light DACIA SOLENZA 2004 Manual PDF
[x] Cancel search | Manufacturer: DACIA, Model Year: 2004, Model line: SOLENZA, Model: DACIA SOLENZA 2004Pages: 891, PDF Size: 14.84 MB
Page 534 of 891

81
INSIDE AND REAR LIGHTING
81 - 1
REAR LAMPS
RE AR LAMP REPLACEMENT
DISMOUNTIN G
Disconnect the battery (-) plug.
Disconnect the rear lamp connector .
Inside trunk, dismount the screw with triangle head ( A).
Extract the rear lamp towards outside.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, positioning correctly the rear lamp in
its seat. Check the bulbs connections and operation.
Rear right lamp Rear left lamp
Rear right lamp connector Rear left lamp connector
Pin Denomination Pin Denomination
1+ Right stop lamp 1 Fog parking lamp supply
2+ Right parking lamp 2 Left turning lamp supply
3Free 3 Free
4 Mass 4 Mass
5 Right turning lamp supply 5 + Left stop lamp
6 Revere driving lamp supply 6 + Left parking lamp
Inside and rear lighting
A
6
1 B
B
B
B 6
1
vnx.su
Page 535 of 891

INSIDE AND REAR LIGHTING
81
81 - 2
R
EPLACEMENT OF REAR TURNING,
P ARK ING, FOG, REVERSE DRIVING,
STOP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the rear lamp connector
Dismount the screw with triangle head
Extract the rear lamp towards outside
Di smount the two attachment screws (B) of
the bulbs support on the lamp glass.
Dismount the worn bulb.
REMOU NT I NG
Perform the dismounting opera tions i n the
reverse order, checking the condition of the
s ealing ga sket between the lamp glass and the
bulbs support: if this one is not good, replace it.
Check the bulbs operation and connections.
REPLACEMENT OF LICENSE PLATE LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the license plate lamp connector.
Extract the license plate lamp holder.
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting opera tions i n the
reverse order. Check the bulb operation.
REPLACEMENT OF ADDITIONAL
STOP LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the TORX 20 attachment screw
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Inside and rear lighting
Disconnec t t he addit ional st op l amp
connector. Detach t he two side clips and extra ct the
reflector-glass assembly from the lamp body.
Detach carefully from clips the lamp glass,
by means of a straight screwdriver. Replace the worn bulb.
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and
operation.
REPLACEMENT OF LICENSE PLATE LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disco nnect the license plate lamp
connector. Detach from clips the license plate lamp.
REMOUNTING
Pe rform t he di smounting opera tions i n t he
reverse order. Check the bulb operation.
R EPLACEMENT OF ADDITIONAL
STOP LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the attachment screw TORX 20
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Disconnec t t he addit ional st op l amp
connector.
R EMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and operation.
vnx.su
Page 536 of 891

81
INSIDE AND REAR LIGHTING
81 - 3
R
EPLACEMENT OF THE SIDE REAR LAMP
DISMOUNTIN G
Dismount the attachment screws of the wing protector.
Dismount the wing protector
Disconnect the connector
Detach from clips the side rear lamp.
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Inside and rear lighting
vnx.su
Page 537 of 891

INSIDE AND REAR LIGHTING
81
81 - 4
The ceiling lamp is central located, between
the two sun visors.
The ceiling lamp has 3 operating positions
subject to ceiling lamp glass position (4):
- position 1 : ceiling lamp off
- position 2 delayed ceiling lighting; this
will light for 15 seconds after driver’s front door
closing or after the command of unlocking the
doors with the RF remote control . This delay
turns out in the moment of setting the contact.
- position 3 : c eiling lamp pe rmanently
lighting.
DISMOUNTIN G
Disconnect the battery ( -) terminal.
Detach from clips the assemb ly from the lamp
support by means of a little screwdriver acting in
front of the slot (A). Disconnect the connector
Remove the roof lining around ceiling lamp
support. Detach from clips the ceiling lamp support.
REMOU NT I NG
Perform the dismounting operations in t he
reverse order. Check the ceiling lamp operation. Ceiling lamp connector
Pin Denomination
1 Mass
2+
protected battery – exit fuse F02
3 Ceiling lamp control
REPLACEMENT OF CEILING LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal;
Detach care fully the lamp glass using a
small screwdriver acting in point ( B).
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting operations in the
reverse orde r, using for lamp glass clips
attachment, a small screwdriver positioned in
point (B).
Check the ceiling lamp operation.
Ceiling lamp
A
B
3 1
vnx.su
Page 538 of 891

81
INSIDE AND REAR LIGHTING
81 - 5
Bulbs
BULBS
Headlamps High/low beam lights Bulb H4, 12V-60/55W Parking lights Bulb W5W, 12 V-5W
Front turning lamp Bulb PY21W, 12V-21W (colored)
F og projectors Halogen bulb H11, 12V-55W
Rear Parking, stop lights Bulb AB1, 12V-21/5W
lamps Turning lights Bulb PY21W, 12V-21W Rear fog lamp and reverse driving Bulb P21W 12V/21W
Rear side signalin g lamps Bulb WY5W 12V-5W
Ceiling lamp Bulb C5W, 12V-5W
License plate lamp Bulb W 5W, 12V-5W
Additional STOP lamp Bulb C21W, 12V/21W Sv8,5
Instrument panel Bulb12V, 2W (brown holder)
Bulb 12V, 1,2W (black holder)
Climate control panel Bulb 12V, 1,2 W
(black holder
vnx.su
Page 539 of 891

