battery Citroen JUMPY RHD 2016 2.G User Guide

70
Changing the battery
Battery ref.: CR2032 / 3 volts.
This replacement battery is available from a
CITROËN dealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is needed.Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
F

P

lace the remote control against the
reader.
F

K

eeping it in place, switch on the ignition
by pressing "START/STOP".
The remote control is fully operational again.
Reinitialisation
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst, use the integral key in the door lock
to unlock or lock your vehicle.
F

T
hen, reinitialise the remote control.
If the problem persists, contact
a CITROËN dealer or a qualified
workshop as soon as possible.
F

U
nlock the driver's door using the
integral
key.
F

P
ress one of the remote control
buttons.
F

P
lace the integral key in the lock to unlock
your vehicle. F

U
nclip the cover using a small screwdriver
at the cutout.
F

L
ift off the cover.
F

R
emove the flat battery from its location.
F

F
it the new battery into its location
observing the original direction of fitment.
F

C
lip the cover onto the casing.
Access

86
In the case of a steep slope, the door
may be driven by its own weight and
as a consequence may open or close
j e r k i l y.
There would not be time for action at
the electric controls to take effect.
There would not be time for the
obstacle detection system to react.
Take care not to leave the vehicle on
a steep slope with the door(s) open
without supervision. If this advice is not
followed, injuries or damage may occur
if a person or an object is trapped or
caught.
On a steep slope
It is possible to open and close the doors
electrically on slopes of up to 20%.
However, if your vehicle is on a slope, with the
front of the vehicle facing up, open the door
with care. The door may open more quickly due
to the incline.
On a steep slope, guide the side door manually
to help it to close. However, if your vehicle is on a slope, with the
front of the vehicle facing down, the door may
not stay open and may close again jerkily with
the risk of injury.
Reinitialising electric doors
Following disconnection of the battery with the
doors open, it may be necessary to close the
doors manually to reinitialise them.
If the doors no longer work electrically,
reinitialise the door(s) as follows:
F

F
ully close the door(s) manually.
F

F
ully open the door(s) manually.
F

C
lose the door(s) manually.
F

F
ully open the door(s) manually.
F

C
lose the door(s) manually.
On completion of this procedure, electric
operation of the doors is restored.
However, if a problem persists following this
procedure, contact a CITROËN dealer or a
qualified workshop.
Access

94
For more information on the Key,
Remote control or Keyless Entr y and
Starting and in particular unlocking
the vehicle, refer to the corresponding
section. For more information on the Key,

Remote control or Keyless Entr y and
Starting and in particular on locking
the vehicle, refer to the corresponding
section.
Tailgate
F After unlocking the vehicle with the key, the remote control or the Keyless Entry
and Starting, pull the handle, then raise the
tailgate.
Opening
F Lower the tailgate using the interior grab handle then push it home to fully close it.
Closing Back-up control
It allows the mechanical unlocking of the
tailgate in the event of a battery or central
locking system malfunction.
Unlocking
F If fitted to your vehicle and if necessary,
fold back the rear seats to gain access to
the lock from inside.
Locking after closing
If the fault persists after closing again, the
tailgate will remain locked.
If the tailgate is not fully closed:
-

v

ehicle stationary and engine running, this
warning lamp comes on, accompanied by
an alert message for a few seconds,
-

v

ehicle moving (speed above 6 mph
(10

km/h)), this warning lamp comes on,
accompanied by an audible signal and an
alert message for a few seconds. F
I
nsert a small screwdriver into hole A of the
lock to unlock the tailgate.
F
M
ove the latch to the left.
Access

95
System which protects and provides a deterrent
against theft and break-ins.
Alarm
Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open
one of the doors or the bonnet.
Self-protection function
The system checks for the
disconnection of any of its components.
The alarm is triggered if the battery,
the button or the siren wiring is
disconnected or damaged.For all work on the alarm system,
contact a CITROËN dealer or a
qualified workshop.
VolumetricVolumetric
The system monitors the passenger
compartment for any variation in volume.
The alarm is triggered if someone breaks
the windscreen, penetrates the passenger
compartment or moves around inside the
vehicle. The system monitors variations in volume in the
cab
o n l y.
The alarm is triggered if someone breaks the
windscreen or penetrates the cab .
It is not triggered if someone penetrates the
loading area .
If your vehicle is fitted with the
programmable heating / ventilation,
volumetric monitoring is not compatible
with this system.
For more information on
Programmable Heating / Ventilation ,
refer to the corresponding section. F

