lock DACIA SOLENZA 2004 Repair Manual

88
WIRING
88 - 17
Diagnostic – Failure interpretation
DF003
PRESENT
CONTINUATION
CC.1 – CC.0
RECOMMENDATIONS Nothing to notice
Block the computer by means of the CLIP t ester (see “Blocking UCE a irbag”)
Set the contact off and dismount the two attachment screws of the airbag on the steering wheel.
Check the condition of the airbag releasing lines.
Only CLIP tester is to be used for measuring the isolation in point C2 of the airbag circuit (using
cable A of the 30 pins adapter).
If value resulted is not correct, replace the control under steering wheel.
Reconnect the rotating contact of the control under steering wheel, disconnect the computer
connector and connect in its place the 30 pins adapter B40.
Only CLIP tester is to be used for measuring the resistance of the driver’s airbag releasing line,
using cable A of the 30 pins adapter.
If value resulted is not correct, check the 30 pins connector (pins 10 and 11) and replace the
front wiring if necessary. AFT ER Connect UCE airbag and driver’s airbag then set the contact on.
INT ERVENT ION Erase by means of the CLIP tester the failures memorized by UCE
airbag, then turn the contact off.
Perform again a checking by means of the CLIP tester; in case of failure
absence, unblock the computer.
Destroy the airbag pillow, if you are replacing it (see “Destroying
procedure”)
vnx.su

88
WIRING
88 - 18
D
F010 AIRBAG DEFECTIVE INDICATOR CIRCUIT
PRESENT CC.1 : short-circuit at + 12 volts
CC.0 : open circuit or short-circuit a t mass
RECOMMENDATIONSCharacteristics: the measurement of the airbag releasing lines is to
be performed only by means of the CLIP tester.
Use 30 pins adapter B40 for the intervention at the l evel of the
computer connector (the gray connector of the 30 pins adapter).
CC.1
RECOMMENDATIONS Nothing to notice
Block the computer by means of the CLIP tester (see “ Blocking UCE airbag”)
Check the condition the airbag indicator from instrument panel.
Check insulation against 12 volts between: airbag indicator pin 7 of the 30 pins connector
C0.0
RECOMMENDATIONSNothing to notice
Indicator off after setting the contact on
Block the airbag computer by means of the CLIP tester (see “ Blocking UCE airbag”)
Check the condition the airbag indicator from instrument panel.
Check continuity between: airbag indicator pin 7 of the 30 pins connector
Check the supply with 12 volts of the airbag indicator.
If the performed checking did not evidence any failure, disconnect UCE airbag and connect
instead of it t he 30 pins adapter. Check only by means of the CLIP tester the operation of the
airbag indicator from instrument panel, using the gray connector of the adapter B40.
If the airbag indicator lighting is possible by means of the CLIP tester, replace UCE airbag (see
chapter <> for this intervention).
If airbag indicator lighting is not possible, perform again the checking previously described.
Indicator on after setti ng the contact on
Block the airbag computer by means of the CLIP tester (see “ Blocking UCE airbag”)
Disconnect UCE airbag connector and check the presence of the 5 pegs that are ensuring shunt
unblocking of the 30 pins connector of UCE airbag.
Ensure insulation against mass of the route: airbag indicator pin 7 of 30 pins connector
AFT ER Erase the failures memorized by UCE airbag, then turn the contact off.
INT ERVENT ION Perform again a checking by means of the CLIP tester; in case of failure
Diagnostic – Failure interpretation
vnx.su

88
WIRING
88 - 19
absence, unblock the computer.
D F016 COMPUTER CONFIGURATION
PRESENT
RECOMMENDATIONSCharacteristics: nothing to notice.
Diagnostic – Failure interpretation
The presence of this failure is correspo nding to an incoherence between the computer configuration
and the vehicle equipping, detected by the CLIP tester.
Modify the UCE airbag configuration by means of the CLIP tester, using the control “System
elements configuration”. AFT ER Erase the failures memorized by UCE airbag then turn the contact off.
INT ERVENT ION Perform again a checking by means of the CLIP tester; and in case of
vnx.su

