light DACIA SOLENZA 2004 Owners Manual

84
STEERING - CONN ECTOR
84 - 11
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the upper part dashboard.
Disconnect connectors ( 1), (2) and (3). Mark identification of their mounting position.
Holding with one hand the fix part ( 4) dismount the lighter attachment clamp ( 5) on the lower
part dashboard. Extract the lighter fix body (part).
REMOU NT I NG
Position the lighter fix body in the dashboard lower part. Holding with one hand the fix body,
mount the lighter attachmen t clamp. The required tightening moment is 1.5 Nm applied to the fix
body (4). Connect the lighter connectors, observing their mounting position existent prior to dismount-
ing. Mount the upper part dashboard.
Reconnect the battery (-) terminal.
Check the operation of the electric lighter.
REMARK:
In order to replace the bulb, dismount the lighter, dismount the bulb holder (6) from
the clamp (5) and replace the bulb.
Connectors
Connector Denomination 1 Mass
2 Supply + after contact
3 Supply + parking
Electric lighter
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 7
Diagnostic - General
Subject to equipment level, two types of Cockpit Central Unit may be mounted:
Cockpit Central Unit
Diagnostic connection
Coded anti-starting (V2)
Turning lights and indicator management
Acoustic warning (turning lights on forgetfulness)
Windscreen wiper: fix point stopping management
Cockpit lighting management
Cockpit timing lighting
Doors electric blocking by radio-frequency
Alarm connection Ba
sic range
N2
X
X
X
X
X
X High range
N4
X
X
X
X
X
X
X
X
X
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 8
Diagnostic - General
CONNECTION (the most complete)
Black connector EH1 ( 40 pins)
PIN DENOMINATION 1Not used
2Not used
3Not used
4Not used
5 Not used
6 Not used
7 Not used
8D oors locking switch inlet
( doors unlocking control)
9Not used
10 Not used
11 N o t u s e d
12 Not used
13 Not used
14 Not used
15 Parking lights inlet
16 Decoding bushing inlet
17 Doors locking switch inlet
(doors locking control)
18 Not used
19 Not used
20 Not used
21 Not used
22 + After contact
23 Not used
24 Windscreen wiper timer inlet
25 Not used
26 Left turning inle t
27 Not used
28 Right turning inlet
29 Not used
30 Not used
31 Not used
32 Anti-starting indic ator inlet
33 Hazard lights inlet
34 Diagnostic line K
35 Not used
36 Engine anti-starting outlet
37 Not used
38 Not used
39 Not used
40 Driver’s door contact inlet White connector P1 (15 pins)
PIN DENOMINATION
A1 Mas s
A2 Ceiling lamp outlet
A3 + Before contact
A4 Windscreen wiper control
A5
Windscreen wiper supply (+ after
contact)
A6 Windscreen wiper fix point stopping
A7 Not used
A8 Right turning outlet
A9 Left turning outlet
B1 Not used
B2 Doors locking outlet
B3 Doors locking/unlocking supply
B4 Doors unlocking outlet
B5 Ceiling amp timer outlet
B6 Ceiling lamp supply
P1 EH1
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 14
Diagnostic - Conformity checking
RECOMMENDATIONS Do not perform this conformity checking but after a competechecking by means of diagnostic tester. The values
displayed in this conformity checking are only informative.
The execution condition: stopped engine, contact set on.
1
2 Supply
Lighting PR002
: Battery voltage
ET002: +12 V after
c ontact
ET309: Right turning
information
ET310: L eft turning
information
ET291: H azard lights
information 12V < X
< 12,5V
Presen t
It is ACTIVE when
c ontrolling r ight
turning
It is ACTIVE when
controlling left turning
It is ACTIVE when
controlling hazard lights If problems occurring:
Perform a diagnostic of the charging circuit
If problems occurring: See state diagnostic
ET002
If is INACTIVE , see
state diagnostic ET309
If it is INACTIVE , see
state diagnostic ET310
If it is INACTIVE , see
state diagnostic ET291
No.
Function Par
ameter or state
Checking or action Visualization and
observations
Diagnos tic
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 20
Diagnostic –States interpretation
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
ET291
HAZARD LIGHTS INFORMATION
RECOMMENDATIONS No failure must be present or memorized.
