torque Citroen CX 1983 1.G Owner's Guide

Downloaded from www.Manualslib.com manuals search engine - Calibration of thermal switch for temperature warning lamp .__._... 135 ? 3” C
- Type of oil . . .._..__.._._..___._._._._._.................,,.........._..._..._................. TOTAL (( FLUIDE 1) T
- Total capacity f
iur//rdiir/g ~~arhos ) .._._.._.......................... 5.5 litres ( 9.7,pts )
- Interchanqeable suction filter
- Filling the converter during fitting. actuate the electro-valve a dozen times.
Tightening torques :
- Electra-valve fixing screw ............................................................ 2.8 daNm ( 20 l/2 ft.Ib )
- Union-screw for oil pipe ............................................................... 3 to 3.5 daNm ( 21 l/ 2 to 25 l/ 2 ft.Ib )
- Suction filter .................................................... ........... ............. 3.5 to 4 daNm ( 25 l/2 to 29 ft.Ib )
- Contact fixing screws ................................................................... 0.2 to 0.3 daNm ( 1 11 2 to 2 ft.lb )
IMPORTANT : In the course of repairs, it is permissible to replace a 697-type ( .CX 2200 ) converter by a 693-type
( CX 2400 ) one.
However, the reverse operation ( replacing a 693-type by a 697-type converter ) is prohibited.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 320-00 : (.l~n~~/(-/(,~iz/i(-c m/d s/we-in: ~o~///,w. o/ //I<, /r,t~///c cc,,,, or/r r Op. MA. 32Oz.00 3
III. OPERATIONAL DIAGRAM OF TORQUE CONVERTER
Engine running, gear-lever in neutral

Downloaded from www.Manualslib.com manuals search engine MANUAL 4-SPEED GEARBOX
Tightening torques
97 l/2 to 108 112
ti 1,/2 ft.lbl
Drain and filler plug .._.. 3 5 to 4 5 daNm ( 25 1 2 to 32 l/ 2 ft Ib)
Final drive casing assembly nuts ’ dia 8 mm )
2 8 daNm ( 20 : 2 it Ib )
Final drive casing assembly nuts < dia 1Zmrilj .. ......” 5 duNm 36 it lb 1
Bush-nut for gear selector shaft .. ... 1 I to 12 daNrn ( 79 112 to 87 ft Ib )
Bush-nut for dipstick guide .... .... ... ” .. .. ... 3 to 4 daNm ( 21 1 2 to 29 ft Ib i Assembling the gearbox casings :
Sealing Smear the contact faces of the gearbox casings and the rear cover with sealing compound

Downloaded from www.Manualslib.com manuals search engine TORQUECONVERTERGEARBOX
I. CHARACTERISTICS
Gearbox ratios :
NOTE Speeds are-given for vehicles with 185 HR 14 XVS tyres the roiling circumference under load of which
is 1.970 m.
The gearbox with a safety locking device ( P
position ) for parking
Gearbox ratios
Speedometer drive ratio 5 X 12 Lkbrication :
Type of oil TOTAL (( FLUIDE T )) ,......._._ ,..,.,_......._..,.............._..,_....,.,...._.. .._..._._._...........
Total capcity ( including converter ) .._ ,..,.
5.5 litres ( 9.7 pts ) approx.
Draining . . .._.__........_..................................................................................... 2 to 3 litres ( 3.5 to 5.3 pts ) ( depending
on draining time
Difference between min. and max on dipstick .._..... ..:. 0.15 litres ( 0.26 pts )
VERY IMPORTANT It is ABSOLUTELY ESSENTIAL to use TOTAL (( FLUIDE T ))
Gear control :
Floor mounted gear lever
Gear pattern

Downloaded from www.Manualslib.com manuals search engine TORQUE CONVERTER GEARBOX
Tightening torques
1 2.b da Nm 1
19.5 to 21.5 da Nm
141 to 155 l/2 ft.lb)
I
- Gearbox casing assembly screws and nuts ( dia 8 mm 1 ? 3 daNm ( 20 1 / 2 ft.Ib )
Final drive casing assembly nuts ( dia ~- 10 mm i
5 daNm ( 36 ft.Ib )
Bush nut for selector shaft
.._.. _..._.. 11 to 13 daNm ( 7” 1 2 to 94ft.Ib)
Suction filter 3 5 to 4 daNm ( 25 l/ 2 to 29 ft.Ib )
.._..,.
- Drain and filler plugs
3 5 to 4 5daNmJ 25 1,‘2to32 1; 2ft.Ib)
- Screw for return union to valve unit
.,... 3 to 3.5 daNm (21 1/2to25 l/2 ft.lb)

Downloaded from www.Manualslib.com manuals search engine TORQUE CONVERTER GEARBOX
( gear sequence )
REVERSE GEAR
1st GEAR 2ud GEAR
3rd GEAR

