turn signal Citroen GRAND C4 PICASSO 2017 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2017, Model line: GRAND C4 PICASSO, Model: Citroen GRAND C4 PICASSO 2017 2.GPages: 527, PDF Size: 12.91 MB
Page 29 of 527
27
C4-Picasso-II_en_Chap01_instruments-bord_ed02-2016
Warning / indicator lampStateCause Action / Observations
Passenger's
airbag system fixed.
The control switch, located at the
right hand end of the dashboard is
set to the OFF position.
The passenger's front airbag is
deactivated.
You can install a rear ward facing
child seat, unless there is an
operating fault with the airbags
(Airbag warning lamp on). Turn the control switch to the "
ON" position to activate
the passenger's front airbag.
In this case, do not fit a child seat in the rear ward
facing position on the front passenger seat.
Collision Risk
Alert / Active
Safety Brake fixed, accompanied by
a message.
The system has been deactivated,
via the vehicle configuration menu in
the screen. For more information on the Collision Risk
Alert
/ Active Safety Brake system, refer to the
corresponding section.
Stop & Star t fixed. The Stop & Start
has been
deactivated. Reactivate the function in the Driving
menu.
Deactivation indicator lamps
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.
This is may be accompanied by an audible signal and the display of a message.
1
Instruments
Page 35 of 527
33
C4-Picasso-II_en_Chap01_instruments-bord_ed02-2016
Low fuel levelfixed, accompanied by
an audible signal and
a message. When it first comes on there remains
approximately 6 litres of fuel
in the
tank.
You are then using the fuel reserve. You must refuel as soon as possible to avoid running
out of fuel.
Until sufficient fuel is added, this warning lamp will
come on every time the ignition is switched on,
accompanied by an audible signal and a message.
This audible signal and message are repeated with
increasing frequency as the fuel level drops towards "0".
Fuel tank capacity: approximately 57 litres (petrol) or
55 litres (Diesel).
Never continue to drive until you run out of fuel as
this could damage the emission control and injection
systems.
Warning / indicator lamp
StateCause Action / Observations
Seat belt not
fastened /
unfastened fixed
or flashing
accompanied by an
audible signal. A seat belt has not been fastened or
has been unfastened.
Pull the strap then insert the tongue in the buckle.
Airbags on temporarily. This warning lamp comes on for a
few seconds when you turn on the
ignition, then goes off.
This warning lamp should go off when the engine is started.
If it does not go off, contact a CITROËN dealer or a qualified
workshop.
fixed.One of the airbag or seat belt
pretensioner systems has a fault. Have them checked by a CITROËN dealer or a
qualified workshop.
Passenger
airbag system flashing.
The passenger airbag system has a
fault. Do not have a passenger seated in the front
passenger seat.
Have it checked by a CITROËN dealer or a qualified
workshop.
1
Instruments
Page 39 of 527
37
C4-Picasso-II_en_Chap01_instruments-bord_ed02-2016
Warning / indicator lampState CauseAction / Observations
+
+ SCR emissions
control system
(BlueHDi Diesel) fixed, on switching on the ignition,
associated with the SERVICE and
engine diagnostic warning lamps,
accompanied by an audible signal and
a message. A fault with the SCR emissions control
system has been detected.
This alert disappears once the
exhaust emissions return to normal
levels.
flashing, on switching on the ignition,
associated with the SERVICE and
engine diagnostic warning lamps,
accompanied by an audible signal and
a message indicating the remaining
driving range. After confirmation of the fault with the
emissions control system, you can
drive for up to 650 miles (1 100 km)
before the engine starting inhibition
system is triggered.
Contact a CITROËN dealer or a
qualified workshop
without delay,
to avoid a breakdown .
flashing, on switching on the ignition,
associated with the SERVICE and
engine diagnostic warning lamps,
accompanied by an audible signal and
a message. You have exceeded the authorised
driving limit following confirmation
of a fault with the emissions control
system: the engine starting inhibition
system prevents starting of the
engine.To be able to start the engine, you
must
call on a CITROËN dealer or a
qualified workshop.
1
Instruments
Page 60 of 527
58
C4-Picasso-II_en_Chap02_ouvertures_ed02-2016
F Turn the key towards the rear of the vehicle to lock the vehicle completely.
Deadlocking
F Turn the key towards the rear in the driver's door lock to lock the vehicle completely.
