Mile to km CITROEN RELAY 2017 Handbook (in English)

13
Limit the causes of excess
consumption
Spread loads throughout the vehicle.
Limit the loads carried in the vehicle and
reduce wind resistance (roof bars, roof
rack, trailer...).
At the end of winter, remove snow tyres
and refit your summer tyres.
Observe the recommendations on
maintenance
Check the tyre pressures regularly, when
cold, referring to the label in the door
aperture, driver's side.
Carry out this check in particular:
-
before a long journey
,
-

at each change of season,
-


after a long period out of use.
Don't forget the spare wheel and the tyres


on any trailer or caravan.
Have your vehicle serviced regularly
(engine oil, oil filter, air filter, cabin filter...)
and observe the schedule of operations in
the manufacturer's service schedule. With a BlueHDi Diesel engine, if the SCR
has a fault your vehicle becomes polluting;
go to a CITROËN dealer or a qualified
workshop as soon as possible to bring the
levels of nitrous oxide emissions back into
line with the regulations.
When refuelling, do not continue after
the 3
rd cut-off of the nozzle to avoid any
overflow.
At the wheel of your new vehicle, it is only
after the first 1 800 miles (3 000 kilometres)
that you will see the fuel consumption settle
down to a consistent average.
1
OVErVIEW
Motoring & the Environment

23
1. Speedometer (mph or km/h).
2.
Display screen.
3.


Fuel gauge.
4.


Coolant temperature.
5.


Rev counter (rpm or tr/min x 1000).
InStruMEnt PAnELS
Level 1 display screen
In the lower part:
-
T
ime,
-

Ambient temperature,
-


Miles
/ kilometres travelled,
-

T
rip computer (range, fuel
consumption...),
-

Headlamp beam height,
-


Programmable overspeed warning,
-


Cruise control or speed limiter
,
-

Gear ef
ficiency indicator,
-

Stop & Start.
In the upper part:
-


Date,
-


Service indicator
,
-

Alert messages,
-


System status messages,
-


V
ehicle configuration.
Level 1 instrument panel

/ display screen
2
rEAdY tO GO
Instruments and controls

24
Level 2 display screen
In the left-hand part:
-
T
ime,
-

Ambient temperature,
-


Alert or state indicators,
-


Cruise control or speed limiter
.
In the right-hand part:
-

Date,
-


Service indicator
,
-

T
rip computer (range, fuel
consumption...),
-

Alert messages,
-


Messages on the state of systems,
-


V
ehicle configuration,
-

Headlamp beam height,
-


Miles
/ kilometres travelled.
Level 2 instrument panel

/ display screen
Instruments and controls

29
Warning/indicator lampisindicates Solution - action
Lane departure
warning system flashing,
accompanied by
an audible signal. unintended wander to the left.
Turn the steering wheel in the other direction to return
to the correct trajectory.
unintended wander to the
right.
Electronic
immobiliser on.
the ignition key introduced
has not been recognised
Starting is not possible. Change the key and have the faulty key checked by a
CITROËN dealer.
"Ready to go - Access" section.
on for 10 seconds
when switching on
the ignition. triggering of the alarm.
Have the state of the locks checked by a CITROËN
dealer or a qualified workshop.
Water in Diesel
fuel filter on, accompanied
by a message in
the screen.
there is water in the fuel filter. Have the filter bled by a CITROËN dealer or a qualified
workshop.
"Checks - Levels and checks" section.
AdBlue on, then flashing,
accompanied by
a message in the
screen. reduced driving range. Have the AdBlue topped-up without delay.
Do not wait until the remaining range is 0 miles, you will
not be able to restart the engine!
"Checks - AdBlue" section.
Low fuel level on with the needle
in zone E.
the fuel reserved is being
used. Refuel without delay.
The calculation of the remaining fuel depends on the
style of driving, the profile of the road, the time elapsed
and the distance travelled since the warning lamp first
came on.
flashing. a fault with the system. Contact a CITROËN dealer or a qualified workshop.
2
rEAdY tO GO
Instruments and controls

34EMISSIOnS cOntrOLS
EOBD (European On Board Diagnosis) is
a diagnostics system which complies with,
among others, the standards on emissions
limits of:
-
CO (carbon monoxide),
-


HC (unburnt hydrocarbons),
-


NOx (nitrogen oxides), detected by

oxygen sensors placed downstream of
the catalytic converters,
-

particles.
tYrE undEr-InFLAt IO n d E t E ct IO n
System which automatically checks the
pressures of the tyres while driving.
The tyre under-inflation detection
system is an aid to driving which does
not replace the need for vigilance on
the part of the driver. This system does not avoid the need
to check the tyre pressures regularly
(including the spare wheel) and before a
long journey.
Driving with under-inflated tyres increases
fuel consumption.
The system continuously monitors the
pressures of the four tyres, as soon as the
vehicle is moving.
A pressure sensor is located in the valve of
each tyre.
The system triggers an alert if a drop in
pressure is detected in one or more tyres. The tyre pressures must be checked
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6 miles (10 km) at moderate speed).
Otherwise, add 0.3 bar to the values
indicated on the label.
The tyre pressures for your vehicle can be
found on the tyre pressure label.
The driver is warned of any
malfunction of this emissions
control system by the illumination
of this warning lamp in the
instrument panel.
If this warning lamp comes on, have it
checked by a CITROËN dealer or a qualified
workshop.
To locate it, refer to the "Technical
data
- Identification markings" section.
Driving with under-inflated tyres
adversely affects road holding, extends
braking distances and causes premature
tyre wear, particularly under arduous
conditions (vehicle loaded, high speed, long
journey).
Instruments and controls

