instrument panel CITROEN DS3 CABRIO 2014 Handbook (in English)

Automatic rain sensitive
windscreen wipers
The windscreen wipers operate automatically,
without any action on the par t of the driver, if rain is detected (sensor behind the rear view mirror), adapting their speed to the intensity of
the rainfall.
Activation
This is controlled manually by the driver bypushing stalk Ato the "AU TO "position.
It is accompanied b
y the illumination
of this indicator lamp in the
instrument panel and a messa
ge in
the multifunction screen.


Switching off

This is controlled manually by the driver by moving stalk A
upwards, returning it to
position
"0" .
It is accompanied b
y the indicator lamp
in the instrument panel going off and a message in the multifunction screen.
The automatic wiping must be reactivated if the ignition has been off for more than one minute, by pushingstalk Adownwards.

123Visibility








Interior mood lighting The dimmed passenger compar tment lighting improves visibility in the vehicle when the lightis poor.


Switching on
At night, the illumination of footwells and thecentral dashboard storage compar tment comes
on automatically when the sidelamps areswitched on.
Switching off
The interior mood lighting switches off automatically when the sidelamps areswitched off.
It can be switched off manually using the instrument panel lighting rheostat button. ) With the lighting on, press several times on
the left hand button of the instrument panel
to progressively reduce the dashboard lighting level. ) Press again to reduce the lighting level
to the minimum and switch off the interior
mood lighting.

This comes on automatically when the boot is opened and goes off automatically when the boot is closed.




Boot lamp
The lighting time varies according to the circumstances:


- when the ignition is off, approximately ten minutes,

- in energy economy mode, approximatelythirty seconds,

- when the engine is running, no limit.

153Safety
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more
quickly, thus reducing the stopping distance.

Activation

It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
When braking in an emergency, press firmly without releasing the pressure.














Trajectory control systems
Anti-slip regulation (ASR)
and electronic stability
pro
gramme (ESP)
The anti-slip regulation (also known as TractionControl) optimises traction to prevent skiddingof the wheels, by acting on the brakes of the
driving wheels and on the engine.
The electronic stability programme acts on the
brake of one or more wheels and on the engine
to keep the vehicle on the trajectory required
by the driver, within the limits of the laws of physics.

Activation

These systems are activated automaticallyeach time the vehicle is started.
They come into operation in the event of a gripor trajectory problem.
This is indicated b
y flashing of this
warning lamp in the instrument panel.

Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on softground...), it may be advisable to deactivate the ASR and ESP systems, so that the wheels can
move freely and regain grip. )Press the "ESP OFF"button, located on
the left below the steering wheel.
Illumination of the lamp in the button indicates
that the ASR and ESP s
ystems are deactivated.


Reactivation

These systems are reactivated automatically each time the ignition is switched back on or from 30 mph (50 km/h) except 1.6 litre (THP 150, THP 155 and THP 160) and
RACING petrol engines. )
Press the "ESP OFF"
button again to
reactivate them manually.

Operating fault

The ESP/ASR systems offer exceptional safety in normal driving, butthis should not encourage the driver to take extra risks or drive at high speed.
The correct functioning of these systems depends on obser vation of themanufacturer's recommendations on:


- wheels (tyres and rims),

- braking components,

- electronic components,

- assembly and repair procedures.
After an impact, have these systems checked by a CITROËN dealer or a qualified workshop.
Illumination of this warnin
g lamp in the
instrument panel and the lamp in the
"ESP OFF"button, accompanied b
y
an audible signal and a message in
the multifunction screen, this indicates
a malfunction of these systems.
Have it checked b
y a CITROËN dealer or a qualified workshop.

Safety
Seat belts


Front seat belts


The front seat belts are fitted with apretensioning and force limiting system.
This system improves safety in the frontseats in the event of a front or side impact.
Dependin
g on the severity of the impact, thepretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the i
gnition is on.
The force limiter reduces the pressure of the
seat belt on the chest of the occupant, so
improving their protection.Fastening
) Pull the strap, then inser t the tongue in thebuckle. )
Check that the seat belt is fastened correctly by pulling the strap.

Unfastening
)
Press the red button on the buckle. )
Guide the seat belt as it is reeled in.


Seat belt not fastened / unfastened warning lamp
When the ignition is switched on,
this warning lamp comes on in the
instrument panel, if the driver and/or
the front passenger has not fastened their seat belt.
From approximately 12 mph (20 km/h)this warning lamp flashes for two minutes
accompanied by an audible signal of increasingvolume. Once these two minutes have elapsed,
this warning lamp remains on until the driver
and/or the front passenger fastens their seat belt.

