turn signal Citroen DS3 RHD 2016 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2016, Model line: DS3 RHD, Model: Citroen DS3 RHD 2016 1.GPages: 380, PDF Size: 10.11 MB
Page 37 of 380

35
With the engine running, when the needle is:
-  i n  zone  A,
 the  temperature  is  correct,
-
Â
i
n  zone  B,  the  temperature  is  too  high; Â
t
he central STOP
Â
warning  lamp  and  the Â
m
aximum  temperature  warning  lamp 1
come
 on  in  red,  accompanied  by  an Â
a
udible  signal  and  a  message  in  the Â
m
ultifunction
 s
creen.
You must stop as soon as it is safe to do so.
Wait
 a  few  minutes  before  switching  off  the Â
e
ngine.
Contact
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop.
Coolant temperature indicator
After driving for a few minutes, the temperature and  pressure  in  the  cooling  system  increase.
To
 top  up  the  level:
F
Â
w
ait  for  the  engine  to  cool  down,
F
u
nscrew the cap by two turns to allow the
pressure
 to  drop,
F
Â
w
hen  the  pressure  has  dropped,  remove Â
t
he cap,
F
Â
t
op  up  the  level  to  the  "MA X"  mark.
Monitoring
Page 109 of 380

107
To facilitate unlocking of the steering column,  put  the  front  wheels  in  the Â
s
traight Â
a
head Â
p
osition Â
b
efore Â
s
witching Â
t
he  ignition  off.
Never
 switch  the  ignition  off  until  the
 v
ehicle  has  come  to  a  complete  stop
 a
nd  the  parking  brake  has  been  applied.
 W
ith  the  engine  stopped,  the  braking  and
 s
teering  assistance  systems  are  also  cut
 o
ff:  risk  of  loss  of  control  of  the  vehicle.When
 you  leave  the  vehicle,  take  the Â
k
ey  with  you  and  lock  the  vehicle.
For  more  information,  refer  to  the Â
"
Energy  economy  mode"  section.
Key reminder
If the key is left in the ignition switch, an audible  signal  sounds  when  the  driver's Â
d
oor  is  opened.
Switching the engine off
F Immobilise  the  vehicle.
F  W ith  the  engine  at  idle,  turn  the  key  fully Â
t
owards  you  to  position  1 (Stop).
F
Â
R
emove  the  key  from  the  ignition  switch.
F
Â
T
o  lock  the  steering  column,  turn  the Â
s
teering  wheel  until  it  locks.
F
Â
E
nsure  that  the  parking  brake  is  applied Â
c
orrectly,  particularly  when  on  a  slope.
Energy economy mode
After switching off the engine (position 1 - Stop), y
ou  can  still  use  functions  such  as  the  audio a
nd  telematic  system,  the  wipers,  dipped  beam,
 c
ourtesy  lamps,  etc.,  for  maximum  cumulative
 p
eriod  of  30  minutes.
driving
Page 118 of 380

When you move the selector in the gate to select  a  position,  the  corresponding  indicator  is Â
d
isplayed  in  the  instrument  panel.
P.
 Pa
rk
R.
R
everse
n. N
eutral
d
.
 D
rive  (Automatic  driving)
S.
Sport
 pro
gramme
T .
Snow
 pro
gramme
1 2 3 4.
 Â
G
ears  engaged  during  manual Â
ope
ration
-.
 I
nvalid  value  during  manual  operation
displays in the instrument panel
Foot on brake
F Press the  brake  pedal  when  this  i
ndicator  lamp  is  displayed  in  the Â
i
nstrument  panel  (e.g.:  starting Â
t
he
 eng
ine).
Moving off
If position n is selected inadvertently while  driving,  allow  the  engine  to Â
r
eturn  to  idle  then  select  position  d to
accelerate.
If
 the  ambient  temperature  is Â
b
elow -23°C,  the  engine  should  be  left Â
a
t  idle  for  four  minutes,  to  ensure  the Â
c
orrect  operation  and  life  of  the  engine Â
an
d
 g
earbox. When
 the  engine  is  running  at  idle,  with Â
t
he  brakes  released,  if  position  R
, d or
M  is  selected,  the  vehicle  moves  even Â
w
ithout  the  accelerator  being  pressed.
When  the  engine  is  running,  never Â
l
eave  children  in  the  vehicle  without Â
sup
ervision.
When  carrying  out  maintenance  with Â
t
he  engine  running,  apply  the  parking Â
b
rake  and  select  position  P
.
F
Â
A
pply  the  parking  brake.
F
Sel
ect position P or n
.
F
Â
S
tart  the  engine.
If
Â
this
Â
procedure  is  not  followed,  there  is  an Â
a
udible  signal,  accompanied  by  the  display  of Â
a
n
Â
warning  message.
F
Â
W
ith  the  engine  running,  press  the  brake Â
ped
al.
F
Â
R
elease  the  parking  brake.
F
Sel
ect position R
, d or M
.
F
Â
G
radually  release  the  brake  pedal.
The
Â
vehicle  moves  off  immediately.
Page 120 of 380