88
WIRING
88 - 20
failure absence, unblock the computer.
DF034 BLOCKED COMPUTER
PRESENT 1. DEF : blocked further to a shock
2. DEF : blocked by m eans of CL IP t ester.
RECOMMENDATIONS Characteristics : nothing to notice
This failure is allowing visualization of the blocking state of the airbag computer.
When present, all releasing lines are inhibited, driver’s airbag releasing being not possible.
1. DEFRECOMMENDATIONS Nothing to notice
This failure is present after airbag releasing.
It is obligatory UCE airbag replacement and of the airbag pillow after shock producing
2. DEF RECOMMENDATIONS Nothing to notice
This failure is present in the following situation s:
- UCE airbag is new ( t his one is delivered blocked)
-I n case of an intervention on the vehicle, the computer blocking control is used, by
means of CLIP tester.
Unblocking : Perform again a checking by means of CLIP tester ; in case of failure absence,
unblock the computer.
Erase the memorized failure then turn t he contact off. AFTER Erase the failures memorized by UCE airbag, then turn the contact off.
IN TERVENTION Perform again a checking by means of the CLIP tester; in case of
failure absence, unblock the computer.
Diagnostic – Failure interpretation
vnx.su

88
WIRING
88 - 22
Diagnostic – Help
UCE A IRB AG REPL ACEMENT
New airbag computer are delivered in blocked condition in order to avoid all risks of
undesirable releasing (all releasing lines are inhibited).
This “blocked” mode is noticed by the airbag indicator lighting from the instrument panel
when setting the contact on. In order to replace t he UCE airbag, proceed as follows:
- set the c ontact off,
- dismount the central console tunnel,
- disconnect the UCE airbag connector,
- dismount the UCE airbag attachment screws,
- mount the new UCE airbag, the arrow from UCE a irbag being oriented towards front
of the vehicle, - reconnect UCE airbag connector,
- check t he system by means of the CLIP tester,
- modify if necessary the airbag computer configuration using the control “Configuration”,
- unblock the computer only in case of a failure absence, declared by the CLIP t ester.
DESIGNATION OF THE 30 WAYS UCE AIRBAG PLUGS
1. Free
2. Free
3. Free
4. Free
5. Supply + after contact
6. M a ss
7. Airbag failure indicator
8. Free
9. K diagnostic line
10. Driver’s frontal airbag (+) 11 .D river’s frontal airbag (-).
12. Free
13. Free
14. Free
15. Free 16. Free
17. Free
18. Free
19. Free
20. M a ss
21. Free
22. Free
23. L diagnostic line.
24. Free
25. Free
26. Free
27. Free
28. Free
29. Free
30. Not in use
vnx.su

89
ELECTRIC DIAGRAMS
89 - 2
The fuse box from the engine compartment is presented in Chapter 9, that contains information
about its location on the vehicle and the functional purpose of the relays and fuse placed on it.
The functional codes of the wires are detailed explained in Chapter 12. FUNCTIONAL DIAGRAMS INTERPRETATION
The functional diagram information included in Chapter 7 are to be i nterpreted taking i nto
consideration the explanation referring to the following example:
1= vehicle class
2= manufacturing year
3= functional electric diagram denomination
4= equipment differentiation criteria for identifying the functional electric diagram ˙
5= electric connector colour ˝
6= connector graphical representation
7= electric component index number
8= number of the fuse box on which the relay or safety fuse is m ounted
9= safety fuse identification on fuse box
10 = safety fuse value
11 = identification of wiring joints
12 = electric mass identification
13 = electric connection colour between wiring ˝
14 = electric connection identification
15 = electric connection graphical representation
16 = symbol, pages containing functional diagrams
17 = wire function code
18 = wire colour ˝
19 = functional diagram number
OBSERVATION:
1. The area ( 4) specifies the differentiating elements serving to the various functional diagrams
identification, considering the following symbols:
ABCO01 = driver’s airbag
CA = climate maintenance with air conditioning
CHAUFO = climate maintenance without air conditioning
CPE = Electric locking/unlock ing doors control
DA = assisted power steering
E0, E1, E2 = levels of equipment
LV E = front windows electric control
___ ___________________________________________________________________________
General
vnx.su

