brake Citroen JUMPY 2016 2.G Owner's Guide

205
Jumpy _en_Chap06_conduite_ed01-2016
Parking brake
F With your foot on the brake pedal, pull the parking brake lever up to immobilise your
vehicle.
F

W
ith your foot on the brake pedal, pull the
parking brake lever up gently, press the
release button then lower the lever fully. When parking on a slope, or on a steep
slope with a laden vehicle, turn the
wheels against the kerb then apply the
parking brake.
When the vehicle is being driven,
this warning lamp coming on,
accompanied by an audible signal
and a message, indicates that the
parking brake is still on or has not
been fully released. Pressing the brake pedal facilitates the
application and release of the manual
parking brake. If your vehicle has a manual gearbox,
engage a gear then switch off the
ignition.
If your vehicle has an automatic
gearbox, place the gear selector at
position P then switch off the ignition.
If your vehicle has an electronic
gearbox, place the gear selector at
position A then switch off the ignition.
Release on level ground Application
Anti-theft protection
Electronic engine immobiliser
The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a CITROËN dealer if required.
For reasons of safety and theft
protection, do not leave your electronic
key in the vehicle, even when you are
close to it.
It is recommended that you keep it on
your person.
6
Driving

206
Jumpy _en_Chap06_conduite_ed01-2016
Hill start assist
System which keeps your vehicle immobilised
temporarily (approximately 2 seconds) when
starting on a gradient, the time it takes to
move your foot from the brake pedal to the
accelerator pedal.
It only operates when:
-
t
he vehicle is completely stationary, with
your foot on the brake pedal,
-

t
he driver’s door is closed.
This hill start assist system cannot be
deactivated.
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.
On an ascending slope, with the vehicle
stationary, the vehicle is held for a momentarily
when you release the brake pedal.
Operating fault
F If your vehicle has a manual gearbox, place
the lever in the first gear position or in
neutral.
F

I
f your vehicle has an automatic gearbox,
place the selector at position D or select
manual operation M .
F

I
f your vehicle has an electronic gearbox,
place the selector at position A or M .If a fault in the system occurs, this warning
lamp comes on accompanied by a message.
Contact a CITROËN dealer or a qualified
workshop as soon as possible to have the
system checked.
Do not leave the vehicle while it is being
held in the hill start assist phase.
If you need to get out of the vehicle with
the engine running, apply the parking
brake manually then ensure that the
parking brake indicator lamp is on.
If your vehicle has an automatic
gearbox and you have to move off on
a steep slope (rising or falling) with a
loaded vehicle, press the brake pedal ,
select position D , release the parking
brake then release the brake pedal.
Driving

209
Jumpy _en_Chap06_conduite_ed01-2016
Automatic gearbox
Six speed automatic gearbox which offers
a choice between the comfort of automatic
operation or manual gear changing.
Two driving modes are offered:
-
a
utomatic operation for electronic
management of the gears by the gearbox,
-

m
anual operation for sequential changing
of the gears by the driver.Gear selector
P. Park.
F W ith your foot on the brake, turn the selector
to this position for parking or starting.
R.
R

everse.
F

T
urn the selector to this position.
N.
N

eutral.
F

T
urn the selector to this position for
starting.
D.
A

utomatic operation.
F

T
urn the selector to this position.
M.
M

anual operation with sequential gear
changing
F

Sel
ector in position D , press this button
then use the steering mounted control
paddles to change gear.
Steering mounted controls
The steering mounted control paddles
cannot be used to select neutral or to
select or come out of reverse.
When operating automatically, it remains
possible to change gear manually using the
steering mounted control paddles, when
overtaking, for example. Position N can be used in traffic jams or
in a car wash tunnel.
F

P

ull the right hand "
+" control paddle
towards you to change up.
F

P

ull the left hand "
-" control paddle towards
you to change down.
To turn the gear selector in complete
safety, it is recommended that you keep
your foot on the brake.
6
Driving

210
Jumpy _en_Chap06_conduite_ed01-2016
When you move the gear selector or press
the M button, the corresponding symbol
appears in the instrument panel.
P.
Pa

rk
R.


Reverse
N.


Neutral
D.
D

rive (automatic operation)
M.
M

anual operation
1 to 6.