L
ock the vehicle using the "Keyless Entry
and Starting" system.
Total protection
Activation
F Lock the vehicle using the remote control.
or
The monitoring system is active: the indicator
lamp in the button flashes once per second
and the direction indicators come on for about
2 seconds.
Following a command to lock the vehicle
using the remote control or the Keyless Entry
and Starting system, the exterior perimeter
monitoring is activated after a delay of
5

seconds, the interior volumetric monitoring
after 45 seconds.
If an opening (door, tailgate or side-hinged
doors, bonnet...) is not closed fully, the vehicle
is not locked but monitoring will be activated
after a delay of 45 seconds. F

Switch off the ignition and get out of the vehicle.
2
Access

98
1. Driver's electric window control
2. Passenger electric window control
Reinitialisation
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
F

L
ower the window fully, then raise it, it will
rise in steps of a few centimetres each time
the control is pressed.
F

R
epeat the operation until the window is
fully closed.
F

C
ontinue to pull the control up for at least
one second after the window closed
position has been reached.Electric windows
There are two operating modes: The safety anti-pinch function does not
operate during these operations.
Always remove the key when leaving
the vehicle, even for a short period.
If an electric window meets an obstacle
during operation, you must reverse the
movement of the window. To do this,
press the control concerned.
When the driver operates the
passenger electric window controls,
they must ensure that no one is
preventing the correct closing of the
windows.
The driver must ensure that passengers
use the electric windows correctly.
Be aware of children when operating
the windows.
Manual mode
Press or pull the control, without passing the
point of resistance. The window stops when
you release the control.
Automatic mode
Press or pull the control, beyond the point
of resistance. The window opens or closes
fully when the control is released. Pressing
the control again stops the movement of the
window.
The electrical functions of the electric windows
are deactivated:
-

a
pproximately 45 seconds after the ignition
is switched off,
-

a
fter one of the front doors is opened, if the
ignition is off.
Safety anti-pinch
If your vehicle is fitted with the safety anti-pinch
function, when the window rises and meets an
obstacle, it stops and partially lowers.
In the event of unwanted opening of the window
on closing, press the control until the window is
fully open. Within the next 4 seconds, pull the
control until the window is fully closed.
The safety anti-pinch function does not operate
during these operations.
Access

102
Electric front seat
Forwards-backwardsBackrest angleHeight
To avoid discharging the battery, carry out
these adjustments with the engine running.
For more information on the Seat belts
,
refer to the corresponding section.
F

P

ush the control for wards or rear wards to
slide the seat. F

T

ilt the control for wards or rear wards to
adjust the angle of the seat backrest. F

T

ilt the control upwards or downwards to
obtain the desired height.
Before moving the seat backwards, ensure that there is nothing that might prevent the full
travel of the seat, so as to avoid the risk of jamming the seat caused by the presence of
objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement
immediately.
Ease of use and comfort

139
F Press and hold this button to stop the heating immediately.
F

P
ress and hold this button to
start the heating immediately.
The indicator lamp in the remote control comes
on in red for about 2 seconds to confirm that
the signal has been received by the vehicle. The indicator lamp in the remote control comes
on in green for about 2 seconds to confirm that
the signal has been received by the vehicle.
Switching off Switching on
Long range remote
control
The range of the remote control is
about 0.6 miles (1 km), in open country. The indicator lamp in the remote control
flashes for about 2 seconds if the
vehicle has not received the signal.
You should then move to a different
location and repeat the command.
Changing the battery
If the indicator lamp in the remote control becomes
orange, the state of charge of the battery is low.
If the indicator lamp is not on, the battery is
discharged.
F