Downloaded from www.Manualslib.com manuals search engine 12 OPERATION NP MA. 330.00 : (haro? gvmhr,, III. DRAINING AND REFILLING THE GEARBOX AND THE CONVERTER
1. Place the vehicle over a pit 01 on a ramp
2. Draining :
Remove the following
spare wheel
drain plugs ( I), ( 2 I and i 3 ),
plug ( 5) from the filler orifice
NOTE The suction filter ( 4) for the converter
pump must be replaced at the 1000 km ( 60C miles j
service.
3. Filling :
Refit drain plugs ( 1). (2 1 and ( 3 1.
Tightening torque : 3.5 to 4.5 daNm ( 25 l/2 to
32 l/2 ft.lb )
VERY IMPORTANT :
USE EXCLUSIVELY
(< TOTAL FLUIDE T o
THEUSEOFANYOTHERLUBRICANTWOULD
DESTROY THE CLUTCH, AND CONSEQUENTLY
THE CONVERTER
Fill up the gearbox
( Co$acity 2-3 litres ( 3 l/2 to 5 l/4 pints )
according to draining time)
Check the level with the dipstick
4. Top up the gearbox :
> nc I<, b<’ r<,r/niii 10 <,hini,,
I/><, o) Immobilise the front wheels and put the hond-
broke on.
b) Run the engine at idlinq speed, and engage 01
gear ( 3rd gear, for example )
Slightly move the gear lever to actuate the
electro .valve controlling the clutch, ( it is
actuated when a click is heard ). ( Repeat a
dozen times ).
c) Check the level with the dipstick with the
enqine running and gear lever in the P position.
d) Fit the filler plug.
5. Fit spore wheel

Downloaded from www.Manualslib.com manuals search engine FIVE-SPEED MANUAL GEARBOX
Tightening torques
(130 to 145 ft.lb)
II I lr II III
\/
2.8 da Nm
(20 l/2 ft.lb)
Filler plug and main plug 3.5 to 4 5 daNm ( 25 l/2 to 32 I/ 2 ft Ib )
Final drive casing assembly nuts ( dia -z 8 mm )
.,..._.,. 2.8 daNm ( 21) 11.2 ft.Ib )
Fianl drive casing assembly nuts ( dia l@ mm )
5 daNm ( 36 ft fb )
Selector shaft bush-nut _...... . . . . . .._...._...._...._..__................
11 to 12 daNm ( 79 l/2 to 87 ft.Ib )
Assembling the gearbox casings :
Sealing Smear the contact i?ces of the casings and the cover with sealing compound

Downloaded from www.Manualslib.com manuals search engine HIGH PRESSURE SINGLE CYLINDER PUMP f-/i, to-0 j
1.7 to 1.9 daNm
12 1/‘2 to 14
ft.lb
1. Plug
2. O-ring
3. Seat
4. O-ring
!i. O-ring
6. Sleeve and piston
7. Snap ring
8. Spring plate
9. Spring
10. Body and intermediate piston
11. Plunger
12. Roller
12
ZESCRIPTiOH
Reciprocating single-cylinder pump, operated by an eccentric machined on camshaft
Operating ratio ,.
_..__.,.,..._.. . . . . . . . . . . . . :... ,. 1 cycle/ 2 engine revolutions
-
- Piston diameter .._....._.....,,.......,............. .,.,.,.,... .,. 14 mm
- Piston stroke ( (‘c-c c,///rrc~ /if/ ) ,. ,,... ‘10 t 0.10 mm
.._..... ..,....,.,............. ..I.
- HI ,,‘OJJ f~ji,~c/icntin~f : output (111fr1cr /on{1 of I75 1~nr.s.
/ictirl f/f (10” (. i.. 1.07 cm3per cycle
SPECIAL FEATURES
Tightening torques :
- Pump fixing screw on crankcase .._.....,.._._..,.....,.............. .._,__. _. _.. .._......_........ 19 mN ( 1.9 m.kg) ( 14ft.b)
( Fit a ,~c,~I’ paper sc~nl ~r,hcvc,r’c~~ pzrmp is dismar~tld~ -

Downloaded from www.Manualslib.com manuals search engine H.P. SINGLE-CYLINDER PUMP ( 10/‘1’)7(, -I
1.7 to 1.9daNm
12 l/2 to 14
ft.lb
1. Plua
2.0-= -ring
3. Seat
4. O-ring
5. O-ring
6. Sleeve and piston
7. Snop ring
8. Spring cup
9. Spring
10. Body and intermediate pist
11. Plunger
12. Roller breather
13. Pump unions
HP output
1
2
------3
One-way
e-
iI 7
.uH-.!.a
e
10
tn 11
ion
CHARACTERISTICS
It differs from the single-cylinder pump fitted up to lO/ 1976 only in the two pump breather unions.
Reciprocating single-cylinder pump, driven by an eccentric machined on the camshaft
- Operating ratio .._._._....._........ 1 cycle/ 2 engine revolutions
- Piston.diameter .._...................
14 mm
- Piston stroke I
ecrcwtric lijt J _......__._........_.._...,_........,._.._._...___,, 10 2 0.10 mm
- For iu fomalior~ : output ( unJer prc’ssure oil75 bars (2F3X psi),
and with fluid at 60’ C _.__.._______.._.___._.___,........_._....__.__.._............ 1.07
cm3 per cycle
SPECIAL FEATURES
Adiustments :
- Clearance between pump and body ( b+rc, tightwivg ) 0.05 to O-09 mm
- Clearartce obtained by usivg shims ojrli/!vrcrtt thirhc~sses 0.05 - 0.10 - 0.15 - 0.20 mm -,..
Tightening torques :
- Pump fixing screws on crankcase . . . . . . . . . ..__._.._.._...._...__.........._.,. 1.9 dab ( 14 ft.& )
( Fit a neu’ paper seal u’bencucr p~unp is dismant/cd)