37
Refer to the "Technology on board -
Vehicle configuration" section.
reminder of servicing information
At any time, to access the service indicator,
press briefly on the MOd E button.
Use the up/down arrows to see the
scheduling and engine oil wear information.
Pressing the MO
d E button again allows you
to return to the various display menus.
A long press returns you to the main menu.
Menu...
c

hoose...
Allows you to...
11
Service Service
(miles/
km before
service)
Display the
distance
remaining
before the
next service.
Oil (miles/
km
before oil
change) Display
the miles/
kilometres to
the next oil
change.
Refer to the list of checks in the
manufacturer's service schedule which
was given to you on handover of the
vehicle.
resetting the servicing information
The continuous flashing of the indicator is
stopped by a qualified workshop using a
diagnostic tool, after each service.
If you have carried out the service on your
vehicle yourself, you can reset the service
indicator as follows:
F
insert the ignition key into the switch,
F
turn it to the

MA r position,
F
simultaneously press the brake and


accelerator pedals for more than
15
seconds.
2
rEAdY tO GO
Instruments and controls

94Menu…Press... Sub-menu… Press... Select…c onfirm
and quit Enables you to...
8 Measurement
unit (Unit)
Distance Km
Select the distance display unit.
Miles
Fuel
consumption km/l
Select the fuel consumption
display unit.
l/100 km
Temperature °C
Select the temperature display
unit.
°F
9
Languages List of


languages
available Select the display language.
10 Volume of
announcements
(Buzz)Increase Increase / Decrease the volume
of the announcements or of the
audible warning.
Decrease
11
Service Service (Miles/
km before


service) Display the miles/kilometres
remaining before the next
service.
Oil (Miles/Km
before oil
change) Display the miles/kilometres to
the next oil change
Vehicle configuration

97From the "Safety / Help" sub menu, you can:
-
select "Parkview Camera", then

"Reversing camera" to activate or
deactivate its use (On, Off),
-

select "Parkview Camera", then

"Camera delay" to activate or deactivate
the maintaining of the display for
10
seconds or up to 11 mph (18 km/h)
(On, Off),
-

select "T
raffic Sign" to activate or
deactivate its use (On, Off),
-

select "Passenger airbag" to activate or

deactivate its use (On, Off).
From the "Lighting" sub-menu, you can:
-

select "Daytime running lamps" to

activate or deactivate their use (On, Off),
-

select "Auto headlamp dipping" to

activate or deactivate its use (On, Off),
-

select "Headlamp sensor" to adjust its

sensitivity (1, 2, 3). From the "Doors & locking" sub-menu,
you
can:
-

select "Autoclose" to activate or

deactivate its use (On, Off).
From the "Display" sub-menu, you can:
-

select "Languages" and choose one of


the languages listed above,
-

select "Units of measurement" to


choose the units for fuel consumption
(l/100

km, mpg), distance (miles, km)
and temperature (°C, °F),
-

select "Display

Trip B" to switch trip B
On or Off in the trip computer.
From the "Time and Date" sub-menu, you
can:
-

select "Adjust time and format" to set the


hour, minutes and seconds and choose
the format (24 h, 12 h with am or pm),
-

select "Adjust Date" to set the day

,
month and year.
To set the time manually, "Synch Time"
must be Off.
4
TECHNOLOGYon BOARD
V

98
The trIP button, located at the end of the
wiper control stalk, gives access to the
following information:
-
r
ange
This indicates the distance that can still


be travelled with the fuel remaining in
the tank on the basis of the average
consumption over the last few miles
(kilometres) travelled. -
A verage speed A

This is the average speed calculated


since the last trip computer zero reset
(with the ignition on).
-
t
rip

duration A
This indicates the total time since the


last trip recorder zero reset.
-

d istance A

This indicates the distance travelled


since the last trip computer zero reset.
-

A
verage fuel consumption A
This is the average quantity of fuel


consumed since the last trip computer
zero reset.
-
c
urrent fuel consumption A
This is the average quantity of fuel


consumed during the last few seconds.
trIP c OMP ut E r
If TRIP B is activated in the MOdE menu:
-
Distance B
-


A
verage fuel consumption B
-

A
verage speed B
-

T
rip duration B
Vehicle data

106
Good practice
The ABS system does not provide shorter
braking distances. On very slippery surfaces
(black ice, oil...) the ABS can extend braking
distances. For emergency braking, press the
brake pedal hard and do not release it, even
on a slipper surface; you will then be able to
steer the vehicle and avoid an obstacle.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations.Emergency braking assistance
System which, in an emergency, enables
you to obtain the optimum braking pressure
more quickly, thus reducing the stopping
distance.
Operation
It is triggered by the speed at which the
brake pedal is pressed.
The effect of this is a reduction in the
resistance of the pedal and an increase in
braking efficiency.
Switching off
This system cannot be deactivated by
the driver.
Operating fault
If this warning lamp comes on,
accompanied by an audible signal
and a message in the instrument
panel screen, it indicates a fault with
the anti-lock braking system which could result in
loss of control of the vehicle when braking.
For maximum braking efficiency, a
bedding-in period of around 300 miles
(500 kilometres) is needed. During this
period it is recommended that you avoid
harsh, repeated or prolonged braking. If this warning lamp comes on,
together with the ABS warning
lamp, accompanied by a message
in the instrument panel screen,
it indicates a fault with the electronic brake
force distribution which could result in loss
of control of the vehicle when braking. When braking in an emergency, press
firmly without releasing the pressure.
You must stop as soon as it is safe to do so.
In either case, contact a CITROËN dealer or
a qualified workshop.
driving safely