key Citroen DS5 HYBRID4 2014 1.G Owner's Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2014, Model line: DS5 HYBRID4, Model: Citroen DS5 HYBRID4 2014 1.GPages: 380, PDF Size: 13.62 MB
Page 94 of 380

DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
  Locking the front and rear passenger doors 
   Open the doors.    On the rear doors, check that the child lock is not on (see the corresponding section).    Remove the black cap, located on the edge of the door, using the key.    Insert the key in the socket without forcing it, then without turning it, move the latch sideways towards the inside of the door.    Remove the key and refit the cap.    Close the doors and check that the vehicle has locked correctly from the outside.   
  Unlocking the front and rear passenger doors 
   Pull the interior door opening control.     
Page 95 of 380

93Access
DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
            Boot 
   After unlocking the boot or the vehicle using the electronic key - remote control, press the opening control then raise the tailgate.   
  Opening  from  outside 
   Press this button until the boot is heard to unlock.   
Tailgate release 
 System allowing the mechanical unlocking of the boot in the event of a battery or central locking system malfunction. 
  If the tailgate is not closed correctly, with the  hybrid system active  or the  vehicle moving  (speed above 6 mph (10 km/h)), a message appears in the instrument panel screen for a few seconds.  
  Locking  after  closing 
 If the fault persists after closing again, the boot will  remain  locked.   
  Unlocking 
   Fold back the rear seats to gain access to the lock from inside the boot.    Insert a small screwdriver into hole  A  of the lock to unlock the tailgate.    Move the latch to the left.   
  Closing 
   Lower the tailgate using the interior grab handle.   
  Opening  from  inside  
Page 96 of 380

OFF
DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
 System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring:  
      
Alarm 
  -  Exterior  perimeter 
 The system checks for opening of the vehicle.  The alarm is triggered if anyone tries to open a door, the boot or the bonnet...    
  -  Interior  volumetric 
 The system checks for any variation in the volume in the passenger compartment.  The alarm is triggered if anyone breaks a window, enters the passenger compartment or moves  inside  the  vehicle.    
  -  Tilt 
 The system checks for any change in the attitude of the vehicle.  The alarm is triggered if the vehicle is lifted, moved  or  knocked.    
  Self-protection  function 
 The system checks for the putting out of service of its components.  The alarm is triggered if the battery, the button or the wires of the siren are put out of service or damaged.  
 For all work on the alarm system, contact a CITROËN dealer or a qualified  workshop.  
  Locking the vehicle with full 
alarm system 
  Activation 
Switch off the ignition and get out of the vehicle. 
   Press the locking button on the remote control or lock the vehicle using the Keyless Entry and Starting  system.  
 The monitoring system is active: the indicator lamp in the button flashes once per second.  After the locking button on the remote control is pressed or the vehicle locked using the Keyless Entry and Starting system, the exterior perimeter monitoring is activated after a delay of 5 seconds, the interior volumetric monitoring after 45 seconds and the anti-tilt after one minute and 30 seconds.  If an opening (door, boot...) is not closed fully, the vehicle is not locked but the exterior perimeter monitoring will be activated after a delay of 45 seconds.  
   Press the unlocking button on the remote control or unlock the vehicle using the Keyless Entry and Starting system.  
  Deactivation of the volumetric monitoring 
 The volumetric protection system is deactivated: the indicator lamp in the button  goes  off.    
Page 97 of 380

OFF
95Access
DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
  Where the vehicle locks itself again automatically (occurs 30 seconds after unlocking, if a door or the boot is not opened), the monitoring system is not reactivated automatically.  To reactivate it, the vehicle must be unlocked and locked again, using the remote control or the "Keyless Entry and Starting" system.  
  Locking  the  vehicle 
with exterior perimeter 
monitoring only 
  Deactivation of the interior volumetric and anti-tilt monitoring 
   Switch of the ignition and within ten seconds, press this button until the indicator lamp is on continuously.    Get out of the vehicle. 
   Press the locking button on the remote control immediately or lock the vehicle using the Keyless Entry and Starting system.  
 The exterior perimeter monitoring alone is activated: the indicator lamp in the button flashes once per second.  To be effective, this deactivation must be carried out each time the ignition is switched of f.  
 Deactivate the interior volumetric and anti-lift monitoring to avoid unwanted triggering of the alarm in certain cases such as:    -   leaving  a  window  partially  open,   -   washing  your  vehicle,   -   changing  a  wheel,   -   having  your  vehicle  towed,   -   transportation  by  sea.   
Page 98 of 380

