ECO mode Citroen GRAND C4 PICASSO 2017 2.G Owner's Guide

157
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Switching on / Pause
F Turn thumbwheel 1 to the "LIMIT" position:
the speed limiter mode is selected but is
not switched on (Pause).
F

S
witch the speed limiter back on by
pressing button 4 , if the speed displayed
is suitable (by default, the last speed
programmed).
F

Y
ou can temporarily stop the speed limiter
by pressing button 4 again: the display
confirms that it has been stopped (Pause). You do not have to switch the speed limiter on
in order to set the speed.
Once the function is selected, you can modify
the speed setting by:
-

u
sing buttons 2 and 3, raising or lowering
the speed displayed:
F

b
y successive short presses, to modify
by + or - 1 mph (km/h),
F

b
y a maintained press, to modify in steps
of + or - 5 mph (km/h).
Adjusting the speed limiter
setting
- pressing button 5 :
F t he six speeds memorised are displayed
in the touch screen,
F

p
ress the button corresponding to the
limit speed chosen.
The value is displayed in the instrument panel.
The selection screen closes after a few
moments.
-

b
y pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The value is then displayed in the instrument
panel.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
4
Driving

159
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Steering mounted controls
6. Cruise control pause / resume indication.
7. Cruise control mode selection indication.
8.
Spe

ed setting.
Cruise control - "CRUISE"
System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.
The cruise control system cannot, in any circumstances, replace the need to observe speed limits, nor can it replace the need for vigilance on the part of the driver.
You are advised to keep your feet near the pedals at all times.
S
witching on the cruise control requires a
minimum vehicle speed of 25 mph (40 km/h).
As well as engagement of:
-

f

ourth gear or higher on a manual gearbox,
-

s

econd gear or higher in manual mode on
an automatic gearbox,
-

position
D on an automatic gearbox.
The system remains active after changing gear
on vehicles with a manual gearbox and Stop &
Start.
The cruise control is paused by pressing
button 4 or the brake pedal or on triggering of
the ESC system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal until the
programmed cruise speed is reached again. 1.
S
elect cruise control mode.
2.
S
et the current speed of the vehicle
as the programmed speed / Lower the
programmed speed.
3.
S
et the current speed of the vehicle
as the programmed speed / Raise the
programmed speed.
4.
P
ause / resume cruise control.
5.
D
isplay the list of memorised speeds or,
A

ccept the speed suggested by the speed
limit recognition system.
Displays in the instrument panel
Switching off the ignition cancels any
programmed speed value. For more information on Memorising speeds
,
refer to the corresponding section.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
4
Driving

160
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Exceeding the programmed
speed
If the cruise speed setting is exceeded, the
displayed speed flashes.
The display becomes steady again once the
vehicle returns to the cruise speed setting.
Switching off
F Turn thumbwheel 1 to the "0" position. T
he display of information related to the
cruise control disappears.
Switching on
Once the cruise control is switched on, you
can modify the cruising speed in one of the
following ways:
-

u
sing buttons 2 or 3 :
F

b
y successive short presses, to modify
the speed by + or - 1 mph (km/h),
F

b
y a long press, to modify the speed in
steps of + or - 5 mph (km/h),
-

b
y pressing button 5 :
F

t
he six memorised speeds are displayed
in the touch screen,
F

c
hoose a value: it is displayed in the
instrument panel.
The selection screen closes after a few
moments.
The modification is then accepted.
F

T

urn thumbwheel 1 to the "CRUISE"

position: the cruise control mode is
selected but is paused.
F
P
ress button 2 or 3 : your vehicle's current
speed becomes the cruise speed.
The cruise control is activated (ON).
Modification of the cruise speed
(speed setting)- by pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The value is then displayed in the instrument
panel.
For more information on Speed limit
recognition and memorisation, refer to the
corresponding section.
Pause
You can pause the cruise control at any time
by pressing button 4 : the screen confirms the
pause.
Driving

163
C4-Picasso-II_en_Chap04_conduite_ed02-2016
The dynamic cruise control is switched on
manually: it requires that the speed of the
vehicle be between 25 and 90 mph (40 and
150
km/h), as well as the engagement of:
-

f
ourth gear or higher with a manual
gearbox,
-

s
econd gear or higher with an automatic
gearbox in manual mode,
-
position D with an automatic gearbox.
The system remains active after changing gear
on vehicles with a manual gearbox and Stop &
Start.
General points
The dynamic cruise control can be paused
manually or automatically:
-

b
y pressing button 4 ,
-

b
y pressing the brake pedal,
-

i
n the event of operation of the ESC, for
safety reasons,
-

i
n the event of operation of the electric
parking brake control lever,
-

w
hen an inter-vehicle time threshold is
reached (calculated according to the
relative speeds of your vehicle and the
vehicle in front and the inter-vehicle time
setting chosen),
-