U
se a coin to unscrew the cap and replace
the bulb.
During heating
This indicator lamp flashes while the
heating is in operation.
This indicator lamp goes off at the end
of the heating cycle or when the heating
is stopped using the remote control.
The maximum heating period is about
45 minutes depending on the ambient
conditions.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
3
Ease of use and comfort

140
Always switch off the programmable
heating while refuelling to avoid any risk
of fire or explosion.
To avoid the risk of intoxication and
asphyxiation, the programmable
heating must not be used, even for
short periods, in an enclosed area such
as a garage or workshop not equipped
with exhaust gas extraction.
Do not park the vehicle on an
inflammable sur face (dry grass, dead
leaves, paper…), there is a risk of fire.
Glazed sur faces such as the rear
screen or windscreen can become very
hot in places.
Take care not to place objects in
contact with these sur faces, nor touch
them with your hands or any other part
of your body.
The heating is activated provided that:
-

t

he battery is sufficiently charged,
-

t

he fuel level is adequate,
-

t

he engine has been started since
the previous heating cycle.
The programmable heating system is
supplied by the vehicle's fuel tank.
Before use, ensure that there is enough
fuel in the tank.
If the tank is on reserve, it is
recommended that the system is not
used.
The ventilation is activated provided
that the battery is sufficiently charged.
Ease of use and comfort

203
The presence in the recognition zone of
the remote control of the "Keyless Entry
and Starting" system is essential.
Never leave the vehicle with the engine
running and with the remote control on
your person.
If the remote control leaves the
recognition zone, a message is
displayed.
Move the remote control into the zone
to be able to start the engine.If one of the starting conditions is
not met, a message appears in the
instrument panel screen. In some
circumstances, it is necessary to
turn the steering wheel slightly while
pressing the "START/STOP" button
to assist unlocking of the steering;
a message warns you when this is
needed. If the vehicle is not immobilised, the
engine will not stop.Switching off
F Immobilise the vehicle.
F
W
ith the remote control in
the recognition zone, press
the
"START/STOP " button.
The engine stops and the steering column is
locked.
Ignition on
(without starting)
With the ignition on, the system
automatically goes into energy
economy mode to maintain an adequate
state of charge in the battery. With the Keyless Entry and Starting
remote control inside the vehicle,
pressing the "START/STOP" button,
with no action on the pedals , allows the
ignition to be switched on.
This also allows the accessories to be used
(for

example: audio system, lighting...).
F
P
ress the "START/STOP" button,
the instrument panel comes on
but the engine does not start.
F
P
ress the button again to switch
off the ignition and allow the
vehicle to be locked.
To avoid any risk of jamming of the
pedals:
-

o

nly use mats which are suited to
the fixings already present in the
vehicle; these fixings must be used,
-

n

ever fit one mat on top of another.
The use of mats not approved by
CITROËN may inter fere with access to
the pedals and hinder the operation of
the cruise control / speed limiter.
The mats approved by CITROËN have
two fixings located below the seat.
6
Driving

204
Back-up starting
Should your vehicle not detect the electronic
key in the recognition zone, because the
remote control battery is flat, a back-up reader
is provided to the left, behind the steering
wheel to allow starting.F

P
ress the "START/STOP" button.
The engine starts. If the remote control is no longer in the
recognition zone when you close a door or
when you (later) request switching off the
engine, a message appears in the instrument
panel.
Forced switch-offRemote control not
recognised
F If you want to force switching off the
engine, press and hold the "START/STOP"
button for about 3 seconds, then contact a
CITROËN dealer or a qualified workshop.
F

I

f your vehicle has a manual gearbox, place
the gear lever in neutral then fully depress
the clutch pedal.
F

I

f your vehicle has an automatic gearbox,
place the selector at position P then press
the brake pedal firmly.
F

I

f your vehicle has an electronic gearbox,
place the selector at position N then press
the brake pedal firmly.
In the event of an emergency only and with the
vehicle stationary, you can switch off the engine.
To do this, press and hold the "START/STOP"
button for about 3 seconds.
In this case the steering column locks as soon
as the vehicle stops. F

P

lace and hold the remote control against
the reader, then:
Driving