There is a risk of damage to the gearbox:
-  i f  you  press  the  accelerator  and Â
b
rake  pedals  at  the  same  time,
-
Â
i
f  you  force  the  movement  of  the Â
s
elector  from  the  P position to
another position when the battery
is
 flat.
To
 reduce  fuel  consumption  when  at Â
a
 prolonged  standstill  with  the  engine Â
r
unning  (traffic  jam...),  put  the  selector Â
i
n the n position  and  apply  the  parking Â
b
rake.
If the selector is not in position P
,
when
Â
the
Â
driver's
Â
door
Â
is
Â
opened
Â
or
Â
a
pproximately
Â
45
Â
seconds
Â
after
Â
the
Â
i
gnition
Â
is
Â
switched
Â
off,
Â
a
Â
warning
Â
m
essage
Â
appears
Â
in
Â
the
Â
screen.
F
R
eturn the selector to position P ;
Â
t
he
Â
message
Â
disappears.
When
Â
driving
Â
on
Â
flooded
Â
roads
Â
or
Â
when
Â
c
rossing
Â
a
Â
ford,
Â
proceed
Â
at
Â
walking
Â
p
ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f  this  warning  lamp,  accompanied Â
b
y
Â
an
Â
audible  signal  and  a  message  in  the Â
m
ultifunction  screen,  indicates  a  gearbox  fault.
In
Â
this
Â
case,  the  gearbox  switches  to  back-up Â
m
ode
Â
and
Â
is  locked  in  3rd  gear.  You  may  feel Â
a
Â
substantial  knock  when  changing  from  P
to R
Â
and
Â
from  n to R .
 This  will  not  cause  any Â
d
amage
Â
to
Â
the  gearbox.
Do
Â
not
Â
exceed  60  mph  (100  km/h),  local  speed Â
r
estrictions
 p
ermitting.
Contact
Â
a
Â
CITROËN  dealer  or  a  qualified Â
w
orkshop
Â
as  soon  as  possible.
F
Sel
ect position M for sequential c
hanging o
f
Â
the
Â
four
Â
gears.
F
Â
P
ush
Â
the
Â
selector
Â
towards
Â
the
Â
+
Â
sign
Â
to
Â
c
hange
Â
up
Â
a
Â
gear.
F
Â
P
ull
Â
the
Â
selector
Â
towards
Â
the
Â
-
Â
sign
Â
to
Â
c
hange
Â
down
Â
a
Â
gear.
It
Â
is
Â
only
Â
possible
Â
to
Â
change
Â
from
Â
one
Â
gear
Â
to
Â
a
nother
Â
if
Â
the
Â
vehicle
Â
speed
Â
and
Â
engine
Â
speed
Â
p
ermit;
Â
other wise,
Â
the
Â
gearbox
Â
will
Â
operate
Â
t
emporarily
Â
in
Â
automatic
Â
mode. This
Â
symbol
Â
is
Â
displayed
Â
if
Â
a
Â
gear
Â
i
s
Â
not
Â
engaged
Â
correctly
Â
(selector
Â
b
etween
Â
two
Â
positions).
d
Â
disappears
Â
and
Â
the
Â
gears
Â
e
ngaged
Â
appear
Â
in
Â
succession
Â
in
Â
the
Â
in
strument
 pan
el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or
nÂ
to  place  the  gearbox  in  neutral.
In
 both  cases,  apply  the  parking  brake  to Â
i
mmobilise  the  vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear  selected  flashes  for  a  few  seconds,  then Â
t
he  actual  gear  engaged  is  displayed.
It
 is  possible  to  change  from  position  d
(automatic)
 to  position  M  (manual)  at  any  time.
When
 the  vehicle  is  stationary  or  moving Â
v
ery  slowly,  the  gearbox  selects  gear  M1
automatically.
The
 sport  and  snow  programmes  do  not Â
o
perate  in  manual  mode.
Page 122 of 380

