wheel bolts DACIA SANDERO 2013 2.G Owners Manual
[x] Cancel search | Manufacturer: DACIA, Model Year: 2013, Model line: SANDERO, Model: DACIA SANDERO 2013 2.GPages: 146, PDF Size: 6.4 MB
Page 103 of 146
towing hitch...........................................(up to the end of the DU)practical advice .....................................(up to the end of the DU)jack .......................................................(up to the end of the DU)lifting the vehiclechanging a wheel ............................(up to the end of the DU)wheelbrace ...........................................(up to the end of the DU)
5.3
ENG_UD5598_1Outils (B90 - Dacia)ENG_NU_817-2_NU_Dacia_5
Towing hitch 1
Refer to the information on “Towing: breakdown” in Section 5.
Outils (Cric - Manivelle, etc.)
TOOLS
The tools are stored in the luggage compartment.
Do not leave the tools unse- cured inside the vehicle as they may come loose under braking. After use, ensure the tools are correctly stored: risk of injury.
Wheelbrace 2
This is used to tighten or release the wheel bolts.
Jack 3
To use the jack, undo bolt 5.
When replacing the jack, fold it up com- pletely and replace it in its housing.
Hubcap tool 4
This tool is used to remove the wheel trims.
The jack is designed for wheel changing purposes only. Under no circum- stances should it be used for carrying out repairs underneath the vehicle or to gain access to the
underside of the vehicle.
3
12
2
13
5
4
4
Page 104 of 146
practical advice .....................................(up to the end of the DU)trims ......................................................(up to the end of the DU)lifting the vehiclechanging a wheel ............................(up to the end of the DU)
5.4
ENG_UD5599_1Enjoliveurs - Jantes (B90 - Dacia)ENG_NU_817-2_NU_Dacia_5
JauneNoirNoir texte
Central wheel trim with
concealed wheel bolts
Remove the wheel trim using the
hubcap tool by inserting the tool 4 into
valve recess 3.
To refit the wheel trim, align recess
3 with the wheel rim, clip the wheel trim
back in place and use tool 4 to tighten the nut.
Enjoliveurs - jantes
WHEEL TRIM - WHEELS
Wheel trim with concealed
wheel bolts
Remove the wheel trim using the
hubcap tool 1, by inserting the tool into
valve recess 2.
To refit it, align it with valve
2. Push the retaining hooks in fully, starting
with side A near the valve, followed
by B and C, finishing at D opposite the
valve.
We would advise you to note the
number engraved on the tool so that you can replace it if it is lost.
B
D
C
A
123
4
Page 105 of 146
JauneNoirNoir texte
5.5
ENG_UD5599_1Enjoliveurs - Jantes (B90 - Dacia)ENG_NU_817-2_NU_Dacia_5
WHEEL TRIM - WHEELS (continued)
Central wheel trim with
concealed wheel bolts
Remove it using the hubcap tool 1, in-
serting the tool into recess 5 provided.
To refit it, turn it so that it is aligned with the rim and clip it in place.
Central wheel trim with
visible wheel bolts
6
To remove it without removing the wheel, press it at the points indicated by the arrows.
Turn it so that the retaining brackets holding it in place behind the wheel bolts are released.
To refit the hubcap, proceed in reverse order.
15
6
Page 106 of 146
changing a wheel..................................(up to the end of the DU)practical advice .....................................(up to the end of the DU)jack .......................................................(up to the end of the DU)puncture................................................(up to the end of the DU)lifting the vehiclechanging a wheel ............................(up to the end of the DU)
5.6
ENG_UD5600_1Changement de roue (B90 - Dacia)ENG_NU_817-2_NU_Dacia_5
Changement de roue
CHANGING A WHEEL
Park the vehicle away from traffic and on level ground which is not slippery (place a plank under the jack if necessary). Switch on the hazard warning lights.
Apply the hand brake and engage a gear (first or reverse).
Ask all the passengers to leave the vehicle and keep them away from traffic.
If you have a puncture, re-
place the wheel as soon as possible.
A tyre which has been punc- tured should always be inspected (and repaired, where possible) by a specialist.
Remove the wheel trim (refer to the in- formation on “Wheel trims”).
Use the wheelbrace
1 to slacken off the wheel bolts. Fit it so that you press downwards rather than pulling up- wards.
Present the jack horizontally, the jack head must slide in the lower slot in the body, as close as possible to the wheel concerned.
Crank up the jack
2 by hand to align the base plate (slightly inwards under the vehicle). Place a plank of wood under the base plate if on soft ground.
Turn the wheelbrace until the wheel lifts off the ground.
Remove the bolts.
Take off the wheel.
Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.
If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
Tighten the bolts, checking that the wheel is correctly positioned on its hub and lower the jack.
With the wheels on the ground, tighten the nuts as fully as possible and check the tightness as soon as possible (tight- ening torque 105 Nm).
1
2