 3 should no
longer be visible; if it is, push the seat fully
back.
Folding the seat
In order to fold a rear seat without any risk of
damage, always start with the seat cushion,
never with the seat backrest :
F

m
ove the corresponding front seat for ward
if necessary,
F

r
aise the front of the seat cushion 1 ,
F

t
ilt the seat cushion 1 fully against the front
seat,
F

c
heck that the seat belt is positioned
correctly on the side of the seat backrest,
F

l
ower or remove the head restraints if
necessary,
F

p
ull the control 3 for ward to release the
seat backrest 2 ,
F

t
ilt the seat backrest 2 .
The seat cushion 1 can be removed to increase
the load volume.
Ease of use and comfort

67
Ventilation
A. Sunshine sensor.
B.
S
oft air diffusion grille.
T

he soft air diffusion grille located in the
centre of the dashboard provides optimum
distribution of the air for the front seats.
T

his system eliminates unpleasant
air currents while maintaining an
optimum temperature in the passenger
compartment.
T

o open the soft air diffusion grille, turn the
wheel upwards.
T

o close the soft air diffusion grille, turn the
wheel fully downwards.
I

n very hot weather, to obtain more
satisfactory central and side ventilation, it
is advisable to close the diffused air grille.
C.
C

ooled glove box.
D.
R

ear passenger vents.
3
Ease of use and comfort

68
We recommend use of the automatic regulation
of the air conditioning.
It permits automatic and optimised control
of all of the following functions: air flow,
temperature in the passenger compartment
and air distribution, by means of various
sensors (ambient temperature, sunshine).
This eliminates any need for you to change
your settings other than the temperature value
displayed.
F Take care not to cover the sunshine sensor A .
If you select the automatic mode
(by pressing the "AUTO" control) and leave
all of the vents open, optimum comfort will be
maintained and humidity and condensation will
be removed regardless of the exterior climatic
conditions.
The temperature in the passenger compartment
can only be lower than the ambient temperature
if the air conditioning is on.
In order to be effective, the air conditioning must
be used with the windows closed. If the vehicle
has been parked in the sun for a long period and
the interior temperature is very high, first ventilate
the passenger compartment with the windows
open for a few minutes, then close the windows.
Heating, ventilation and air conditioning recommendations
To keep the air conditioning system in
good working order it is essential that it is
operated at least once a month.
The air conditioning uses engine power
during its operation. As a result, the fuel
consumption of the vehicle increases.
In certain cases of particularly arduous use
(e.g. towing the maximum load on a steep
gradient in high temperatures), switching off
the air conditioning saves engine power and
improves the towing capacity.
Air inlet
Check that the exterior grille for the air inlet,
at the bottom of the windscreen, is clean and
free of dead leaves, snow, etc.
When washing the vehicle using a high
pressure nozzle, avoid spraying at the air
inlet. Maximum comfort is obtained by means of
a good distribution of air in the passenger
compartment, both in the front and in the rear.
To obtain a uniform distribution of air, take
care not to block the exterior air intake grille
located at the base of the windscreen, the
vents, the air outlets under the front seats and
the air extractor located behind the flaps in
the boot.
The front and rear vents are fitted with
thumbwheels to adjust the air flow and
direction. We recommend that you leave all of
the vents open.
Dust filter / Odour filter
(active carbon)
There is a filter for excluding odours and
dust.
This filter must be changed in line with the
vehicle's servicing schedule. (Refer to the
maintenance and warranty guide).
Air conditioning
Air circulation
Ease of use and comfort