G
ear engaged
-

I
nvalid value
Displays in the instrument panel
F With your foot on the brake, select position P . When the engine is running at idle,
with the brakes released, if position R
,
D or
M is selected, the vehicle moves
even without the accelerator being
pressed.
Never leave children in the vehicle
without supervision.
As a safety measure, never leave
the vehicle without taking your key or
remote control with you, even for a
short time.
When carrying out maintenance with
the engine running, apply the parking
brake and select position P .
If you have to move off on a steep slope
with a loaded vehicle, press the brake
pedal
, select position D , then release
the parking brake.
F

S

tart the engine.
If the conditions are not met, there is an audible
signal, accompanied by a message in the
instrument panel screen.
F

R

elease the parking brake.
F

Sel

ect position R , N or D.
F

G

radually release the brake pedal.
The vehicle moves off.
F

I

f the message " Foot on brake"
is displayed in the instrument
panel, press the brake pedal
f i r m l y.
Moving off
If P is displayed in the instrument panel
but the selector is in another position,
place the selector in position P to allow
the engine to be started.
If position N is engaged inadvertently
while driving, allow the engine to
return to idle then engage position D to
accelerate.
Driving

211
Jumpy _en_Chap06_conduite_ed01-2016
Automatic operation
Never select position N while the
vehicle is moving.
Never select position P or R unless the
vehicle is completely stationary.
Creep function (moving
without using the accelerator)
This function provides great flexibility in
manoeuvring the vehicle at low speed (when
parking, in traffic jams, …).
With the engine at idle, parking brake released
and position D, M or R selected, the vehicle
moves


as soon as you take your foot off
the brake pedal (even without pressing the
accelerator).
As a safety measure (children on
board), never leave the vehicle with the
engine running and the doors closed.
The gearbox then operates in auto-adaptive
mode, without any intervention on the part
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration, without
touching the selector press the
accelerator pedal down fully (kick-
down). The gearbox changes down
automatically or maintains the gear selected
until the maximum engine speed is reached.
On braking, the gearbox changes down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear, for
safety reasons. F
Sel
ect position D for automatic
changing of the six gears.
You can temporarily take control of gear
changes using the "+" and " -" steering mounted
control paddles. The gear change instruction is
acted on if the engine speed permits.
This function allows you to anticipate certain
situations, such as overtaking another vehicle
or approaching a bend in the road.
Following a few moments with no action on
the control paddles, the gearbox returns to
automatic operation.
Temporary manual control of
gear changes
6
Driving

212
Jumpy _en_Chap06_conduite_ed01-2016
In manual mode it is not necessary to
release the accelerator pedal when
changing gear.
F

W

ith the selector in position D ,
press button M for sequential
changing of the six gears. M appears and the gears engaged
appear in succession in the
instrument panel.
F

I
t is possible to return to
automatic operation at any time
by pressing button M again.
It is only possible to change from one
gear to another if the vehicle speed
and engine speed permit.
Manual operation
If the engine speed is too low or too
high, the gear selected flashes for
a few seconds, then the actual gear
engaged is displayed.
When the vehicle is stationary or
moving very slowly, the gearbox
selects gear M1 automatically. To save the brakes when descending
a steep incline, use engine braking to
reduce your speed (take your foot off
the accelerator pedal or change down).
Keeping the brake pedal pressed
continuously for long periods can
overheat the brakes, with the risk of
damaging the braking system or
making it inoperative.
Only use the brakes when necessary,
to slow or stop the vehicle.
The indicator associated with the button comes on.
F

O

perate the " +" or " -" steering mounted
control paddle. The indicator associated with the button goes off.
Depending on the configuration of the
road (for example: mountain pass),
it may be preferable to use manual
operation.
This is because automatic operation
may not be best suited, not allowing the
use of engine braking.
Invalid value during manual
operation
This symbol is displayed if a gear is
not engaged correctly (gear selector
between two positions).
F

P

lace the selector "correctly" at a position.
Driving

213
Jumpy _en_Chap06_conduite_ed01-2016
When the ignition is on, a message
appears in the instrument panel
screen to indicate a gearbox fault.
Operating fault
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P
to R and from N to R. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Have it checked by a CITROËN dealer or a
qualified workshop. You risk damaging the gearbox:
-

i
f you press the accelerator and
brake pedals at the same time
(braking or acceleration must be
done only with the right foot),
-
i
f you force the selector from
position P to another position when
the battery is flat.
To reduce fuel consumption when
stationary for long periods with the
engine running (traffic jam...), position
the selector at N and apply the parking
brake.
Stopping the vehicle
A stiff point may be noticed when
moving to position P .
If the selector is not in position P ,
when the driver's door is opened or
approximately 45 seconds after the
ignition is switched off, there is an
audible signal and a message appears.
F