OFF
OFF
DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
  Reactivation of the interior volumetric and anti-tilt monitoring 
  Triggering of the alarm 
  This is indicated by sounding of the siren and flashing of the direction indicators for thirty seconds.  The monitoring functions remain active until the alarm has been triggered eleven times in succession. 
   Press the unlocking button on the remote control or unlock the vehicle using the Keyless Entry and Starting system to deactivate the exterior perimeter monitoring. 
   Press the locking button on the remote control or lock the vehicle using the Keyless Entry and Starting system to activate all the monitoring  functions.  
 The indicator lamp in the button again flashes once per second.   
 When the vehicle is unlocked using the remote control or unlocked using the Keyless Entry and Starting system, rapid flashing of the indicator lamp in the button informs you that the alarm was triggered during your absence. When the ignition is switched on, this flashing stops immediately.   
  Failure of the remote control 
 To deactivate the monitoring functions: 
   Unlock the vehicle using the key (integral with the remote control) in the driver's door lock.    Open the door; the alarm is triggered.    Switch on the ignition; the alarm stops. The indicator lamp in the button goes off.    
  Locking the vehicle without 
activating the alarm 
   Lock or deadlock the vehicle using the key (integral with the remote control) in the driver's  door  lock.    
  Operating  fault 
  When the ignition is switched on, fixed illumination of the indicator lamp in the button indicates a fault in the system.  Have it checked by a CITROËN dealer or a qualified  workshop.   
  *    According  to  country.  
  Automatic  activation *  
  2 minutes after the last door or the boot is closed, the system is activated automatically.    To avoid triggering the alarm on entering the vehicle, first press the unlocking button on the remote control or unlock the vehicle using the Keyless Entry and Starting system.     
Page 100 of 380

DS5-HYBRID_EN_CHAP02_OUVERTURES_ED02-2013
  Safety  anti-pinch 
 When the window rises and meets an obstacle, it stops and immediately partially lowers again.  In the event of unwanted opening of the window on closing, press the switch until the window opens completely, then pull the switch immediately until the window closes. Continue to hold the switch for approximately one second after the window has closed.  The safety anti-pinch function is not active during this operation.  
  Deactivating the rear window controls 
  Reinitialisation  of  the 
electric windows 
  In the event of contact during operation of the windows, you must reverse the 
movement of the window. To do this, press the switch concerned.  When operating the passenger electric window switches, the driver must ensure that no one is preventing correct closing of the windows.  The driver must ensure that the passengers use the electric windows c o r r e c t l y.  Be aware of children when operating the windows.  Be aware of passengers or other persons present when closing the windows using the the electronic key or the "Keyless Entry and Starting" system.   
 Following reconnection of the battery, the safety anti-pinch function must be reinitialised.  The safety anti-pinch function is not active during these operations:    -   lower the window completely, then raise it, it will rise in steps of a few centimetres each time the switch is pressed. Repeat the operation until the window closes completely,   -   continue to press the switch for at least one second after reaching this position, window  closed.   For the safety of your children, press switch  5  to prevent operation of the rear windows irrespective of their position. 
 The warning lamp in the button comes on, accompanied by a message confirming activation. It remains on, as long as the child lock is activated.  The interior controls for the rear doors are also deactivated.  Opening the doors from the outside and operation of the rear electric windows from the driver's controls remain possible.    
Page 116 of 380

DS5-HYBRID_EN_CHAP03_CONFORT_ED02-2013
      
Mirrors 
  Each fitted with an adjustable mirror glass providing the lateral rear ward vision necessary for overtaking or parking. They can also be folded for parking in confined spaces.  
  Door  mirrors 
  If the mirrors are folded using control  A , they will not unfold when the vehicle is unlocked.  
  The folding and unfolding of the door mirrors using the electronic key can be 
deactivated by a CITROËN dealer or a qualified workshop.  Fold the mirrors when putting your vehicle through an automatic car wash.   
 The objects observed are, in reality, closer than they appear.  Take this into account in order to correctly judge the distance of vehicles approaching  from  behind.   
  Demisting  -  Defrosting 
  Adjustment 
   Turn control  A  to the right or to the left to select the corresponding mirror.    Move control  A  in all four directions to adjust.    Return control  A  to the central position.  
Folding 
 Automatic: lock the vehicle using the electronic key. 
  Unfolding 
 Automatic: unlock the vehicle using the electronic key. 
 Manual: with the ignition on, move control  A   downwards.  
 Manual: with the ignition on, move control  A   upwards.  
 Demisting-defrosting of the door mirrors operates by switching on the heated rear screen. 
The rear screen demisting - defrosting can only operate when the hybrid system is active.  
 For more information, refer to the "Rear screen demist-defrost"  section.  
  The mirrors can be folded manually if necessary.   
Page 169 of 380