INSIDE AND REAR LIGHTING
81
81 - 6
Lamps failures diagnostic
FOG LAMP NOT WORKING
Ye s
Ye s
Ye s Ye s
No
No No
No
Replace fuse F06
Replace the STOP contact
Replace fuse F19
Replace under steering
wheel control. Check fuse F06 from cockpit fuse box.
Is it worn?
Check the continuity and resistance against vehicle mass between:
- exit fuse F06 pin2 reverse driving contact c onnector
- pin1 reverse driving contact connector pin 6 right rear lam
connector
- pin 4 right rear l amp connector vehicle m ass
Ar e they good?
Defective wiring. Fix it.
Check fuse F19 from cockpit fuse box. Is
it worn? Check the continuity and
resistance against vehicle mass between:
- battery pin B2 light control lever and signaling,
- pin A3 inlet fuse F19,
- exit fuse F19 pi n 1 left rear lamp connector,
- pin 4 left rear l amp connector vehicle m ass.
Ar e they good?
Defective wiring. Fix it.
REAR DRIVI NG LAMP NOT WO RKING
vnx.su
Page 540 of 891

81
INSIDE AND REAR LIGHTING
81 - 7
Lamps failures diagnostic
STOP LAMPS NOT WORKING
Check fuse F04 from cockpit fuse box.Is it good?
Replace fuse F04Yes
Yes
No No
No
Ye s
Replace t he Stop contact
The stop contact wire supply is broken or disconnected. Fix it. Bridge the Stop contact terminals.
Are the lamps working?
Is the Stop contact supplied ?
The stop contact wire supply is broken or disconnected. Fix it.
vnx.su
Page 541 of 891

INSIDE AND REAR LIGHTING
81
81 - 8
DISMOUNTING
Disconnect the (-) plug of the battery.
Pull the seat ( 1) of the access flap ( 2) to the fuse box located in the cockpit, at the l eft end of
the dashboard. Carefully remove flap ( 2).
Dismount the attaching screws ( 3) of the fuse box on the driving post crossbeam and detach
it from clips (4)
R EMOU NT I NG
Attach in clips ( 4) the fuse box on the driving post crossbeam and mount the screws ( 3).
Carefully mount, the access flap ( 2) to the fuse box.
Connect the battery (-) terminal.
Perform functional tests, noticing the correct operation of all consumers supplied by means
of the cockpit fuse box.
OBSERVATION:
For vehicle equipped with programmable radio-tape player and electronic c lock, af-
ter battery reconnecting, the radio code must be introduced and the clock re-programmed.
If COBRA 3800 or COBRA 3900 alarms have been mounted on the vehicle, in the
fuse box, may be found fuses F29 with value 15 A (mounted in seat (5)) and F 30 with
value 5A (mounted in seat (6)).
Cockpit fuse box
2
1
4
4 3
35 6
vnx.su
Page 542 of 891

81
INSIDE AND REAR LIGHTING
81 - 9
Cockpit fuse box
The fuses are protecting the following electric circuits:
Fuse Symbol Fu se Protected circuit
number type
F01 Free
F02 PLAF 15 A Instrument panel, cockpit UCE(ceiling lamp operation, radio
F03 20 ACockpit UCE, air conditioning climate control panel *
F04 15 ACockpit UCE, diagnostic socket, airbag UCE, anti-starting
bus h ing
F05
UC E10 A UCE injection , petrol pump relay/ignition coil, instrument panel
INJECTION
F06 10 AWindscreen wiper-washer switch (windscreen washing pump
operation), reverse driving switch, STOP switch, air
conditioning climate control panel*
F07 20 AWindscreen wiper-washer switch, UCE cockpit (windscreen
wiper timer operation), windscree n wiper motor (sto ppi ng at fix point).
F08 7,5 ALeft meeting lights, instrument panel (indicator)
F09 7,5 ARi ght meeting lights
F10 7,5 ALeft road lights, instrument panel (indicator)
F11 7,5 ARight road lights
F12 15 AAcoustic warning
F13 25 AUCE cockpit (turning lights and hazard), diagnostic socket.
F14 7,5 AFront/rear left parking lights, lighting: switches, climate control
panel, instrument panel, lighter, radio.
F15 7,5 AFront/rear right parking lights
F16 15 ALighter, radio
F17 30 AClimate control blower
F19 7,5 AFog lamp, instrument panel (indicator)
F20 25 ARear window defrosting
UC E
F21 INJECTION 5 AUCE injection
F23 30 ARight/left electric window regulator switch
F26 30 A Air conditioning climate control blower*
F28 20 AFog projectors
* for vehicles equipped with air conditioning
vnx.su
Page 543 of 891

INSIDE AND REAR LIGHTING
81
81 - 10
DE SCR IPTION OF THE OPERATION
Dismount the battery (-) terminal;
Dismount the access flap to the cockpit fuse box;
Dismount the attachment screw of the UCE decoder and relays assembly.
Lift from its attachment place and remove UCE decoder and relays assembly.
UCE decoder protection
1 2
Carefully insert UCE decoder-relays assembly in the protector ( 1) so that protector is not
damaged.
Attach the protector to the front wiring by means of an attachment clip (2).
Mount the UCE decoder – relays assembly in t he attachment place.
M ount the attachment screw of the UCE decoder and relays assembly.
M ount the access flap of the cockpit fuse box.
Connect the battery (-) terminal.
AT T E N T I O N !
At any intervention implying dismounting of the UCE decoder-relays assembly, the
protector and t he attachment clip are to be replaced.
vnx.su