Citroen DS3 2015 1.G Owner's Manual

199
DS3_en_Chap08_info-pratiques_ed01-2015
F Start  the   compressor   by   placing   the   switch  a
t the " I"
  position   and   adjust   the   pressure  
t

o   the   value   shown   on   the   vehicle's   tyre  
p

ressure   label.
 T

o   deflate:   press   the   black   button   on   the  
c

ompressor   pipe,   at   the   valve   connector.
F

O
nce the correct pressure is reached, put
the switch to the " O"
  position.
F
 
R
emove   the   kit   then   stow   it.
Tyre under-inflation
detection
After repair of the tyre, the warning lamp   will   remain   on   until   the   system   is  
r

einitialised.
For
  more   information,   refer   to   the  
"

Under-inflation
 d
etection"
 s
ection.
Should
  the   pressure   of   one   or   more  
t

yres   be   adjusted,   it   is   necessary   to  
r

einitialise the under-inflation detection
system.
Refer to the "Under-inflation detection"
section.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Changing a wheelProcedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
T he tools are installed in the boot under the
f l o o r.
To
  gain   access   to   them:
F

o
pen the boot,
F
 
l
ift   the   boot   carpet   by   pulling   the   strap  
up

wards,
F
 
r
emove   the   polystyrene   storage   box,
F
 
u
nclip   and   remove   the   box   containing   the  
to

ols.
Access to the tools
List of tools Wheel with trim
When removing the wheel
, first
detach   the   trim   using   the   wheelbrace   1
pulling
  at   the   valve   passage   hole.
When refitting the wheel , refit the
trim
  starting   by   placing   its   cut-out   at   the  
v

alve   and   press   around   its   edge   with  
t

he   palm   of   your   hand.
1.
 W

heelbrace.
 F

or
 
removing
 
the
 
wheel
 
trim
 
and
 
removing
 
t

he
 
wheel
 
fixing
 
bolts.
2.
 J

ack
 
with
 
integral
 
handle.
 F

or
 
raising
 
the
 
vehicle.
3.
 "

Bolt
 
cover"
 
tool.
 F

or
 
removing
 
the
 
bolt
 
protectors
 
(covers)
 
o

n
 
alloy
 
wheels.
4.
 S

ocket
 
for
 
the
 
security
 
wheel
 
bolts
 
(located
 
i

n
 
the
 
glove
 
box).
 F

or
 
adapting
 
the
 
wheelbrace
 
to
 
the
 
special
 
s

ecurity
 
wheel
 
bolts
 
(if
 
your
 
vehicle
 
is
 
fitted
 
w

ith
 
them) All of these tools are specific to your
vehicle.
  Do   not   use   them   for   other  
p

urposes.
Never
  use   a   jack   other   than   the  
o

ne listed for the vehicle by the
manufacturer.
  If   the   vehicle   does   not  
h

ave one, contact a CITROËN dealer
or
  a   qualified   workshop   to   obtain   a   jack  
s

pecified   by   the   manufacturer.

201
DS3_en_Chap08_info-pratiques_ed01-2015
The spare wheel is installed in the boot under
the  floor.
According
  to   country,   you   will   have   either   a  
"

space   saver"   spare   wheel   or   a   temporary  
p

uncture   repair   kit.
For access to it, refer to the "Access to the
tools"
 s

ection.
Access to the spare wheel
Fitting the "space-saver"
type spare wheel
If your vehicle is fitted with alloy
wheels,   it   is   normal   to   notice,   when  
t

ightening   the   bolts   on   fitting,   that   the  
w

ashers   do   not   come   into   contact   with  
t

he   "space-saver"   type   spare   wheel.  
T

he wheel is secured by the conical
contact
  sur face   of   each   bolt.
Taking out the wheel
F Unscrew  the   yellow   central   bolt.
F  R aise   the   spare   wheel   towards   you   from  
t

he   rear.
F
 
T
ake   the   wheel   out   of   the   boot.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Putting the wheel back in place
F Put  the   box   back   in   place   in   the   centre   of  t
he   wheel   and   clip   it.
F
 
P
ut   the   polystyrene   storage   box   back   in  
p

lace.
F
 
R
efit   the   boot   floor   carpet   by   lightly   folding  
i

t   in   the   middle   (refer   to   the   "Boot   fittings"  
s

ection).
F
 P
ut
 
the
 
wheel
 
back
 
in
 
its
 
housing.
F
U
nscrew the yellow central bolt by a few
turns then place it in the centre of the
wheel.
F
 
T

ighten
 
fully
 
until
 
the
 
central
 
bolt
 
clicks
 
to
 
r

etain
 
the
 
wheel
 
correctly. On
  vehicles   equipped   with   a   "space-
saver" type spare wheel, the punctured
wheel can be stowed in place of the
"space-saver"
  wheel;   however   the   boot  
f

loor   will   not   then   be   flat.