F
T
urn the key towards the rear again within
five seconds to deadlock the vehicle.
Depending on version, the direction
indicators flash for a few seconds, the
door mirrors fold.
For versions with alarm: it is not deactivated / activated when unlocking / locking the vehicle
with the integral key.
The siren will sound on opening the door with the key (integral with the remote control). It
stops when the ignition is switched on.
Emergency procedure
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate
and in the event of a fault with the Keyless
Entry and Starting system:
-
c
ell battery flat, vehicle battery discharged
or disconnected,
...
-
v
ehicle located in an area with strong
electromagnetic signals.
F
T
o extract the emergency mechanical key
from the electronic key, press button 1 and
guide the key 2 out.
The integral key is also used to deactivate/
reactivate the passenger's airbag.
It provides a backup means of locking the
passenger doors.
It also allows locking of the vehicle without
activation of the alarm.
Emergency unlocking/locking using the integral key
F Turn the key towards the front of the vehicle to unlock the vehicle.
Depending on version, the direction
indicators flash for a few seconds, the
door mirrors unfold and the welcome
lighting comes on.
For versions with alarm: the siren will
sound on opening the door with the key
(in the remote control). It stops when
the ignition is switched on.
Unlocking Normal locking
Access
Page 136 of 527
134
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Label on door panel
Before leaving the vehicle, check
that the parking brake is applied: the
indicator lamps in the instrument panel
and the control lever must be on fixed,
not flashing.
If the parking brake is not applied, there
is an audible signal and a message is
displayed on opening the driver's door.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.When towing, parking on a steep slope,
or if your vehicle is heavily laden,
turn the wheels towards the kerb and
engage a gear (with a manual gearbox)
or place the gear selector at position
P
with an automatic gearbox.
For towing, your vehicle is approved for
parking on slopes of up to 12%.
Manual operation
Application of the parking brake
is confirmed by illumination of
the brake indicator lamp and
the
P indicator lamp in the control
lever, accompanied by the display of
the message "Parking brake applied".
Manual release
With the ignition on or the engine running, to
release the parking brake:
F
p
ress the brake pedal,
F
w
hile maintaining pressure on the brake
pedal, briefly push the control lever.
The complete release of the parking brake
is confirmed by the brake indicator lamp and
the
P indicator lamp in the control lever going
off, accompanied by the display of the message
"Parking brake released".
If you push the control lever without
pressing the brake pedal, the parking
brake will not be released and a
message is displayed.
Manual application
With the vehicle stationary: briefly pull the control lever.
Confirmation of the command is signalled by
flashing of the indicator lamp in the control
l eve r.
Driving
Page 160 of 527
158
C4-Picasso-II_en_Chap04_conduite_ed02-2016
On sharp acceleration, as when
descending a steep hill, the speed
limiter will not be able to prevent
the vehicle from exceeding the
programmed speed.
The limiter is temporarily deactivated
and the displayed programmed speed
flashes.
An audible signal accompanies the
flashing of the programmed speed
when exceeding the speed is not due to
an action by the driver.
The use of mats not approved by
CITROËN may inter fere with the
operation of the speed limiter.
To avoid any risk of jamming of the
pedals:
-
e
nsure that the mat is secured
c o r r e c t l y,
-
d
o not fit one mat on top of another.
Flashing of the dashes indicates a fault with the
speed limiter.
Have it checked by a CITROËN dealer or a
qualified workshop.
Operating fault
F Press
f irmly on the accelerator pedal,
going beyond the point of resistance ,
to
exceed the programmed speed limit.
The speed limiter is deactivated temporarily
and the displayed programmed speed flashes.
An audible signal accompanies the flashing
of the programmed speed when exceeding
the speed is not due to an action by the driver
(steep hill...).
As soon as the vehicle's speed returns to the
programmed value, the limiter operates again:
the display of the programmed speed becomes
steady again.
Switching off Temporarily exceeding the
programmed speed
F Turn the thumbwheel 1 to the "0" position. T
he display of speed limiter information
disappears.
Driving
Page 164 of 527
162
C4-Picasso-II_en_Chap04_conduite_ed02-2016
Dynamic cruise control
System that allows, in addition to maintaining your vehicle's speed at a value that you have defined, the inter-vehicle time you have selected between
your vehicle and the one in front to be maintained.
Principles of operation
Using a radar with a range of about 100 metres,
located at the front of the vehicle, this system
detects a vehicle running in front of your
vehicle.