Act upon the hazard lights switch.
State must be
ACTIVE
ET291 INACT IVE
Check supply fuse F 13 (25A) fo r turning / Cockpit Central Unit.
Replace it if necessary.
Check connection and condition of the hazard lights contact
connector Repair the connector if necessary.
Check continuity of the connection:
Hazard lights contact pins 5 and 6 mass
Fix if necessary.
Check
insulation, continuity and absence of parasite resistance
of the connection:
Hazard lights contact pin 8 pin
B33 EH1 connector
with 40 pins
Fix if necessary.
Check operation of hazard lights control
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 21
ET309
ET310RIGHT TURNING INFORMATION
LEFT TURNING INFORMATION
Diagnostic – States interpretation
No failure must be present or memorized.
RECOMMENDATIONS Set on the contact Act upon the left or right turning control
State must be ACTIVE
Check the supply fuse F13 (25A) for turning lights/Cockpit Central
Unit.
Replace it if necessary.
Check connection and condition of the turning switch connector.
Fix is necessary.
Ensure continuity of the connection:
Turning switch pi n 6 mass
Fix if necessary
Di sconnect connector EH1 40 pins of UCH
Ensure continuity and insulation of the connections:
Right turning switch pin 5
pin B28 connector
EH1 40 pins UCH
Left turning switch pin 7
pin B26 connector
EH1 40 pins UCH
Fix is necessary.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
ET309
ar
ET310
INACTIVE
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 25
Diagnostic – States interpretation
ET257PARKING LIGHTS INFORMATION
RECOMMENDATIONS Check that no failure is present or memorized. Act upon the parking lights control.
State must be ACTIVE, and the parking lights on
Check the bulbs.
Check parking lights fuse F14 (7.5 A)
Replace it if necessary
Check connection and c ondition of UCH connector EH1 40 pins .
Replace the connector if necessary
Ensure continuity and insulation of the connection:
pin A15 connector EH1 40 pin sfuse box, parking
lights fuse (7.5A)
Fix if necessary.
ET257
INACTIV
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 26
Diagnostic – Damage location algorithm
RECOMMENDATIONSDo not consult these information but after a complete
checking by means of CLIP te ster
THERE IS NO COMMUNI CATION WITH THE COMPUT ER AL P1
LIGHTING
TURNING LIGHTS ARE NOT WORKING AL P2
PARKING LIGHTS ARE NOT WORKING AL P3
WINDSCREEN WIPING WINDSCREEN WIPER L OW SPEED NOT WORKING AL P4
WINDSCREEN WI PER HIGH SPEED NOT WORKING AL P5
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 28
Diagnostic – Damage location algorithm
ALP 2Turning lights not working
RECOMMENDATIONS Do not consult these information but before a complete
checking by means of the CLIP tester.
Check the bulbs
Check the condition of fuse F13 (25A) and replace it i f necessary.
Pu sh the hazard switch and check that state <> is
ACTIVE ; if not, refer to chapter dealing with this state.
Act upon the right or left turning lights and check that state right turning information ET309 and
state left turning information ET310 are ACTIVE, if not, refer to the corresponding chapter of
these states.
Check the condition of connector P1 with 15 pins of Cockpit Central Unit
Replace it if necessary.
Ensure continuity of connections :
UC H connector P1 pin A9 left turning lamp
UC H connector P1 pin A8 right turning lamp
Fix if necessary.
Check the system operation
AFTER REPAIRING
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 29
Diagnostic – Damage location algorithm
RECOMMENDATIONSDo not consult these information but before a complete
checking by means of the CL IP tester.
Check the bulbs
Check the condition of parking lights fuse F14 (7.5A)
Replace it if necessary.
Act upon the parking lights control and check that state parking lights information ET257 is
ACTIVE , if not, refer to the corresponding chapter of these state.
Check the continuity of the connection:
Parking lights fuse F14 (7.5A) rear and front parking lights
Fix if necessary.
ALP 3Parki ng lights not working
Check the system operation
AFTER REPAIRING
vnx.su