wheel bolts DACIA LODGY 2012 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine towing hitch........................................... (up to the end of the DU)
jack ....................................................... (up to the end of the DU)
wheelbrace ........................................... (up to the end of the DU)
hubcap tool ........................................... (up to the end of the DU)
5.2
ENG_UD28039_2
Outils (X92 - Renault)
ENG_NU_975-3_X92_Dacia_5
Tools
Tools
Accessing the toolsThe tools are located in the luggage
compartment.
The presence of the tools depends on
the vehicle.
Jack 1To use the jack, unscrew nut 5 . When
replacing the jack, fold it up completely
and replace it in its housing. Tighten the
nut 5 to secure the jack.
Hubcap tool 2Removes the wheel hubcaps. Located
behind the jack.
Tow eye 3Please see “Towing: breakdown recov-
ery” in Section 5.
5
Never leave tools unsecured in the vehicle: there is a risk that they may
be thrown about during braking. After use, make sure the tools are cor-
rectly positioned in their housings: there is a risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the
emergency spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to gain access
to the underside of the vehicle.
1
2
34
Wheelbrace 4This is used to tighten/loosen the wheel
bolts and, depending on the vehicle, to
access the emergency spare wheel.
1
2
3
4

Downloaded from www.Manualslib.com manuals search engine 5.4
ENG_UD24468_1
Crevaison (X92 - Renault)
ENG_NU_975-3_X92_Dacia_5
Emergency spare wheel 2
This is stored in cage 4 under the floor
at the rear of the vehicle.
To access the emergency spare
wheel
– Open the tailgate;
– Undo the nut with wheelbrace 1
stored in the boot;
– Detach the cage 4 using handle 3;
– Release the emergency spare
wheel.
PUNCTURE (2/2)
To store the wheel in the cage
– Make sure the wheel is correctly po-
sitioned in the cage 4 , valve facing
down.
– Re-attach the subframe using
handle 3 and retighten the nut using
spanner 1 to refit the assembly.
– Make sure it is correctly locked.
If the cage 4 cannot be re-attached, this
means that the wheel is poorly posi -
tioned. If this happens, open the cage,
push the wheel in as far as it will go and
close again.
1
2
34
1
Do not leave the tools un -
secured inside the vehicle
as they may come loose
under braking. After use,
make sure the tools are correctly
positioned in their housings: risk of
injury.
If wheel bolts are supplied in the
tool kit, only use these bolts for the
emergency spare wheel: refer to the
label affixed to the emergency spare
wheel.
The jack is designed for wheel
changing purposes only. Under no
circumstances should it be used for
carrying out repairs underneath the
vehicle or to gain access to the un-
derside of the vehicle.
Do not touch the exhaust as
it could burn.

Downloaded from www.Manualslib.com manuals search engine trims ...................................................... (up to the end of the DU)
5.8
ENG_UD24470_1
Enjoliveurs - Jantes (X92 - Renault)
ENG_NU_975-3_X92_Dacia_5
Wheel trim – Wheel rims
WHEEl TRIM - WHEEls
Wheel trim with concealed
wheel bolts
Remove the wheel trim using the
hubcap tool 1, by inserting the tool into
valve recess 2.
To refit the wheel trim, align it with
valve 2 . Push the retaining hooks in
fully, starting with side A near the valve,
followed by B and C, finishing at D op-
posite the valve.
1
A
BC
D
2
Wheel trim with visible wheel
bolts
To remove it without removing the
wheel, press it at the points indicated
by the arrows.
Turn it so that the retaining brackets
holding it in place behind the wheel
bolts are released.
To refit the hubcap, proceed in reverse
order.
Anti-theft bolts
If you use anti-theft bolts,use the in-
structions on the inside of the wheel
trim to position the bolts (wheel trim
may not be able to fit).

Downloaded from www.Manualslib.com manuals search engine changing a wheel.................................. (up to the end of the DU)
jack ....................................................... (up to the end of the DU)
puncture ................................................ (up to the end of the DU)
lifting the vehicle changing a wheel ............................ (up to the end of the DU)
5.9
ENG_UD27017_2
Changement de roue (X92 - Renault)
ENG_NU_975-3_X92_Dacia_5
Place the jack 4 horizontally; the jack
head must be lined up with the sill 1
closest to the wheel concerned, as
shown by arrow 2.
Crank up the jack 4 by hand at first to
align the base plate (which should be
inclined further inwards than the jack
head).
Turn the wheelbrace until the wheel lifts
off the ground.
Changing a wheel
CHANGING A WHEEl (1/2)
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the hubcap.
Use the wheelbrace 3 to slacken off
the wheel bolts. Fit it so that you press
downwards rather than pulling up -
wards.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level sur -
face where it will not slip (if neces -
sary, place a solid support under the
jack base).
Apply the parking brake and engage
a gear (first or reverse).
Ask all passengers to leave the ve-
hicle and keep them away from traf-
fic.
1
23
4

Downloaded from www.Manualslib.com manuals search engine 5.10
ENG_UD27017_2
Changement de roue (X92 - Renault)
ENG_NU_975-3_X92_Dacia_5
Undo the bolts and take off the wheel.
Fit the emergency spare wheel on the
central hub and turn it to locate the
mounting holes in the wheel and the
hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel.
Tighten the bolts, checking that the
wheel is correctly positioned on its hub
and lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness
of the bolts checked (tightening torque:
110 N.m) and the emergency spare
wheel pressure checked as soon as
possible.
CHANGING A WHEEl (2/2)
If you have a puncture, re -
place the wheel as soon
as possible. A tyre which
has been punctured should
always be inspected (and repaired,
where possible) by a specialist.
Anti-theft bolts
If you use anti-theft bolts, please
refer to the instructions given on
the interior of the wheel trim to posi-
tion the bolts (wheel trim may not be
able to fit).