203
DS3_en_Chap08_info-pratiques_ed01-2015
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not   block   traffic:   the   ground   must   be  
l

evel,   stable   and   not   slippery.
Apply
  the   parking   brake,   switch   off   the  
i

gnition   and   engage   first   gear*   to   lock  
t

he   wheels.
If
  necessary,   place   a   chock   under   the  
w

heel   diagonally   opposite   the   wheel   to  
be c

hanged.
It
  is   imperative   that   you   ensure   that   the  
o

ccupants   get   out   of   the   vehicle   and  
w

ait   where   they   are   safe.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   chromed   bolt   cover   from   each  o
f   the   bolts   using   the   tool   3   (alloy   wheels  
o

nly).
F
 
F
it   the   socket   4 on the wheelbrace 1 to
slacken
  the   security   bolt   (if   your   vehicle   is  
f

itted   with   them).
F
 
S
lacken   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
*


position R
 
for
 
an
 
electronic
 
gearbox,
 
P for an
automatic
 
gearbox.
Ensure
 
that
 
the
 
jack
 
is
 
stable.
 
If
 
the
 g
round
 
is
 
slippery
 
or
 
loose,
 
the
 
jack
 
c

ould
 
slip
 
or
 
drop
 
-
 
Risk
 
of
 
injury!
Take
 
care
 
to
 
position
 
the
 
jack
 
only
 
at
 
o

ne
 
of
 
the
 
jacking
 
points
 
A or B

under
the
 
vehicle,
 
ensuring
 
that
 
the
 
vehicle's
 
c

ontact area is well centred on the
head
 
of
 
the
 
jack.
 
Other wise,
 
there
 
is
 
a
 
r

isk
 
of
 
damage
 
to
 
the
 
vehicle
 
and/or
 
the
 
j

ack
 
might
 
drop
 
-
 
Risk
 
of
 
injury!
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
F Position  the   foot   of   the   jack   2   on   the   ground  a
nd ensure that it is directly below the
front
A or rear B   jacking   point   provided   on  
t

he underbody, whichever is closest to the
wheel
  to   be   changed.
O

n vehicles fitted with sill finishers, the
jacking
  location   is   indicated   by   a   marking  
o

n   the   finisher.   The   jack   must   be   placed  
c

entrally   in   line   with   this   marking,   at   the  
j

acking   point   located   behind   the   finisher  
a

nd   not   on   the   plastic   finisher   itself. F
 R emove   the   bolts   and   store   them   in   a   clean  p
lace.
F
 
R
emove   the   wheel.
F
 E xtend   the   jack   2   until   its   head   comes   into  c
ontact   with   the   jacking   point   A or B   used.  
T

he contact area A or B on the vehicle
must
  be   engaged   with   the   central   part   of  
t

he   head   of   the   jack.
F

Ra
ise the vehicle until there is sufficient
space
  between   the   wheel   and   the   ground  
s

o   that   the   spare   (not   punctured)   wheel   can  
t

hen   be   fitted   without   difficulty.

205
DS3_en_Chap08_info-pratiques_ed01-2015
Fitting a wheel
After changing a wheel
To store the punctured wheel in the
boot  correctly,   first   remove   the   central  
c

ove r.
When
  using   the   "space-saver"   type  
t

emporary-use   spare   wheel,   do   not  
e

xceed   50   mph   (80   km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop   without   delay.
Have the punctured wheel repaired and
replace it on the vehicle as soon as
possible.
Do
  not   drive   with   more   than   one  
t

emporary-use   spare   wheel   fitted   to   the  
v

ehicle   at   one   time.
List of operations
F Put  the   wheel   in   place   on   the   hub.
F  S crew   in   the   bolts   by   hand.
F
 
P
re-tighten   the   security   bolt   (if   your   vehicle  
i

s   fitted   with   them)   using   the   wheelbrace   1
fitted
  with   the   socket   4.
F
 