R
eturn the selector to position P ;
the audible signal stops and the
message disappears.
Before switching off the engine, select
position


P then apply the parking brake to
immobilise the vehicle. In all circumstances, ensure that the
selector is in position P before leaving
your vehicle. On a steep slope with a loaded
vehicle, press the brake pedal
, select
position

P
, apply the parking brake then
release the brake pedal.
6
Driving

214
Jumpy _en_Chap06_conduite_ed01-2016
Electronic gearbox
R. Reverse
F T urn the selector to this position.
N.
N

eutral.
F

W
ith your foot on the brake, turn the
selector to this position for starting.
A.
A

utomatic operation.
F

T
urn the selector to this position.
M.

M
anual operation with sequential gear
changing.
F

T
urn the selector to this position, then use
the steering mounted control paddles to
change gear.
Gear selector
F Pull the right hand " +" control paddle
towards you to change up.
F

P
ull the left hand " -" control paddle towards
you to change down.
Steering mounted control paddlesElectronically controlled gearbox which offers
a choice between the comfort of fully automatic
operation and manual gear changing.
There are two driving modes:
-

a
utomatic operation for automatic control
of the gears by the gearbox, without any
action on the part of the driver,
-

m
anual operation for sequential gear
changing by the driver using the steering
mounted paddles.
With automatic operation, you can temporarily
take over control of gear changing at any time.
The steering mounted paddles cannot
be used to select neutral or to select or
come out of reverse gear.
To turn the gear selector in complete
safety, it is recommended that you keep
your foot on the brake.
Driving

215
Jumpy _en_Chap06_conduite_ed01-2016
Automatic operation
F After starting the engine, select position A for automatic gear changes
The gearbox operates in auto-active mode,
without any action on the part of the driver. It
continuously selects the most suitable gear for:
-

t
he style of driving,
-

t
he profile of the road. AUTO
and the gear engaged are
displayed in the instrument panel.
For optimum acceleration, for
example when overtaking another
vehicle, press the accelerator pedal
firmly past the point of resistance.
Display in the instrument panel
When you move the gear selector, the symbol
corresponding to its position is displayed in the
instrument panel.
Moving off
If the Foot on brake warning
lamp comes on the instrument
panel, accompanied by an
audible signal and a message
"Foot on brake", press the brake pedal
f i r m l y.
R.
R

everse
N.
N

eutral
AUTO or A.

A

utomatic operation.
M.
M

anual operation
1 to 6.

G

ear engaged
-

I

nvalid value If the engine does not star t:
If N flashes in the instrument panel,
accompanied by an audible signal
and a message, move the selector to
position A then to position N
.
F

Sel

ect automatic operation (position A),
manual operation (position M), or reverse
(position R).
F

R

elease the parking brake.
F

P

rogressively take your foot off the brake
pedal; the vehicle then moves off. N appears in the instrument panel
screen.
F

Sel

ect position N
.
F

P

ress the brake pedal down fully.
F

S

tart the engine.
6
Driving

216
Jumpy _en_Chap06_conduite_ed01-2016
Temporary manual control of
gear changes
You can temporarily take control of gear
changes using the " +" and " -" steering mounted
control paddles. The gear change instruction is
acted on if the engine speed permits.
This function allows you to anticipate certain
situations, such as overtaking another vehicle
or approaching a bend in the road.
Following a few moments with no action on
the control paddles, the gearbox returns to
automatic operation.
Manual operation
AUTO disappears and the gears
engaged are displayed successively
in the instrument panel.
F

A

fter starting the engine, select position M
for sequential gear changing
The change from one gear to another
takes place only if the conditions of
vehicles speed and engine speed
permit; if not, the automatic operation
laws are applied temporarily.
F

O

perate the "
+" or " -" steering mounted
control paddle. It is not necessary to release the
accelerator during gear changes.
When braking or slowing down, the
gearbox changes down automatically
to allow the vehicle to accelerate in the
correct gear.
On sharp acceleration, the gearbox will
not change up unless the driver acts on
the steering mounted paddles.
Never select neutral N when driving
Only engage reverse
R with the vehicle
stationary and your foot on the brake.
Driving