Fuse ta
ble
Fuse N°
Rating
Functions
F
1
20 A
Engine control unit supply, cooling
fan unit control relay,
multifunction engine control main relay, injection pump
(Diesel).
F2
15 A
Horn.
F
3
10 A Front
/rear wash-wi
pe.
F4
20 A
LED lamps.
F5
15 A
Diesel heater
(Diesel
), particle
filter additive pump
(Diesel
),
air
flow sensor
(Diesel
), blow-by heater and electrovalves
(VTi).
F
6
10 A
ABS/ESP control unit, secondar
y stop switch.
F7
10 A
Electric power steerin
g, automatic
gearbox.
F8
25 A
Starter control.
F
9
10 A
Switching and protection unit (Diesel).
F10
30 A
Fuel heater (Diesel), blow-by heater (Diesel), fuel pump
(VTi), injectors and ignition coils (petrol).
F11
40 A H
eater blower.
195
Practical information
Fuse
N°
Rating
Functio
ns
F12
30 A
Windscreen wipers slow/fast speed.
F13
40 A
Built-in s
ystems inter
face suppl
y (ignition positive
).
F14
30
A
Valvetronic suppl
y (VTi
).
F
15
10 A
Right-hand main beam headlamps.
F16
10 A
Left-hand main beam headlam
ps.
F17
15 A
Left-hand di
pped beam headlam
ps.
F1
8
15 A
Righ
t-hand dippe
d beam
headlamps.
F19
15 A
Oxygen sensors and electrovalves (VTi), electrovalves (Diesel), EGR electrovalve (Diesel).
F20
10 A
Pumps, electronic thermostat (VTi), timimg electrovalve (THP), water in fuel sensor (Diesel).
F21
5 A
Fan assembl
y control suppl
y, AB
S/ESP, turbo pump
(THP
).
Tab
le of m
axi-f
uses
Fuse
N°
Rating
Functio
ns
MF1*
60 A
Fan assem
bly.
MF2*
30 A
ABS/ESP pum
p.
MF3 *
30 A
ABS/ESP electrovalves.
MF4 *
60 A
Built-in Systems Interface (BSI) supply.
MF
5 *
60 A
Built-in
Systems Inter
face
(BSI) supply.
MF6 *
20 A
Additional coolin
g fan unit
(THP
).
MF7
*
-
Dashboard fusebox.
MF8 *
-
Not used.
* The maxi-fuses provide additional protection for the electrical s
ystems. All work on the maxi-fuses must be carried out b
y a CITROËN dealer.
Practical information
Battery
Procedure for charging your battery when it is flat or for starting the engine using another battery.
The battery is located under the bonnet.
To gain access to it: )
open the bonnet using the interior release lever, then the exterior sa
fety catch,
)
secure the bonnet stay,
)
remove the plastic cover by pulling on itsgrip for access to the two terminals,
)
unclip the
fusebox to remove the battery, i
f
necessary.
Access to the battery
)
Connect the red cable to the
positive
terminal (+) of the flat battery A
, then to the
positive terminal (+) of the slave battery
B.
Starting using another batter
y
) Connect one end o
f the green or black
cable to the negative terminal (-) of the
slave battery
B .
) Connect the other end of the green or black cable to the ne
gative terminal
(-) of the flat
batter
y A.
) Start the slave vehicle.
) Operate the starter of the broken down vehicle and let the engine run.
) Wait until the engine returns to idle and disco
nnect th
e cab
les.