Moving off
F Apply the  parking  brake.
F Sel ect position P or n.
F
Â
S
tart  the  engine.
If
 these  conditions  are  not  met,  there  is  an Â
a
udible  signal,  accompanied  by  the  display  of Â
a
n  warning  message.
F
Â
W
ith  the  engine  running,  press  the  brake Â
ped
al.
F
Â
R
elease  the  parking  brake.
F
Sel
ect position R ,
d or M.
F
Â
G
radually  release  the  brake  pedal.
The
 vehicle  moves  off  immediately.
If position
n is  selected  inadvertently Â
w
hile  driving,  allow  the  engine  to Â
r
eturn  to  idle  then  select  position  d to
accelerate.
If
 the  ambient  temperature  is Â
b
elow -23°C,  the  engine  should  be  left Â
a
t  idle  for  four  minutes,  to  ensure  the Â
c
orrect  operation  and  life  of  the  engine Â
an
d
 g
earbox. When
 the  engine  is  running  at  idle,  with Â
t
he  brakes  released,  if  position  R,
d or
M
 is  selected,  the  vehicle  moves  even Â
w
ithout  the  accelerator  being  pressed.
When
 the  engine  is  running,  never Â
l
eave  children  in  the  vehicle  without Â
sup
ervision.
When
 carrying  out  maintenance  with Â
t
he  engine  running,  apply  the  parking Â
b
rake  and  select  position  P.
Page 124 of 380

To reduce fuel consumption when at a prolonged  standstill  with  the  engine Â
r
unning  (traffic  jam...),  put  the  selector Â
i
n the n  position  and  apply  the  parking Â
b
rake.
If the selector is not in position P
,
when
Â
the
Â
driver's
Â
door
Â
is
Â
opened
Â
or
Â
a
pproximately
Â
45
Â
seconds
Â
after
Â
the
Â
i
gnition
Â
is
Â
switched
Â
off,
Â
a
Â
warning
Â
m
essage
Â
appears
Â
in
Â
the
Â
screen.
F
R
eturn the selector to position P
;
 t
he
Â
message
Â
disappears.
When
Â
driving
Â
on
Â
flooded
Â
roads
Â
or
Â
when
Â
c
rossing
Â
a
Â
ford,
Â
proceed
Â
at
Â
walking
Â
p
ace. There
 is  a  risk  of  damage  to  the  gearbox:
- Â
i
f  you  press  the  accelerator  and Â
b
rake  pedals  at  the  same  time,
- Â
i
f  you  force  the  movement  of  the Â
s
elector  from  the  P position to
another position when the battery
is  flat.
F
Sel
ect position M for sequential
 c
hanging
 o
f
Â
the
Â
six
Â
gears.
F
Â
M
ove
Â
the
Â
selector
Â
towards
Â
the
Â
+
Â
sign
Â
to
Â
c
hange
Â
up
Â
a
Â
gear.
F
Â
M
ove
Â
the
Â
selector
Â
towards
Â
the
Â
-
Â
sign
Â
to
Â
c
hange
Â
down
Â
a
Â
gear.
It
Â
is
Â
only
Â
possible
Â
to
Â
change
Â
from
Â
one
Â
gear
Â
to
Â
a
nother
Â
if
Â
the
Â
vehicle
Â
speed
Â
and
Â
engine
Â
speed
Â
p
ermit;
Â
other wise,
Â
the
Â
gearbox
Â
will
Â
operate
Â
t
emporarily
Â
in
Â
automatic
Â
mode.
Manual operation
d disappears and the gears e
ngaged  appear  in  succession  in  the Â
in
strument
 pan
el.
If
Â
the
Â
engine  speed  is  too  low  or  too  high,  the Â
g
ear
Â
selected  flashes  for  a  few  seconds,  then Â
t
he
Â
actual
 gear  engaged  is  displayed.
It
Â
is
Â
possible  to  change  from  position  d
(automatic)
 to  position  M  (manual)  at  any  time.
When
Â
the
 vehicle  is  stationary  or  moving Â
v
ery
Â
slowly,  the  gearbox  engages  first  gear Â
au
tomatically.
Invalid value during manual
operation
This symbol is displayed if a gear i s  not  engaged  correctly  (selector Â
b
etween  two  positions).
Stopping the vehicle
Before switching off the engine, you can engage  position  P or n to  place  the  gearbox  in Â
neu
tral.
In
 both  cases,  apply  the  parking  brake  to Â
i
mmobilise  the  vehicle. When
 the  ignition  is  on,  the  lighting Â
o
f  this  warning  lamp,  accompanied Â
Operating fault
by an audible signal and a message in the m
ultifunction  screen,  indicates  a  gearbox  fault.
In
 this  case,  the  gearbox  switches  to  back-up Â
m
ode  and  is  locked  in  3rd  gear.  You  may  feel Â
a
 substantial  knock  when  changing  from  P
to R
 and  from  n to R.
 This  will  not  cause  any Â
d
amage  to  the  gearbox.
Do
 not  exceed  60  mph  (100  km/h),  local  speed Â
r
estrictions
 p
ermitting.
Contact
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop  as  soon  as  possible.
Page 143 of 380

