tyre pressure Citroen C6 2007 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2007, Model line: C6, Model: Citroen C6 2007 1.GPages: 216, PDF Size: 7.57 MB
Page 1 of 216
I
4
IN BRIEF
E X T E R I O R
113
81
77
657980
Glass sun roof
The sun roof provides you with improved ventilation and brightness in the passenger compartment.
P i l o t e d D e fl e c t o r
T h i s d e fl e c t o r e n h a n c e s the aerodynamics and the braking of your vehicle.
Parking assistance (dis-play and sound)
This function warns you, whilst manoeuvring, by detecting obstacles located in front of and behind the vehicle.
Lane Departure Warning System
This driving assistance device warns you when you unwittingly cross a lane marking.
The Xenon dual-function directional headlamps
This additional lighting automati-cally provides you with enhanced visibility on bends.
T y r e d e fl a t i o n d e t e c t i o n
This function monitors the pressure of each tyre and warns you of tyres that a r e p u n c t u r e d o r d e fl a t e d .
Page 59 of 216
62
II
T R I P C O M P U T E R
OPERATION
For selection and display of the various types of information, give short presses on the end of the windcsreen wiper stalk.
Press on the “TRIP” button on the radio panel, for permanent display of the trip computer information.
To reset the trip computer infor-mation to zero, keep the end of the control stalk pressed for a few seconds when you see the relevant information displayed.
The trip computer gives you access to:Three types of instantaneous information:
Range.Instantaneous consumption.Distance remaining to be travelled.Three types of information for two Journeys 1 and 2:The distance travelled.Average consumption.Average speed.The JourneysJourneys 1 and 2 are independent of each other but identical in use. For example you can allocate Journey 1 to daily calculations and Jour-ney 2 to monthly calculations.Resetting a Journey to zeroWhen the desired Journey is displayed, give a long press on the end of the wiper control stalk.Information concerning your vehicle
The o i l t e m p e r a t u r e ( f o r N a v i D r i v e d i s p l a y o n l y ) .The coolant temperature.The tyre pressures.
Page 63 of 216
66
II
T R I P C O M P U T E R
T y r e d e fl a t i o n a l e r t
The SERVICE warning lamp comes on and a vehicle outline is displayed.
T h e l o c a t i o n o f t h e w h e e l ( s ) c o n c e r n e d i s c l e a r f r o m t h e v e h i c l e o u t l i n e , o n w h i c h t h e a f f e c t e d w h e e l ( s ) w i l l b e fl a s h -ing. Check the tyre pressures as soon as possible.
Colour screen CNaviDrive colour display
T y r e v e r y d e fl a t e d
T y r e d e fl a t e d
Stop immediately, avoiding any sudden actions with the steering wheel or the brakes.
C h a n g e t h e w h e e l w i t h t h e a f f e c t e d t y r e ( w h e t h e r p u n c t u r e d o r v e r y d e fl a t e d ) , t h e n h a v e t h e t y r e r e p a i r e d a n d all the pressures checked at the earliest opportunity.
The wheel with a damaged tyre (either in the boot or under repair) can no longer be detected (information given by the vehicle outline or by a message) nor is the spare wheel able to be detected.
Puncture
The « STOP » a n d t y r e ( s ) p u n c t u r e d w a r n i n g l a m p s l i g h t u p , a n d a v e h i c l e o u t l i n e i s d i s p l a y e d . T h e l o c a t i o n o f t h e w h e e l ( s ) c o n c e r n e d i s c l e a r f r o m t h e v e h i c l e o u t l i n e , o n w h i c h t h e a f f e c t e d w h e e l ( s ) w i l l b e fl a s h i n g .
Colour screen CNaviDrive colour display
Page 64 of 216
67
II
T R I P C O M P U T E R
Wheel not detected
The SERVICE warning lamp comes on and a vehicle outline is displayed.
T h e w h e e l ( s ) c o n c e r n e d c a n b e i d e n t i fi e d f r o m t h e v e h i c l e o u t l i n e , o n w h i c h i t ( t h e y ) w i l l b e m i s s i n g . I f y o u h a v e n o t changed a wheel, such information indicates that the system is malfunctioning.
C o n t a c t a C I T R O Ë N d e a l e r t o h a v e t h e f a u l t y s e n s o r ( s ) r e p l a c e d .
Colour screen CNaviDrive colour display
T h e d e fl a t i o n d e t e c t i o n s y s t e m i s a d r i v i n g a i d , b u t w h i c h d o e s n o t a b s o l v e t h e d r i v e r f r o m t h e n e e d t o b e v i g i l a n t a n d responsible.
T h i s s y s t e m d o e s n o t d i s p e n s e w i t h t h e r e q u i r e m e n t t o c h e c k t h e t y r e s o n a r e g u l a r b a s i s ( s e e “ V e h i c l e i d e n t i fi c a - t i o n ” ) , t o m a k e s u r e t h a t t h e v e h i c l e i s b e h a v i n g c o r r e c t l y a n d t o a v o i d p r e m a t u r e t y r e w e a r a r i s i n g f r o m d r i v i n g t o o fast etc.
