service indicator CITROEN DS3 CABRIO 2014 Handbook (in English)
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2014, Model line: DS3 CABRIO, Model: CITROEN DS3 CABRIO 2014Pages: 384, PDF Size: 11.85 MB
Page 45 of 384

43Monitoring
System which informs the driver when the next ser vice is due, in accordance with themanufacturer's servicing schedule.
The point at which the ser vice is due is
calculated from the last indicator zero reset. It
is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service.
Service indicator
Between 600 miles (1 000 km)and 1800 miles (3 000 km) remainbefore the next service is due
For a few seconds after the ignition is switched
on, the spanner symbolising the ser vice
operations comes on. The distance recorder
displa
y line indicates the distance remainingbefore the next service is due.Example:
1 700 miles (2 800 km) remain before the next service is due.
For a few seconds after the ignition is switched
on, the screen indicates:
Less than 600 miles (1 000 km)remain before the next service is due
Example:560 miles (900 km) remain before
the next service is due.
For a few seconds after the ignition is switched on, the display indicates:
A few seconds after the ignition is switched on, the distance recorder resumes its normaloperation. The spanner remains on
toindicate that a service must be carried out soon.
A
few seconds after the ignition is switched on, the spanner goes off; the distance recorder fresumes its normal operation. The screen thenindicates the total and trip distances.
More than 1800 miles (3000 km)remain before the next service is due
When the ignition is switched on, no ser vice
information appears in the screen.
Page 46 of 384

A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation.
The spanner remains on.
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also comeon if you have exceeded the period since the last ser vice, indicated in the maintenance and warranty guide.
Service indicator zero reset
After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition, )
press and hold the trip distance recorder
zero reset button, ) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.
Following this operation, if you wish todisconnect the battery, lock the vehicleand wait at least five minutes for thezero reset to be taken into account.
Retrieving the serviceinformation
You can access the ser vice information at anytime. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for afew seconds, then disappears.
Service overdue
For a few seconds after the ignition is switchedon, the spanner flashes
to indicate that the
service must be carried out as soon as possible.Example:
the ser vice is overdue by 180 miles(300 km).
For a few seconds after the ignition is switched
on, the display indicates:
Page 47 of 384

45
Monitoring
This information is displayed for a few seconds
when the ignition is switched on, after theservice information.
Engine oil level indicator
The level shown will only be correct if the vehicle is on level ground and the engine has been off for more than30 minutes.
Oil level correct
Oil level low
This is indicated by the flashing of "OIL", linked with the ser vice warning lamp, accompaniedby an audible signal and a message in themultifunction screen.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to prevent damage to the engine.
Oil level indicator fault
This is indicated by the flashing of "OIL--"
. Contact a CITROËN dealer or a qualified
workshop.
Dipstick
Refer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.
Th
ere are 2 marks on thedipstick:-A= max; never exceed this
level (risk of damage to the engine), - B= min; top up the level via
the oil filler cap, using thegrade of oil suited to your engine.