141
The temporary illumination of the dipped beam headlamps  after  the  vehicle's  ignition  has  been Â
s
witched  off  makes  the  driver's  exit  easier Â
w
hen  the  light  is  poor.
Switching on
F With the  ignition  off,  "flash"  the  headlamps  u
sing  the  lighting  stalk.
F
Â
A
 further  "headlamp  flash"  switches  the Â
f
unction  off.
Switching off
The manual guide-me-home lighting switches off  automatically  after  a  set  time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are  switched  on  automatically,  without  any Â
a
ction  on  the  part  of  the  driver,  when  a  low  level Â
o
f  external  light  is  detected  or  in  certain  cases Â
o
f  activation  of  the  windscreen  wipers.
As
 soon  as  the  brightness  returns  to  an Â
a
dequate  level  or  after  the  windscreen  wipers Â
a
re  switched  off,  these  lamps  are  switched  off Â
a
utomatically  and  the  daytime  running  lamps Â
c
ome  on.
Automatic illumination of
headlamps
Activation
F Turn  ring  to  the  "AUTO" position.  The  a
ctivation  of  the  function  is  confirmed  by Â
t
he  display  of  a  message.
deactivation
F Turn ring  to  a  position  other  than  "AUTO".  T
he  deactivation  of  the  function  is Â
c
onfirmed  by  the  display  of  a  message.
Operating fault
In the event of a fault with the
sunshine sensor,  the  lighting  come Â
o
n,  this  warning  lamp  is  displayed Â
o
n  the  instrument  panel  and/or  a Â
m
essage  appears  in  the  screen, Â
a
ccompanied  by  an  audible  signal.
Contact
Â
a
Â
CITROËN  or  a  qualified  workshop Â
w
orkshop.
Visibility
Page 204 of 380

Important:  if  your  vehicle's  Ad
Blue® tank is completely empty - w
hich
Â
is
 confirmed  by  the  alert Â
m
essages  and  the  impossibility  of Â
s
tarting
Â
the  engine,  you  must  add  at Â
l
east
Â
3.8  litres  (so  two  1.89  litre  bottles).If
 any  additive  is  split  or  splashed,  wash Â
i
mmediately  with  cold  water  or  wipe Â
w
ith  a  damp  cloth.
If  the  additive  has  crystallised,  clean  it Â
o
ff  using  a  sponge  and  hot  water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,  signalled  by  the  message  "Top
 u
p  emissions  additive:  Starting  prevented",
 y
ou  must  wait  around  5  minutes  before
 s
witching Â
o
n Â
t
he Â
i
gnition, Â
w
ithout opening
the driver's door, locking the vehicle
or introducing the key into the ignition
switch .
Switch  on  the  ignition,  then,  after
 1
0 seconds,  start  the  engine.
F
Â
O
btain
Â
a
Â
bottle  of  AdBlue
®. After first c
hecking
Â
the
Â
use-by
Â
date,
 read  carefully Â
t
he instructions on use on the label before
pouring
Â
the
Â
contents
Â
of
Â
the  bottle  into  your Â
v
ehicle's
 Ad
Blue
® tank. N ever  dispose  of  AdBlue
® additive b
ottles
Â
in
Â
the
Â
household
Â
waste. Â Place Â
t
hem
Â
in
Â
a
Â
special
Â
container  provided Â
t
his
Â
purpose
Â
or
Â
take
Â
them
 to  your Â
d
ealer.
F
Â
A
fter
Â
emptying
Â
the
Â
bottle,
Â
wipe
Â
away
Â
any
Â
s
pillage
Â
around
Â
the
Â
tank
Â
filler
Â
using
Â
a
Â
damp
Â
c
loth.
F
Â
R
efit
Â
the
Â
blue
Â
cap
Â
to
Â
the
Â
tank
Â
and
Â
turn
Â
it
Â
a
6
th of a turn clockwise, to its stop.
F
 R
efit  the  black  cap  and  turn  it  a  quarter  of Â
a
Â
turn  clockwise  without  pressing.  Ensure Â
t
hat
 the  indicator  on  the  cap  lines  up  with Â
t
he
Â
indicator  on  the  support.
F
Â
D
epending  on  equipment,  return  the  spare Â
w
heel  and/or  the  storage  box  to  the  bottom Â
o
f
Â
the  boot.
F
Â
R
efit  the  boot  carpet  and  close  the  tailgate.