Do not forget to check the pressure in the spare wheel.
Any repair or replacement of a tyre on a wheel that is equipped with a sensor must be carried out b y a C I T R O Ë N d e a l e r .Any repair or replacement repair or
The system may suffer from temporary interference caused by radio transmissions on neighbouring frequencies.
Page 153 of 216
156
VI
4
3
8
9
61
2
5
7
C H A N G I N G A W H E E L
ACCESS TO THE SPARE WHEEL
To access the spare wheel1. L i f t t h e b o o t fl o o r b y m e a n s o f t h e s t r a p .2. Anchor the strap on the roof of the boot.3. To remove the spare wheel, detach the belt then push the wheel for-wards so as to be able to lift it.
TO REPOSITION THE SPARE WHEEL
To put the spare wheel back in the boot1. P o s i t i o n t h e s p a r e w h e e l fl a t i n t h e b o o t , t h e n p u l l i t t o w a r d s y o u .2. Next place the toolbox inside the wheel, then secure the a ssembly with the belt.3. R e l e a s e t h e s t r a p t o r e t u r n t h e b o o t fl o o r t o i t s i n i t i a l p o s i t i o n .
Tyre pressures
Tyre pressures are indicated on the label which is positioned l ow down on t h e f r o n t p i l l a r . S e e “ V e h i c l e i d e n t i fi c a t i o n ” a n d “ U s e r P r e c a u t i o n s ” . ( O n t h i s label you will see a pressure for normal speeds and a pressure for high s p e e d s ) .
1. Handle2. Jack3. T o o l f o r r e m o v i n g / r e fi t t i n g t h e wheel bolts4. Tool for removing the anti-theft bolt protector5. Centring guide6. Tool for removing foglamps and reversing lamps7. Handle extension8. Towing eye9. Movable chock
TOOLS
The tools are to be found in a pro-tective holder inside the spare wheel. Pull back the retaining strap to have access.
Page 155 of 216
158
VI
It is essential not to exceed a speed of 80 km/h (50 mph) on your spare wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e t y p e o f w h e e l .
I f t h e t y p e o f w h e e l i s c h a n g e d , c h e c k w i t h y o u r C I T R O Ë N d e a l e r that the wheel bolts are compatible with the new wheels.
Note: take care to note down the code number engrav ed on the head of the anti-theft bolt socket. This will enable you to obtain replacement anti-theft bolt sockets from a dealership.
WHEEL FOR TEMPORARY USE
If your vehicle is equipped with a spare wheel for temporary use o n l y , w h e n fi t t i n g i t i t i s n o r m a l t o observe that the wheel bolts do not come to bear on the wheel rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft. See illustration.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l , ensure that the wheel bolt contact surfaces are clean and in good condition.
REFITTING A WHEEL1. Fit the wheel on the hub, using the centring guide. Make sure that the contact surface between the hub and the wheel is clean.2. Screw in the bolts but do not fully tighten them.3. Lower the jack and remove it.4. Tighten the wheel bolts, using the wheelbrace.5. R e fi t t h e e m b e l l i s h e r .6. Return the ground clearance to the normal position. See “Adjusting ground clearance”.7. Ensure the tyre pressure is c o r r e c t ( s e e “ V e h i c l e i d e n t i fi c a - t i o n ” ) a n d h a v e t h e b a l a n c i n g checked.
WHEEL EQUIPPED WITH DEFLATION DETECTION SENSOR
Such wheels have tyre pressure sensors. It is essential to have repairs carried out by a CITROËN dealer.
ANTI-THEFT BOLTS
Each wheel is equipped with one anti-theft bolt.
To remove it1. Remove the protector that is covering it by means of the tool 4 for “removing anti-theft protectors”.2. Use the anti-theft socket with the handle.
C H A N G I N G A W H E E L
Page 161 of 216
164
VII
BC
12345
A
AD
V E H I C L E I D E N T I F I C A T I O N
A Chassis number plateOn the left hand door centre pil-lar.
1. EU type approval number.2. V e h i c l e i d e n t i fi c a t i o n N o . ( V I N ) .3. Gross vehicle weight.4. Gross train weight.5. Maximum weight on front axle.6. Maximum weight on rear axle.B Body serial numberC Serial number on dashboardD Paint colour code Tyre reference Tyre pressuresOn front pillar.
T h e v e h i c l e t y p e a n d t h e i d e n t i fi c a t i o n n u m b e r a r e a l s o i n d i c a t e d o n t h e r e g i s t r a t i o n d o c u m e n t .
All CITROËN original replacement parts are available exclusively w ithin the dealer network.
For your safety and in order to remain within the terms of the guarantee, you are advised to use only CITROËN replacement parts.