seats Citroen C6 DAG 2007 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2007, Model line: C6 DAG, Model: Citroen C6 DAG 2007 1.GPages: 216, PDF Size: 7.61 MB
Page 8 of 216
II
1111
A
B
C
EFD
G21
IN BRIEF
FRONT SEATS
C. Adjustment of the backrest angle.
D. Adjustment of the backrest lum-bar support.
E. Seat height and slide adjust-ments.
F. Adjustment of the seat cushion angle.
G. Memorisation of dashboard adjustments:
- Driver's seat.
- Steering wheel.
- Exterior rear view mirrors.
- Head-up display.
You have the possibility to mem-orise two driving positionsusing buttons 1 and 2.
ELECTRICAL ADJUSTMENTS
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
MANUAL STEERING COL-UMN ADJUSTMENT
A. Adjustment of the backrest angle.
B. Controls for the heated seats.
282927
G E T T I N G S T A R T E D
Page 17 of 216
I
20
12
3
IN BRIEF
SEAT BELTS WARNING LAMPTYRE DEFLATION DETECTION
T h i s f u n c t i o n w a r n s y o u o f t y r e s t h a t a r e d e fl a t e d o r p u n c t u r e d .
T y r e d e fl a t i o n a l e r t : The SERVICE warning lamp comes on and a vehicle outline is displayed.
“Puncture”: The “STOP” a n d t y r e ( s ) p u n c t u r e d w a r n i n g l a m p s l i g h t u p , a n d a vehicle outline is displayed.
Colour screen CNaviDrive colour display
Display of tyres in good condition
T y r e v e r y d e fl a t e d
T y r e d e fl a t e d
“Puncture”
31- 65
The driver's and the front and rear passengers' seats have sensors that detect non-fastening/unfas-tening of the seat belts.
The fastened/non-fastened status of the seat belts for each type of seat is indicated by the illumination o r fl a s h i n g o f t h e w a r n i n g l a m p s 1, 2 and 3.
M O N I T O R I N G
Page 25 of 216
28
II
1
3
2
F R O N T S E A T S
ADJUSTMENT OF THE BACKREST ANGLE
Action the control 1 and adjust the angle of the backrest.
It is possible to tilt the backrest 45° forwards until it locks. To unlock it, press control 1.
ADJUSTMENTS TO THE HEIGHT AND ANGLE OF THE HEAD RESTRAINT
To raise it, pull upwards.
To lower it, press on the control 2 to unlock it, and simultaneously on the head restraint itself.
To adjust the angle of the head restraint, tilt it forwards or rearwards at the bottom.
To raise it, press control 2 to unlock it, then pull it upwards.
CONTROLS FOR THE HEATED SEATS
The front seats can be heated independently of each other . On the con-trols for the heated seats 3 located on the outer side of the seats, rotate the knob to select any of three heat intensities:
0: Off.
1: Slight heat.
2: Medium heat.
3: Maximum heat.
Note: The heated seats only operate when the engine is running.
SEAT HEIGHT AND SLIDE ADJUSTMENTS
See following page.
Page 28 of 216
31
II
23
1
S E A T B E L T S W A R N I N G L A M P
OPERATION
The driver's and the front and rear passengers' seats have sensors that detect non-fastening/unfas-tening of the seat belts.
The fastened/non-fastened status of the seat belts for each type of seat is indicated by the illumination o r fl a s h i n g o f t h e w a r n i n g l a m p s 1, 2 and 3.
FUNCTIONING OF THE SYSTEM OF DETECTION
Driver's and front passenger's seats
When you switch on the ignition:If the driver's seat belt is not fastened, the warning lamp If1 illuminates in the instrument panel.If the passenger's seat belt is not fastened, the warning lamp If3 lights up.
A b o v e 2 0 k m / h ( 1 2 m p h ) , t h e w a r n i n g l a m p fl a s h e s f o r n o n - f a s t e n i n g / u n f a s -tening, accompanied by a message and a sound signal for around 2 min- u t e s . T h e n t h e w a r n i n g l a m p ( s ) 1 and/or 3 remain on.
Rear passengers' seats
When you switch on the ignition, warning lamp 2 lights up to make the driver and any passengers aware.
Once the doors are closed and the engine started, a message tells you the fastening status of the rear belts for 30 seconds.
After this time, if one or more of the rear belts are not fastened:Warning lamp 2 comes on, if your speed is less than around 2 0 k m / h ( 1 2 m p h ).Warning lamp 2 fl a s h e s , a c c o m p a n i e d b y a m e s s a g e a n d a s o u n d s i g n a l for about two minutes, if your speed is above around 2 0 k m / h ( 1 2 m p h ).Note:The detection of non-fastening of rear seat belts is deactivated when you switch off the ignition or if one of the vehicle's doors is opened.
A child seat installed on the front passenger's seat may not be detected.