w
hen the distance between your vehicle
and the one in front becomes too small,
-

w
hen the speed of the vehicle in front is
too


low,
-

w
hen the speed of your vehicle becomes
too low.
The dynamic cruise control cannot in any
circumstances replace the observation
of speed limits, nor the need for vigilance
on the part of the driver.
It is recommended that you always keep
your feet close to the pedals. If the speed setting selected is above
90 mph (150 km/h), the system switches
to standard cruise control operation,
with no adjustment of the inter-vehicle
safe distance (a message appears in
the instrument panel). The inter-vehicle time setting is kept in
memory on switching off the ignition.
The dynamic cruise control operates by
day and at night, in fog or in moderate
rainfall.
The system does not act on the braking
system, but works only with engine braking.
The regulation range is limited: there will
no longer be any adjustment of speed if the
difference between the programmed speed
setting and the speed of the vehicle in front
becomes too high (18 mph (30 km/h)).
If the difference between the
programmed speed setting and the
speed of the vehicle in front is too
great, the speed cannot be adjusted:
the cruise control is automatically
deactivated.
4
Driving

164
C4-Picasso-II_en_Chap04_conduite_ed02-2016
1. Select cruise control mode.
2. Use the current speed of the vehicle as
the cruise speed setting / Lower the speed
setting.
3.
U

se the current speed of the vehicle as
the cruise speed setting / Raise the speed
setting.
4.
P

ause / Resume the cruise control.
5.
D

isplay the list of memorised speeds, or
A

ccept the speed suggested by the speed
limit recognition system.
6.
S

elect the inter-vehicle distance (" Close",
" Normal ", "Distant ")
For more information on Memorising speeds ,
refer to the corresponding section.
For more information on Speed limit
recognition and its memorisation, refer to the
corresponding section.
Steering mounted controls
Switching on
The dynamic cruise control must be selected
in the Driving menu.
F

T
urn the thumbwheel 1 to the " CRUISE"
position: cruise control mode is selected,
but is paused.
F

P
ress one of the buttons 2 or 3 : the current
speed of your vehicle becomes the cruise
speed setting.
The cruise control is activated (ON).
By default, the inter-vehicle time is set at
2
seconds.
Other wise, the last speed value set will be used
for operation of the system.
Modification of the cruise control
speed
- using buttons 2 or 3: F b y successive short presses, to modify
by steps of + or - 1 mph (km/h),
F

b
y a maintained press, to modify by
steps of + or - 5 mph (km/h).
-

b
y pressing button 5 :
F

t
he six memorised speed settings are
displayed in the touch screen,
F

c
hoose a speed setting: it is displayed in
the instrument panel.
The selection screen closes after a few
moments. The modification is then taken into
account.
-

b
y pressing button 5 , if your vehicle has
speed limit recognition:
F

t
he speed to memorise is displayed in
the instrument panel,
F
press button 5 again to save the speed.
The speed setting is then displayed in the
instrument panel.
As a precaution, it is recommended that
you select a speed setting close to the
current speed of your vehicle.
Operation
For more information on Speed limit
recognition and its memorisation, refer to the
corresponding section.
Driving

170
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Steering mounted controls
1. Select cruise control mode.
2. Use the current speed as the speed
setting
/ Lower the speed setting.
3.
U

se the current speed as the speed
setting
/ Raise the speed setting.
4.
P

ause / Resume cruise control.
5.
U

se the speed suggested by the speed
limit recognition system.
6.
D

isplay and adjust the inter-vehicle
distance setting.
For more information on Speed limit
recognition , refer to the corresponding
section.
Displays in the instrument panel
7. Indication of the presence / absence of a target vehicle.
8.
I

ndication of cruise control activation /
deactivation.
9.
Spe

ed setting.
10.
I

ndication that vehicle is held stationary.
11.
S

peed suggested by the speed limit
recognition system.
If a vehicle is detected, the symbol 7
is filled
with the colour associated with the cruise
control mode. By default, the symbol 7 is
e m pt y.
In cruise control activated mode, the symbol
8
appears in green. By default, the symbol 8
appears in grey. 12 . I
nter-vehicle distance setting.
13. P osition of the vehicle detected by the radar.
This information is visible in the instrument
panel in "DRIVING" display mode.
Driving

