Downloaded from www.Manualslib.com manuals search engine 448
BRAKESBRAKE SPECIFICATIONS
Electrical circuit
ComponentsRef.
SupplierPart no.Observations
42 wayconnector.
Integral to the hydraulic block..Changing only the ECU is prohibited.
2 waygrey connector.
The sensors are inductive type.Tightening torque:
0,8 ± 0,2 m.daN.
2 waygrey connector.
The sensors are inductive type.Mounted on the brake caliper support.
Non adjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
2 waygrey connector.
The sensors are inductive type.
Mounted on the suspension arm.
Non adjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
Incorporated in the COM 2000.
6 wayblue connector.
Located on the central console.
6 way connector.
Toothed wheel:
48 teeth.
Integral with the driveshaft stub housing for
the front wheels, joined to the hub bearing for
the rear wheels.
XSARA
5.7 ESP
0 265 006 389
0 265 006 202
0 265 006 203
0 265 006 441 BOSCH
VALEO
BOSCH
GKNElectronic
ECU
Front wheel sensor
Rear wheel sensor
(disc brakes)
Rear wheel sensor(Saloon: drum brakes)
Rear wheel sensor(Estate: drum brakes)
Steering angle sensor
Gyrometer/accelerometer sensor
Toothed wheel7
5
12
13
4
Downloaded from www.Manualslib.com manuals search engine 457
BRAKES
B3FP11XD
HANDBRAKE (Adjustment)
XSARA PICASSO
Adjustment.
Remove the handbrake trim (1).
Unclip the sound deadening (2).
Raise and support the vehicle with the rear wheels
hanging free.
Check the correct routing of the brake cables under the
vehicle.
Apply and release the handbrake
4 times.
Set the handbrake to the 5th notch.
Tighten the nut
(3)until the rear brakes are applied.
Pull the handbrake lever vigorously 4 to 5 times.
Set the handbrake to the 5th notch.
Check that the rear brakes are applied.
With the handbrake released, check that the wheelscan be turned freely by hand.
Lower the vehicle.Refit the sound deadening
(2)and the handbrake trim (1).
Downloaded from www.Manualslib.com manuals search engine 495
AIRCON
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Changing the filtering/drying cartridge
Move aside the radiator/condenser assembly.
Remove the plug (6), using tool [2].
Support the radiator/condenser assembly thus moved aside.
Remove the filtering/drying cartridge
(7), using pliers.
Refitting.Refit the filtering/drying cartridge (7).
Clean the threads of the plug (6).
It is essntial to change the O ring seals (8).
Lubricate the O ring seals (8)with aircon compressor oil.
Refit:
The plug
(6), using tool [2], tighten to 1,4 ±0,2 m.daN.
The brackets (5).
The screws (4).
The cardboard from the radiator harness.
The nuts
(1).
The air filter assembly (3).
Couple the hose (2).
Recharge the circuit (R134.a) (according to equipment)
(see corresponding operation).
Check the operation of the air conditioning.
C5HP14NCC5HP14PCC5HP14QC
XSARA PICASSO