It automatically adapts the speed of the vehicle
to that of the vehicle in front.
If the vehicle in front is running more slowly,
the system progressively reduces the speed of
your vehicle using just engine braking (as if the
driver had pressed the "-" button).
If your vehicle is too close to or approaching
the vehicle in front too quickly, the dynamic
cruise control is automatically deactivated.
The driver is then alerted by an audible signal,
accompanied by a message.
Choice of the type of cruise control
The choice between the "dynamic" and
"standard" cruise control is done in the Driving
menu.
F
I
n the Driving menu, select the " Driving
functions " tab, then " Active cruise
control" to activate or deactivate the
dynamic cruise control.
For more information on the Cruise
control , refer to the corresponding
section. F
P
lace the cruise control
thumbwheel at "CRUISE". If the vehicle in front accelerates or changes
lane, the dynamic cruise control progressively
accelerates your vehicle to return to the
programmed speed.
If the driver operates a direction indicator to
the left (left-hand drive) or the right (right-
hand drive), to overtake a slower vehicle, the
dynamic cruise control allows your vehicle to
temporarily approach the vehicle in front to
assist the overtaking manoeuvre, though never
exceeding the programmed speed.
Driving
Page 216 of 527
214
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Operation of the rear foglamps is
inhibited with the tailgate open.
Opening the tailgate when these lamps
are on causes them and their indicator
lamp in the instrument panel to go off.
They do not come back on
automatically when the tailgate is
closed: they must be switched on again
using the control stalk.In good or rainy weather, by both day
and night, the front foglamps and the
rear foglamps are prohibited. In these
situations, the power of their beams
may dazzle other drivers. They should
only be used in fog or falling snow.
In these weather conditions, you
should switch on the foglamps and
dipped beam headlamps manually,
as the sunshine sensor may detect
sufficient
light.
Do not forget to switch off the front and
rear foglamps when they are no longer
necessary.Switching off the lighting
when switching off the ignition
When the ignition is switched off, all of the
lamps switch off immediately, except for
the dipped beam headlamps if automatic
guide-me-home lighting is activated.
Switching on the lighting when
switching on the ignition
To reactivate the lighting control stalk,
turn the ring A to position "0" - lighting
off, then to the position of your choice.
When the driver's door is opened,
a
temporary audible signal warns you
that the vehicle's lighting is on.
They switch off automatically after a
period which depends on the state of
charge of the battery (entry to energy
economy mode).
Lighting and visibility
Page 217 of 527
215
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Automatic
When the automatic illumination of headlamps
is activated (lighting control stalk at the
AUTO position), if the ambient light level is
low, the dipped beam headlamps come on
automatically when switching off the ignition.
Activation or deactivation of the system, as well
as the period of operation of the guide-me-
home lighting is set via the Driving menu in the
touch screen.
Select " Guide-me-home lighting " to activate
or deactivate the function.
To adjust the period of operation, select the
symbol for the " Guide-me-home lighting "
function.
Parking lamps Guide-me-home
lighting
Manual
Deactivation
The manual guide-me-home lighting switches
off automatically after a set time. The temporary illumination of the dipped beam
headlamps after the vehicle's ignition has been
switched off makes the driver's exit easier
when the light is poor.
Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.
F
D
epending on version, within one minute
of switching off the ignition, operate the
lighting control stalk up or down depending
on the traffic side (for example: when
parking on the left; lighting control stalk
upwards; the right hand sidelamps are on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the central position. Activation
F
W
ith the ignition off, "flash" the headlamps
using the lighting stalk.
F
A f
urther "headlamp flash" switches the
function off.
5
Lighting and visibility
Page 218 of 527
216
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Automatic illumination of
headlamps
Activation
F Turn the ring to the "AUTO" position. The
activation of the function is accompanied
by the display of a message.
When a low level of ambient light is detected
by a sunshine sensor, the number plate lamps,
sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver. They can also come
on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Deactivation
F Turn the ring to another position.
Deactivation of the function is
accompanied by the display of a message.
Operating fault
In the event of a malfunction of the
sunshine sensor, the lighting comes
on; this warning lamp is displayed
In fog or snow, the sunshine sensor
may detect sufficient light. In this
case, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the top of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
Contact a CITROËN dealer or a qualified
workshop. in the instrument panel accompanied by an
audible signal and/or a message.
Lighting and visibility