Spare tyre CITROEN RELAY 2014 Handbook (in English)

20

Spread loads throughout the vehicle;
place the heaviest items in the bottom of
the boot, as close as possible to the rear
seats.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof
rack, bicycle carrier, trailer...). Use a roof
box in preference.
Remove roof bars and roof racks after use.


Limit the causes of excess
consumption


At the end of winter, remove snow tyres
and refit your summer tyres.

Observe the recommendations on maintenance


Check the tyre pressures regularly, when
cold, referring to the label in the door
aperture, driver's side.
Carry out this check in particular:


- before a long journey,

- at each change of season,

- after a long period out of use.
Don't forget the spare wheel and the tyres
on any trailer or caravan.

Have your vehicle serviced regularly (engine
oil, oil filter, air filter...) and observe the
schedule of operations recommended by the
manufacturer.


When refuelling, do not continue after
the 3 rd cut-off of the nozzle to avoid any
overflow.

At the wheel of your new vehicle,
it is only after the first 1 800 miles
(3 000 kilometres) that you will see the fuel
consumption settle down to a consistent
average.

150


Changing a wheel



6. REFITTING THE REPAIRED WHEEL

Refitting of the wheel is identical to step 5,
do not forget to refit the wheel trim.
Refer to the "Identification markings"
section of chapter 9 to locate the tyre
label.
The spare wheel is not designed to be used
over long distances. Have the tightening of
the bolts and pressure of the spare wheel
checked by a CITROËN dealer without
delay.
Also, have the original wheel repaired and
refitted by a CITROËN dealer as soon as
possible.


5. FITTING THE SPARE WHEEL



- Put the wheel in place on the hub and
start screwing in the bolts by hand.

- Carry out an initial tightening of the bolts
using the wheelbrace E
.

- Lower the vehicle completely by folding
the jack, then remove the jack.

- Tighten the bolts again using the
wheelbrace E
, tighten them fully without
forcing them.

- Stow the wheel to be repaired at the
rear of the vehicle.
- Hook the support H
and screw in the
handle G
.

- Insert the socket A
in the hole then
screw in the bolt, using the ratchet
wrench B
, to raise the wheel.

- Stow the tools and the trim.
Never go underneath a vehicle
supported only by a jack (use an axle
stand).
The jack and the tool kit are specific to your
vehicle. Do not use them for other purposes.

174
Exterior



EXTERIOR


Rear lamps, direction indicators, 3 rd
brake lamp, foglamps 36, 47, 153, 156


Left-hand side: fuel fi ller cap, fuel tank 144
Fuel cut-off 144


Load space 75-76
Rear doors 28



Number plate lamp 156



Parking sensors 83

Spare wheel, jack,changing a wheel,tools, puncture repair kit 148-152
Infl ating, pressures 173


Towing, lifting 162
Towbar, towball 133-134
Dimensions 164-170

Accessories 135-136
Roof bars 135
Brakes, pads 139, 141 ABS, Electronicbrake force distribution 115EBA 11 5 ASR, ESP 116-117Tyres, pressures 173Pneumatic suspension 86


Key, remote control, battery 21-23 Starting 41-42
Central locking 29
Confi dential card 25 Alarm 26


Wiper blade 161 Door mirror 77
Side repeater 155


Front lamps, foglamps, directionindicators 153-155
Headlamp beam height adjustment 49
Headlamp wash 50 Changing bulbs 153-155

Opening/closing doors 27-29
Key 23 Opening the bonnet, stay 137
Mode - autoclose 81