167Visibility
DS5-HYBRID_EN_CHAP05_VISIBILITE_ED02-2013
      
Exterior welcome 
lighting 
 The remote switching on of the lighting makes your approach to the vehicle easier in poor light. It is activated according to the level of light detected by the sunshine sensor. 
  Switching  on 
  Switching  off 
  The exterior welcome lighting switches off automatically after a set time, when the ignition is switched on or on locking the vehicle.   
  Programming 
  The lighting duration is selected via the vehicle configuration menu. 
 The duration of the welcome lighting is associated with and identical to that of the automatic guide-me-home lighting.      Press the open padlock on the remote control or the door handle with Keyless Entry and Starting.  
         Door mirror 
spotlamps 
  Switching  on 
 The spotlamps come on:    -   when  you  unlock  the  vehicle,   -   when you switch off the ignition,   -   when you open a door, 
  -   when you use the remote control to locate the  vehicle.   
  Switching  off 
 They are timed to go off automatically.  
  To make your approach to the vehicle easier, these illuminate:    -   the zones facing the driver’s and passenger’s doors,   -   the zones for ward of the door mirrors and rear ward of the front doors.   
The dipped beam headlamps and the sidelamps come on; your vehicle is also unlocked.     
Page 177 of 380

175Visibility
DS5-HYBRID_EN_CHAP05_VISIBILITE_ED02-2013
1.    Front - rear cour tesy lamp2.    Front map reading lamp s 
3.    Rear map reading lamp s 4.    Interior mood LEDs
         Courtesy lamps 
 In this position, the courtesy lamp comes on gradually: 
  Front - rear courtesy lamps 
  Take care to avoid leaving anything in contact with the courtesy lamps.   
   With the "permanent lighting" mode, the lighting time varies according to the circumstances:    -   with  the  ignition  off,  approximately ten minutes,   -   in  energy  economy  mode, approximately thirty seconds,   -   with  the  hybrid  system  active,  unlimited.    
   -   when  the  vehicle  is  unlocked,   -   when the electronic key is removed from the reader,   -   when  opening  a  door,   -   when the remote control locking button is activated, in order to locate your vehicle.  
 It switches off gradually:    -   when  the  vehicle  is  locked,   -   when the ignition is switched on,   -   30 seconds after the last door is closed.  
 Permanently  off. 
 Permanent  lighting.  
  Front - rear map reading 
lamps 
   With the ignition on, press the corresponding  switch.   
Page 194 of 380

DS5-HYBRID_EN_CHAP06_SECURITE ENFANTS_ED02-2013
  The incorrect installation of a child seat in a vehicle compromises the child's protection in the event of an accident.  Ensure that there is no seat belt or seat belt buckle under the child seat, as this could 
destabilise it.  Remember to fasten the seat belts or the child seat harnesses keeping the slack relative to the child's body to a minimum, even for short journeys.  When installing a child seat using the seat belt, ensure that the seat belt is tightened correctly on the child seat and that it secures the child seat firmly on the seat of your vehicle. If your passenger seat is adjustable, move it for wards if necessary.  At rear seating positions, always leave sufficient space between the front seat and:    -   a  "rear ward  facing"  child  seat,   -   the child's feet for a child seat fitted "forward  facing".   To do this, move the front seat for wards and, if necessary, move its backrest into the upright position. 
      
Advice on child seats  
  Installing a booster seat 
  The chest part of the seat belt must be positioned on the child's shoulder without 
touching the neck.  Ensure that the lap part of the seat belt passes correctly over the child's thighs.  CITROËN recommends the use of a booster seat which has a back, fitted with a seat belt guide at shoulder level.  As a safety precaution, do not leave:    -   a child or children alone and unsupervised in a vehicle,   -   a child or an animal in a vehicle which is exposed to the sun, with the windows closed,   -   the keys within reach of children inside the  vehicle.   To prevent accidental opening of the doors and rear windows, use the "Child lock".  Take care not to open the rear windows by more than one third.  To protect young children from the rays of the sun, fit side blinds on the rear windows.   
  The legislation on carrying children on the front passenger seat is specific to each country. Refer to the legislation in force in your country.  Deactivate the passenger airbag when a "rear ward-facing" child seat is installed on the front seat.  Otherwise, the child would risk being seriously injured or killed if the airbag were to  inflate.   
  Children at the front 
 For optimum installation of the "forward-facing" child seat, ensure that the back of the child seat is as close as possible to the backrest of the vehicle's seat , in contact if possible. 
 You mst remove the head restraint before installing a child seat with backrest to a passenger seat.  Ensure that the head restraint is stored or attached securely to prevent it from being thrown around the vehicle in the event of sharp braking. Refit the head restraint when the child seat is removed.