P
re-tighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
F Lower  the   vehicle   fully.
F  F old   the   jack   2   and   detach   it.F
 T ighten   the   security   bolt   (if   your   vehicle   is  f
itted   with   them)   using   the   wheelbrace   1
fitted
  with   the   socket   4.
F
 
T
ighten   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
F
 
R
efit   the   chromed   bolt   covers   on   each   of  
t

he   bolts   (with   alloy   wheels   only).
F
 
S
tore   the   tools   in   the   box.
RACING tyres
driving in winter conditions
The 215/40 R18 89W tyres fitted as standard are   not   suitable   for   severe   winter   conditions.  
W

e   recommend   that   you   use   suitable   winter  
t

yres   during   periods   of   very   cold   weather.
If you want to fit snow chains or
snow
  socks   to   your   vehicle,   contact  
a C

ITROËN dealer for advice on the
tyres
  recommended   for   your   vehicle.

207
DS3_en_Chap08_info-pratiques_ed01-2015
It is strongly recommended that before you   leave,   you   practise   fitting   the   snow  
c

hains   on   a   level   and   dry   sur face.
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking.
T he   snow   chains   must   be   fitted   only  
t

o   the   front   wheels.   They   must   never  
b

e fitted to "space-saver" type spare
wheels.
Take
  account   of   the   legislation   in   force  
i

n your country on the use of snow
chains
  and   the   maximum   running  
s

peed
 a
uthorised.
Avoid
  driving   with   snow   chains   on  
r

oads that have been cleared of snow,
to
  avoid   damaging   your   vehicle's   tyres  
a

nd   the   road   sur face.   If   your   vehicle  
i

s   fitted   with   alloy   wheels,   check   that  
n

o   part   of   the   chain   or   its   fixings   is   in  
c

ontact   with   the   wheel   rim.
Advice on installation
F If  you   have   to   fit   the   chains   during   a   journey,   stop   the   vehicle   on   a   flat   sur face   on   the   side   of   the  r
oad.
F
 
A
pply   the   parking   brake   and   position   any   wheel   chocks   to   prevent   movement   of   your   vehicle.
F
 
F
it   the   chains   following   the   instructions   provided   by   the   manufacturer.
F
 
M
ove   off   gently   and   drive   for   a   few   moments,   without   exceeding   30   mph   (50   km/h).
F
 
S
top   your   vehicle   and   check   that   the   snow   chains   are   correctly   tightened.
Use
  only   the   chains   designed   to   be   fitted   to   the   type   of   wheel   fitted   to   your   vehicle:
Vehicle Original
  tyre   sizeMaximum
  link   size.
DS 3 185/65
  R159
  mm
195/55
  R16
205/45
  R17cannot be fitted with chains
DS
  3   R ACING 215/40
  R18cannot be fitted with chains
For
  more   information   on   snow   chains,   contact   a   CITROËN   dealer   or   a   qualified   workshop.
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
Changing a bulb
The headlamps are fitted with polycarbonate   glass   with   a   protective  
c

oating:
F

d
o not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
F
 
u
se   a   sponge   and   soapy   water   or   a  
p

H neutral product,
F
 
w
hen   using   a   high   pressure  
w

asher   on   persistent   marks,   do   not  
k

eep   the   lance   directed   towards  
t

he   lamps   or   their   edges   for   too  
l

ong,   so   as   not   to   damage   their  
p

rotective   coating   and   seals.
Halogen headlamps
1. Direction  indicators   (PY21W   amber).
2. S idelamps ( W5W).
3.
 M

ain   beam   headlamps   (H1-55W).
4.
 D

ipped   beam   headlamps   (H7-55W).
5.
 F

ront   foglamps   (PSX24W).
6.
 L

ED   lamps   (LEDs).
Changing
 
a
 
bulb
 
should
 
only
 
be
 
done
 
a

fter
 
the
 
headlamp
 
has
 
been
 
switched
 
o

ff
 
for
 
several
 
minutes
 
(risk
 
of
 
serious
 
b

urns).
F

D

o not touch the bulb directly with
your
 
fingers,
 
use
 
a
 
lint-free
 
cloth.
It
 
is
 
imperative
 
to
 
use
 
only
 
anti-
ultraviolet
 
(UV)
 
type
 
bulbs
 
to
 
avoid
 
d

amaging
 t

he
 h

eadlamp.
Always replace a failed bulb with a
new
 
bulb
 
with
 
the
 
same
 
type
 
and
 s
pecification.