89
ELECTRIC DIAGRAMS
89 - 6
Functional diagrams list
DOORS CENTRAL LOCKING
ANTI-STARTING
SPEED LIMIT INDICATOR
ELECTRIC LIGHTER
CLIMATE CONTROL
CLIMATE CONTROL AND AIR CONDITION
CEILING LAMP
FRO NT WINDOWS ELECTRIC CONTROL
RADIO
STARTING CIRCUIT
E NGINE COOLING FAN
ELECTRONIC INJECTION
CHARGING CIRCUIT
REAR WIRING MASS
FRONT WIRING/ DASHBOARD MASS
BATTERY/CARRIAGE BODY MASS
FOG PROJECTORS WIRING MASS
HATCHB ACK WIRI NG MASS
E NGINE WIRING MASS
COCKPIT FUSE BOX
E NGINE FUSE BOX AND RELAY
HANDBRAKE INDICATOR / BRAKING SYSTEM FAILURE
FUEL LEVER INDICATOR
OIL PRESS URE INDICATOR
DIAGNOSTIC SOCKET
DASHB OAR D
ALER T TEMPERATU RE INDICATOR FOR COOLING FLUID
WA TER TEMPERATURE COOLING FLUID INDICATOR
SPEED INDICATOR
DRIVER’S AIRBAG
DRIVER SAFETY BELTS INDICATOR
ACOUSTIC WAR NING
REAR WINDOW DEFROSTING
ELECT RIC D IAGRAM S DE NOM INATION DI AGRAM NUM B E R
1
2
3
4
5
6
7
8
9-10
11
12-13
14-15-16-17-18-19-20-21
22
23-24
25-26-27-28-29-30-31-32-
33-34-35-36
37
38
39
40-41-42-43
44-45-46-47-48-49-50-51-
52-53-54-55-56-57-58-59
60-61-62-63
64
65-66
67
68-69
70-71-72-73-74
75
76
77-78
79
80
81
82
vnx.su

89
ELECTRIC DIAGRAMS
89 - 11
Electric components location on the vehicle
In ject or 1
Inject or 2
Inject or 3
Inje ctor 4
Atmospheric pressure sensor
Detonation sensor
Starter
In jection air temperature sensor
Valve potentiometer
Upstream oxygen sensor
Step-by step engine
Alternator
Ignition c oil
Canister purging valve
AC pressure sensor (pressure controller)
Pressure controller DA
AC compressor clutch
Upstream oxygen sensor
Cooling motor fan and AC
Cooling engine fan resistance for AC
Oil pressure contact
Injec tion computer
RPM sensor
In jection water temperature sensor
Reverse driving contact
Fuse box and engine relays
Vehicle speed transducer
I CP brake system
Chock sensor
Windscreen wiper motor
Windscreen washing motor
Speed limit ind icator
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32Turning lights relay
Front door contact
Windscreen wiper timer
Left fron t door actuator
Le ft elec tric window actuator
Left fr ont door loud speaker
Cockpit fuse box
UCE d ecoder
FLASH relay
Rear window defrosting switch
Anti-starting bushing
STOP contact
Radio
Doors locking switch
Li ghter
Hazard switch
Climate control panel
Electr ic right window switch
Electr ic left window switch
UCE airbag
Diagnostic socket
Handbrake contact
Safety belt contact
Driver’s airbag
Right front door loud speaker
Electr ic right window actuator
Right front door actuator
Right rear door actuator
Right rear loud speaker
STOP-S3 lamp
Fuel level transmitter and electric pump
Left rear door loud speaker
Left r ear door actuator
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
No. Denomination
No.Denomination
vnx.su