171
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Switching on
The cruise control is switched on manually,
it requires a vehicle speed of between 18 and
112
mph (30 and 180 km/h).
An automatic gearbox must be in position D
or M . Other wise, the last setting made will be used
when switching on the system.
Switching off the ignition cancels any
programmed speed setting.
When the cruise control is operating,
Stop & Start is automatically
deactivated.
Pause
The dynamic cruise control can be paused
manually by:
-

a
ction by the driver:
●

o
n button 4 ,
●

o
n the brake pedal,
●

o
n the electric parking brake control,
●

w
hen changing from D to N with an
automatic gearbox.
-

o
r automatically, if operation of the ESC
system is triggered for reasons of safety.
Following braking of the vehicle
bringing it to a complete stop, the
system holds the vehicle stationary;
the cruise control is paused. The driver
should press the accelerator pedal to
move off, then reactivate the system
by exceeding 18
mph (30 km/h) and
pressing button
2, 3 or 4 .
If the driver takes no action following
this immobilisation, the electric parking
brake is applied automatically after a
few minutes.
F

W

ith the ignition on, turn the thumbwheel

1
to the " CRUISE " position: cruise control
mode is selected, but not started (grey).
F

V

ehicle moving, press one of the buttons

2
or 3 : the current speed of your vehicle
becomes the cruise speed setting.
The cruise control is activated (green).
By default, the inter-vehicle distance is set at
"Normal" (2 dashes).
4
Driving

174
70
70
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Driving situations and associated alerts
To benefit from all of the information available in the instrument panel, you must first select the "DRIVING" display mode.
The following table describes the alerts and the messages displayed for the different driving situations.
The display of these alerts is not sequential.Indicator Display Associated messageComment
according to the inter-vehicle
distance selected "Cruise control paused" System paused.
No vehicle detected.
according to the inter-vehicle
distance selected "Cruise control paused" System paused.
A vehicle has been detected.
according to the inter-vehicle
distance selected "Cruise control on"
System activated.
No vehicle detected.
according to the inter-vehicle
distance selected "Cruise control on"
System activated.
A vehicle has been detected.
or "Cruise control suspended"
System activated.
The driver has temporarily taken control of the vehicle by
accelerating.
Driving

177
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Operating fault
In the event of a fault with the cruise
control, you are alerted by the
illumination of this warning lamp
and the display of a message in the
instrument panel, accompanied by an
audible signal.
The cruise control operates by day and at night, in fog or moderate rainfall.
However, it is strongly recommended that you always keep a safe distance from vehicles
ahead, depending on the driving conditions, the weather and the road sur face.
Use the cruise control only where the driving conditions allow running at a constant speed
and at an adequate safe distance.
Do not use the cruise control in urban areas, heavy traffic, on winding or steep roads, on
slippery or flooded sur faces, in snow, if the front bumper is damaged or if the brake lamps
are faulty.
In certain circumstances, it may not be possible for the speed setting to be maintained or
even attained: loaded vehicle, ascending a steep hill, etc.
The system is not intended for the following situations:
-

t

he front end of the vehicle has been modified (addition of driving lamps, paint on the
bumper),
-

d

riving on a racing circuit,
-

r

unning on a rolling road,
-

u

se of snow chains, non-slip covers or studded tyres. Have the system checked by a CITROËN
dealer or a qualified workshop.
The operation of the radar, located in the front bumper, may be disturbed by accumulations
of grime (dust, mud...) or in certain weather conditions (snow, ice...).
The message "SYSTEM INACTIVE: Visibility reduced" is displayed to signal that the system
has been put into standby.
Clean the front bumper regularly.
When painting or touching up the paint on the front bumper, consult a CITROËN dealer or a
qualified workshop. Certain types of paint could hinder the operation of the radar. The use of mats not approved by CITROËN may inter fere with the operation of the cruise
control.
To avoid any risk of jamming the pedals:
-

e

nsure that mats are secured correctly,
-

n

ever fit one mat on top of another.
4
Driving

185
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Driving situations and associated alerts
To benefit from all of the information needed in the instrument panel, you must first select the "DRIVING" display mode.
The table below describes the alerts and messages displayed according to the driving situation.
The display of these alerts is not sequential.
State of
the systemWarning
lampAssociated display
and message
Comment
OFF System deactivated.
ON System active, conditions not met:
-

s
peed below 40 mph (65 km/h),
-

n
o lane marking recognised,
-

ES
C deactivated or operation triggered,
-

"
dynamic" driving.
ON Automatic deactivation / standby of the system (for example: detection of a trailer, use of the
"space-saver" spare wheel provided with the vehicle).
ON Detection of lane markings.
Speed above 40 mph (65 km/h).
ON The system corrects the trajectory on the side concerned or the risk of involuntary crossing is
detected (orange line).
ON
"Take back the wheel". -

I
f, during correction, the system detects that the driver has not held the wheel for a few
seconds, it interrupts the correction and returns control to the driver.
-

D
uring correction of the trajectory, the system determines that the correction will not be
enough and a solid line is crossed: the driver is warned that they must complete the correction
of trajectory.
4
Driving