Deactivation
Only the passenger's front airbag can be deactivated:)with the ignition off, inser t the key in thefpassenger airbag deactivation switch, )turn it to the "OFF"position,)then, remove the key keeping the switch in
the new position.
This warnin
g lamp comes on in the
instrument panel when the ignition is
on and until the airbag is re-activated.
To assure the safety of your child,the passenger's front airbag mustbe deactivated when you install a "rear facing" child seat on the front passenger seat. Other wise, the child would risk beingseriously injured or killed if the airbag were deployed.

Reactivation

When you remove a child seat that hasbeen fitted "rear wards facing", turn switch to
the "ON"position to re-activate the airbag and
so assure the safety of your front passenger in
the event of an impact.

Operating fault
If this warning lamp comes on in the instrument panel, you must contact
a CITROËN dealer or qualified
workshop to have the system checked. The
airbags may no longer be deployed in the event
o
f a serious impact.

Curtain airbags
System which protects the driver and passengers (with the exception of the rear centre passenger) in the event of a serious side
impact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compartment area.
Deployment
The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or par t of the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or rear occupant of the vehicle and the windows.


Operating fault

In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be deployed.
In the event of a rear or front collision, the airbag is not deployed. I
f this warning lamp comes on in theinstrument panel, accompanied by
an audible signal and a message in
the screen, contact a CITROËN dealer or a
qualified workshop to have the system checked.The airbags may no longer be deployed in theevent of a serious impact.

169Driving

Display in the instrument panel


Gear lever positions
N
. Neutral R
. Reverse 1 2 3 4 5 / 6.Gears in manual mode.
AUTO. This comes on when automated mode
is selected. It goes off when changing tomanual mode.
)Place your foot on the brakewhen this warning lamp flashes (e.g.: star ting the engine).


You must keep your foot on the brake pedal while star ting the engine.
Moving off
)
Select position N
. )
Press the brake pedal fully. )
Start the engine.
N
appears in the instrument panel.
Nflashes in the instrument panelscreen if the gear lever is not inposition N
when star ting.
)
Select automated mode (position A
), Amanual mode (position M ) or reverse(position R)R
AUTOand 1
, 1 or R
appear in the
instrument panel.
) Release the parking brake.)
Progressively take your foot off the brakepedal.

Depending on the type of electronicgearbox, the vehicle may move off onits own (refer to the paragraph "Creep function").

Do not press the brake and clutchpedals simultaneously. This can cause rapid clutch wear.
)
Accelerate away.

Creep function
(depending on equipment)
This function allows the vehicle to bemanoeuvred more easily at low speeds (whenparking, in traffic jams...).
With the gear lever in position A , Mor R, the
vehicle moves as soon as you take your foot off the brake pedal , at low speed and
with the engine at idle.

Automated mode
AUTOand the gear engaged appear
in the instrument panel.
The gearbox then operates in auto-adaptive
mode, without an
y action on the par t of the
driver. It continuously selects the most suitablegear taking account of:


- optimisation of fuel consumption,

- drivin
g style,

- road conditions,

- vehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the pointof resistance.
You can change mode at any time by moving the gear lever from A to M
or the other way round.

The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.

Do not leave children unsuper visedinside the vehicle when the engine is running.
)
Select position A.
Never select neutral (position N) whenmoving.


Te m p o r a ry control of gear
changing

You can temporarily take over control of gear changes using the steering mounted "+"and "-"
control paddles: if the engine speed
allows, the gear change is carried out.
This function allows you to anticipate certain situations such as over taking another vehicle or
approaching a bend.
After a few moments without any action on the paddles, the gearbox resumes control of gear changing automatically.

171Driving
The gear change requests are only carried out
if the en
gine speed permits.
It is not necessary to release the accelerator pedal during gear changes.
When braking or slowing down, the gearboxchanges down automatically so that the vehiclepicks up in the right gear.
Under full acceleration, the change up will not take place unless the driver operates thegear lever or steering mounted control paddle(unless the engine is close to its maximumspeed).
Reverse
To e ngage reverse, the vehicle must be
immobilised with your foot on the brake. )
Select position R.


Stopping the vehicle

Before switching off the engine:


- chan
ge to position Nto be in neutral, or

- leave the vehicle in gear; in this case the
vehicle cannot be moved.


Manual mode
)Select position M.
The gears engaged appear in
succession in the instrument panel.
You can change mode at any time bymoving the gear lever from A
to Mor the other way round.

Never select neutral (position N ) when moving.
There is an audible signal on engagement of reverse.
For all parking situations, you must apply the parking braketo immobilisethe vehicle.

When immobilising the vehicle with the engine running, you must put the gear lever into neutral (position N)
.

Before doing anything under the bonnet, ensure that the gear lever is inneutral (position N) and that the parking brake is applied. At low speed, i
f reverse gear is requested, the
N
warning lamp flashes and the gearbox goesinto neutral automatically.
To e ngage reverse, put the gear lever into position N , then to position R.