display CITROEN C6 2005 Owners Manual

Downloaded from www.Manualslib.com manuals search engine 8
GENERAL
OPERATIONS TO BE CARRIED OUT BEFORE AND AFTER A DISCONNECTION OF THE BATTERY
Before reconnecting the battery
.
Doors and tailgate.
WARNING: Before disconnecting the battery, partially open the door
windows.
Automatic gearbox.
If the vehicle has to remain stationary: Pplace the gear lever in the parking
position "P".
If the vehicle has to be moved: Place the gear lever in the neutral position
"N".
Electric parking brake.
If the vehicle has to remain stationary: Activate the electric parking brake.
If the vehicle has to be moved: Deactivate the electric parking brake.
Features of the vehicle's electrical supply.
When the boot is closed and the battery is disconnected, it is possible to
supply the vehicle by connecting another battery or a 12Vexterior supply.
Operations to be performed:
- Link the earth of the exterior supply to the vehicle earth.
- Link the 12Vof the exterior supply to the positive terminal of the battery +
unit, in the front left hand side of the engine compartment.
After reconnecting the battery
.
Antiscanning function.
It is necessary to wait 1 minuteafter reconnecting the battery in order to be
able to restart the vehicle.
Electric windows.
It may be necessary to re-initialise the sequential and anti-pinch functions.NOTE:If the window is open at the time the battery is reconnected, action
the window switch several times to close it, then re-initialise.
Open the window fully.
Action and release the window switch until the window is completely closed.
NOTE:This operation has to be carried out on each electric window.
Sun roof.
The anti-pinch function has to be re-initialised.
Place the sun roof switch in the maximum tilt position.
Keep the sun roof switch pressed until the sun roof ceases its movement.
Release the sun roof switch.
Press the sun roof switch within 5 seconds.
Keep the sun roof switch pressed until the end of the sun roof opening
sequence.
Multifunction screen.
It is necessary to adjust the date, time and outside temperature.
Adjust the display language of the multifunction screen if necessary.
NOTE:The default display language of the multifunction screen is French.
Reconfigure the personalisation menu of the multifunction screen.
Radio.
Reprogramme the radio stations.
Telematic control unit (RT3 radiotelephone).
Reprogramme the radio stations.
Navigation.
Warning: the vehicle has to be out in the open (when you switch on
the ignition, the navigation ECU searches for satellites).
Reprogramme the customer parameters.
Angl-C6-page001-21-2005 4/02/05 17:12 Page 8

Downloaded from www.Manualslib.com manuals search engine 101
CLUTCH
GEARBOX
TRANSMISSION
SPEEDOMETER
An E.E.C. decree of 25 June 1976, regulates the speed displayed by the speedmeter in relation to the actual speed travelled.
This decree stipulates:
- The speed indicated by a speedometer must never be lower than the actual vehicle speed.
- Between the speed displayed «SD»and the speed travelled «ST», there must always be the following relationship:
ST < SD < 1.10 ST + 4 Kph
Example:For an actual speed of 100 Kphthe speed displayed by the speedometer may be between 100and 11 4 K p h.
The speed indicated by the speedometer may be influenced by:
- The speedometer.
- The tyres fitted to the vehicle.
- The final drive ratio.
- The speedometer drive ratio.
Any of these components can be checked without removing them from the vehicle (see information note N° 78-85 TT of 19 October 1978).
NOTE:Before replacing the speedometer, check the conformity of the following points:
- The tyres fitted to the vehicle.
- The gearbox final drive ratio.
- The speedometer drive ratio.
Angl-C6-page101-120-2005 4/02/05 17:25 Page 101

Downloaded from www.Manualslib.com manuals search engine 201
HYDRAULICS
DE-PRESSURISING THE HYDRAULIC SUSPENSION CIRCUITTools.
[1] PROXIAstation: 4165-T
[2] LEXIAstation: 4171-T
De-pressurisation.
NOTE:It is possible to de-pressurise the suspension by individual axle.
Using a diagnostic tool.
Start the engine.
Place the height control in the «LOW»position.
Wait for the vehicle height to reach the position required.
Stop the engine.
Connect the diagnostic tool [1]or [2]to the vehicle's diagnostic socket.
Switch on the ignition.
Carry out a global test.Go into the menu:
- Suspension.
- De-pressurisation.
Follow the instructions displayed on the screen.
Wait for the vehicle's suspension to sink completely.
NOTE:This operation takes around 3 minutes.
Switch off the ignition.
Disconnect the battery.
Without a diagnostic tool.
IMPERATIVE: Any LDS fluid that is collected must not be re-used.
NOTE:Collect the LDSfluid in order to keep the work area clean.
Respect the environment.
Start the engine.
Place the height control in the «LOW»position.
Stop the engine.
Angl-C6-page195-202-2005 4/02/05 17:36 Page 201