89
ELECTRIC DIAGRAMS
89 - 18
Index in connectors and couplings
Denomination
ELECTRIC LIGHTER
ALTER NATOR
ALTERNATOR EXCITATION
ANT I-THEFT MECHANISM
ACOUSTIC WAR NING
(+) BATTERY (engine wiring)
(+) BATTERY (front wiring-dashboard)
WINDSCREEN WIPER TIMER
UCE INJECTION( for vehicles without AC)
UCE INJECTION( for vehicles with AC)
LOCKIN G DOORS SWITCH
CLIMATE CONTROL PANEL
HAZARD SWITCH
REAR WINDOW DEFROSTING SWITCH
ELECTRIC RIGH T WINDOW SWITCH
ELECTRIC LEFT WINDOW SWITCH
TURNING LIGHTS RELAY
RIGHT REAR DOOR ACTUATOR
LEFT FRONT DOOR ACTUATOR
LEFT FRONT DOOR ACTUATOR
RIGHT FRONT DOOR ACTUATOR
WINDSCREEN WIPER-WASHING SWITCH
D ETONATION SENSOR
ATMOSPHERIC PRESSURE S ENSOR
RPM SENSOR
REVERSE DRIVING CONTACT
HANDBRAKE C ONTAC T
STOP CONTACT
STARTER
STARTER EXCITATION
AC COMPRESSOR C LUTCH
RIGHT REAR LAMP
LEFT REAR LAMP
RIGHT FOG PROJECTOR
LEFT FOG PROJECTOR
LEFT FRONT DOOR CONTACT
RIGHT FRONT PARKING LAMP
LEFT FRONT PARKING LAMP
E NGINE COOLING FAN ( for vehicles without AC)
RIGHT REAR LOUD SPEAKER
LEFT REAR LOUD SPEAKER
RIGHT FRONT DOOR LOUD SPEAKER
LEFT FRONT DOOR LOUD SPEAKER
INJECT OR 1
INJECT OR 2
INJECT OR 3No.con.
101
103 HA
103 HB
104
105
107
107AA
113
120
120
123
124
125
128
132
133
137
138
139
140
141
145
146
147
149
155
156
160
163 GA
163 AB
171
172
173
176
177
180
184
185
188
189
190
191
192
193
194
195 P
age
89-139
89-113
89-113
89-139
89-140
89-114
89-140
89-141
89-115
89-117
89-141
89-142
89-143
89-143
89-144
89-144
89-145
89-172
89-172
89-146
89-146
89-147
89-120
89-120
89-121
89-121
89-173
89-147
89-122
89-122
89-123
89-173
89-174
89-177
89-177
89-148
89-148
89-148
89-123
89-174
89-175
89-149
89-149
89-124
89-124
89-125
vnx.su

89
ELECTRIC DIAGRAMS
89 - 49
WINDSCREEN WIPER TIMERDOORS LOCKING SWITCH
10 .35 20D CONTROL + ELECTRIC LOCKING DOORS>U.C.E. DECODE R
20.35L PG + PARKING LIGHTS>OUTL ET FUSE F14
30.5MK MAS S
40.5MK MAS S
50 .35 20C CONTROL + ELECTRIC UNLOCKING DOORS>U.C.E. DECODER
PositionSection Destination
Position Section Destination
10.6MKM
ASS
20 .35 16A CONTROL + WINDSCREEN WIPER PUM P
30 .6 14D WINDSCREEN WIPER TIMER LOW SPEED CONTROL
40 .6 14C CONTROL + WIPER FIX POINT STOPPING
51 .0 AP7 + AFTER PROTECTED CONT ACT WINDSCREEN WIPER
90 .35 14E CONTROL + WINDSCREEN WIPER TIMER
NO
113
N X
5 4 3
AP 7 14C 14D
6 1 9
M K 14E
7 2 8
16A
V
VI X X
FRONT WIRING – DASHBOARDX412
03
Wires functions in connectors and couplings
vnx.su