Page 81 of 216
83
IIIA
A C C E S S
To make it easier to open the doors, the windows automatically open by a few millimetres.Note: This movement occurs immediately you touch an interior door handle.
The window recloses, automati-cally adjusting for a perfect seal.
IMPORTANT
This function has no anti-pinch. Do not leave your hand on the window when you close the door
Any interruption of your vehicle's electrical supply will prevent the windows from opening and closing correctly.
Remark: Travelling at high speed, closing of windows may be hin-dered by the aerodynamic pres-sure. Acoustic comfort may then be adversely affected.
ELECTRICALLY-CONTROLLED CHILD SAFETY
This deactivates the controls in the rear of the vehicle, both for the rear win-dows and for opening the rear doors from the inside.
For Pack Lounge seats, the seat slide adjustments, and those fo r the front seats from the rear of the vehicle, are also deactivated.
Activation
The electric safety device is activated by pressing the control A located on t h e w i n d o w s c o n t r o l p a n e l . A m e s s a g e a p p e a r s t o c o n fi r m t h a t t h e c h i l d safety is activated.
It is still possible to open the doors from the outside and to operate the elec-tric windows from the front of the vehicle.
Before changing or repairing the battery, open all four windows.
If you unlock your vehicle using the key because of a problem with the battery, be aware that opening/closing a door wi th the window closed can seriously damage the glass, even to the point of breaking it.
Page 84 of 216
86
III
A U T O M A T I C A I R C O N D I T I O N I N G
AIR CONDITIONING
This system automatically adjusts the temperature, the fl o w o f a i r a n d t h e d i s t r i b u t i o n o f a i r i n s i d e t h e c a b i n , depending on your desired comfort level.
Provided you retain automatic mode (by pressing button “AUTO ” ) a n d a l l t h e a i r v e n t s a r e o p e n , y o u w i l l m a i n -tain an optimum comfort level, also removing humidity and misting, whatever the ambient climatic conditions.
The temperature inside the cabin cannot be lower than the temperature outside if the air conditioning is not operating.
To be effective, the air conditioning should only be used with the windows closed. If after a lengthy stop in bright sunlight the interior temperature is excessive, air the passenger compartment by opening the windows for a few moments, then close them again.
To keep the air conditioning compressor well sealed, it is essential to operate the air conditioning at least once in every month.
The air conditioning operates by using power from the engine. This results in a slight increase in fuel con-sumption.
Sensors
The automatic regulation of the air conditioning inside the cabin uses a number of sensors (sunlight, ambient t e m p e r a t u r e , i n s i d e t e m p e r a t u r e , e t c . ) r e l i e v i n g y o u o f the need to make your own adjustments within a normal temperature range.
The humidity sensor is there to prevent misting inside the vehicle.
Be careful not to obstruct the sensors A and C.
Air inlet
Check that the exterior grille for the air inlet, at the bot-tom of the windscreen, is clean and free of dead leaves, snow, etc.
If washing the vehicle with a high pressure jet, avoid targeting the air inlet zone.
Air circulation
For your comfort we advise you to maintain a proper distribution of air within the cabin, both at the front and at the rear.
The air vents to the face have thumbwheels so that you c a n a d j u s t t h e fl o w o f a i r , a n d g r i l l e s t o o r i e n t t h e d i r e c -tion.
T h e r e a r e a i r v e n t s o n t h e fl o o r u n d e r n e a t h t h e f r o n t seats and on the rear control panel, for enhanced heat-ing of the rear seat positions.
Do not obstruct the air outlets located in the boot area.
D u s t / p o l l e n fi l t e r
T h e r e i s a fi l t e r f o r e x c l u d i n g p o l l e n a n d d u s t .
T h i s fi l t e r h a s t o b e c h a n g e d a c c o r d i n g t o t h e v e h i c l e maintenance schedule. See “Maintenance Guide”.
Additional heating
Vehicles with an HDi engine may be provided with auto-matic additional heating for enhanced comfort.
It is normal to notice slight odours or smoke emissions, especially when the vehicle is idling or stationary.
Page 93 of 216
95
III
A
BC
D
R E A R S E A T S
Seat cushion folded.
Stow the head restraints.
Press the control A located at the end of the backrest and fully tilt for-wards.
The benchseat backrest can be folded in two sections. When you reposition the backrest, make sure that it locks in place.
Your vehicle's boot can be kept isolated from the passenger com-partment.
To lock the access to the boot:1. Place the benchseat in its cor-rect position.The red warning lamp on con-trol A should no longer be vis-ible.
2. Insert the ignition key in the lock.3. Lock it.
Before moving the seats
So as to avoid damaging the seat belts by jamming them, take care to keep them to the sides of the backrest.
LOCKING/UNLOCKING OF THE ACCESS INTO THE BOOT VIA THE REAR BENCHSEATREAR CENTRAL SEAT BELT
For easier opening of the seat belt cover D , y o u s h o u l d fi r s t r a i s e t h e central head restraint.
I n s e r t t h e fi r s t f a s t e n i n g C into the f r o n t l e f t h a n d ( b l a c k ) b u c k l e , t h e n insert the second fastening B into the front right hand buckle.
Page 94 of 216
96
III
B
A
P A C K L O U N G E S E A T S
ANGLE OF THE REAR LAT-ERAL HEAD RESTRAINTS
To alter the angle of the rear lateral head restraints, lift them then tilt them upwards.
LONGITUDINAL ADJUST-MENT OF THE FRONT PAS-SENGER'S SEAT
For more room for the rear passen-ger, it is possible for the front pas-senger's seat to be slid forwardfrom the rear seat position.
To slide the front passenger's seat forward, press on the control B at the centre of the armrest.
Remark: This control B is not active if adjustments are being made simultaneusly at the front.
The front passenger's seat will slide forward for as long as you keep control B pressed. It stops immedi-ately you release control B.
Remark: Use of the child safety deactivates button B. See “Win-dows”.
ADJUSTING THE SEAT AND ITS BACKREST
You can adjust the longitudinal position of the seat and the angleof its backrest simultaneously using the control A.
IMPORTANT
Pack Lounge seats cannot be folded.
Remark: Use of the child safety deactivates button A. See “Win-dows”.
Page 96 of 216
98
III
C H I L D R E S T R A I N T S
CHILD SEATS SECURED BY MEANS OF THE VEHICLE SEAT BELT
In conformity with Directive 2000/3, the table tells you to what extent each of the seat positions in your vehicle may take a child seat that is secured by means of the vehicle seat belt and approved as “Univer-sal” as a function of the weight of the child.
Consult “User Precautions”, chapter on “Child Safety” at the end of this handbook, in order to ensure that you are installing your child in conditions of maxi-mum safety.
Seat position(s)
Weight of child
Up to 10 kg and up to 13 kg (groups 0 a n d 0 + )
9 - 18 kg ( g r o u p 1 )15 - 25 kg ( g r o u p 2 )22 - 36 kg ( g r o u p 3 )
Front passenger’s ( a ) U ( R ) U ( R ) U ( R ) U ( R )
Lateral rearUUUU
Central rearL1, L2XL4L4
U: Seat position suitable for the installation of a universal rear-facing child seat and a universal forward-facing child seat position.
U ( R ) : S e a t p o s i t i o n s u i t a b l e f o r i n s t a l l a t i o n o f a u n i v e r s a l r e a r - f a c i n g c h i l d seat and of a forward-facing seat. The vehicle seat should be adjusted to the highest position.
( a ) : I n t h e f r o n t p a s s e n g e r ' s s e a t p o s i t i o n , i t i s i m p e r a t i v e t o d e a c t i v a t e t h e front passenger's airbag if you are installing a “rear-facing chil d seat” there. Otherwise the child risks being killed or seriously injured should the airbag deploy.
Before placing your child in the front passenger’s seat position, consult the legislation currently in force in your country on the carrying of ch ildren in this position.
L-: Only the child seats indicated may be installed in the seat position con- c e r n e d ( d e p e n d i n g o n c o u n t r y ) . S e e “ C h i l d s e a t s ” .
X: Position not suitable for installation of a child seat of the weight group indicated.
In the front passenger's seat position, it is imperative to deactivate the front passenger's airbag if you are installing a “rear-facing child seat” there. Otherw ise the child risks being killed or seriously injured should the airbag deploy.
T a k e c a r e t o c o m p l y w i t h t h e fi t t i n g i n s t r u c t i o n s g i v e n i n t h e c h i l d s e a t m a n u f a c t u r e r ’ s i n s t a l l a t i o n guide.
Page 97 of 216
99
III
ab
ab
c
C H I L D R E S T R A I N T S
Pack Lounge seats
ISOFIX ANCHORING POINTS AND THE ISOFIX FASTEN-ING SYSTEM
Your vehicle is type-approved according to new ISOFIX direc-tives. The lateral rear seats of your vehicle are each equipped with regulation ISOFIX anchoring points.
Incorrect installation of a child seat in a vehicle compromises protec-tion of the child in the event of a col-lision. The ISOFIX system enables you to minimise the risks posed by i n c o r r e c t fi t t i n g . T h e I S O F I X f a s -tening system gives you a conven- i e n t , s t r o n g a n d r e l i a b l e fi t t i n g f o r a child seat in your vehicle.
Benchseat
The ISOFIX fastening sys-tem
The ISOFIX system features 3ringsfor each lateral rear seat position:Two bottom rings a and blocated between the backrest and the seat cushion. These are about 28 cm apart, con-cealed in the case of a bench- s e a t u n d e r a fl a p w i t h t h e l o g o ISOFIX.
One top ring c fi x e d o n t h e r e a r shelf, concealed u n d e r a fl a p with the logo TOP TETHERbehind the head restraint.