bulb DACIA SOLENZA 2004 User Guide
[x] Cancel search | Manufacturer: DACIA, Model Year: 2004, Model line: SOLENZA, Model: DACIA SOLENZA 2004Pages: 891, PDF Size: 14.84 MB
Page 538 of 891

81
INSIDE AND REAR LIGHTING
81 - 5
Bulbs
BULBS
Headlamps High/low beam lights Bulb H4, 12V-60/55W Parking lights Bulb W5W, 12 V-5W
Front turning lamp Bulb PY21W, 12V-21W (colored)
F og projectors Halogen bulb H11, 12V-55W
Rear Parking, stop lights Bulb AB1, 12V-21/5W
lamps Turning lights Bulb PY21W, 12V-21W Rear fog lamp and reverse driving Bulb P21W 12V/21W
Rear side signalin g lamps Bulb WY5W 12V-5W
Ceiling lamp Bulb C5W, 12V-5W
License plate lamp Bulb W 5W, 12V-5W
Additional STOP lamp Bulb C21W, 12V/21W Sv8,5
Instrument panel Bulb12V, 2W (brown holder)
Bulb 12V, 1,2W (black holder)
Climate control panel Bulb 12V, 1,2 W
(black holder
vnx.su
Page 578 of 891

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 35
Diag nostic
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
A LP9. THE CEILING LAMP DOES NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS OR IT REMAINS PERMANENTLY TURNED ON
RECOMMENDATION Check the absence of failures with the CLIP tester. If there are memorised failures, fix them first.
Check if t he doors are locked? The ceiling lamp was in
the position “permanently
lighting”? Normal
operation.Yes Yes
Unlock the doors with the RF remote control.
The ceiling is in the position “ceiling delayed
lighting ”.
Has the ceiling lamp turned on?
Check the isolation of the wiring related
to the mass on the line pinA1.
decoder pin 3 c eiling lamp.
After 15 seconds, the ceiling lamp will
turn off.
Normal operation.
Wa s the E.C.U. decoder confi gured “With
ceiling delayed lamp”?Configure the E.C.U. decoder with
the CLIP tester.
Check the continuity on the line
E.C.U. decoder pin A1 pin 3 ceiling
lamp.
Is the line good?Repair .
Check the ceiling lamp bulb.
No
No
No
Yes
Yes Yes
No
vnx.su
Page 614 of 891

INSTRUMENT PANEL
83
83 - 8
Diagnostic – damages interpretation
Check the oil pressure.
Pr essure is correct?
Replace the oil pressure transmitter. There is a failure in the oil circuit.
Fix it.
OIL P RESSURE INDICATOR IS NOT ON WHEN CONTACT SET ON
Place the wire from the oil pressure
transmitter to the mass Is the indicator on ?
Replace the oil
pressure transmitter Replace the bulb.
Wa r
ning indicator bulb is
worn?
Check the bulb supply wiring and fix it.
FUEL LEVEL INDICATOR SHOWING ALWAYS FULL
Replace the fuel level transmitter.
Replace the instrument panel. Disconnect the connection wire t o the probe.
Is the fuel level indicator showing zero ?
Resistance against the vehicle mass of the B1 pin
of the fuel level transmitter connector is zero?
Defective wiring. Fix it.Ye s
No
Ye s N o Ye sNo
Ye s No No
Ye s
OIL PRESSURE INDICATOR STILL ON
AFTER ENGINE STARTING
vnx.su
Page 626 of 891

84
STEERING - CONN ECTOR
84 - 11
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the upper part dashboard.
Disconnect connectors ( 1), (2) and (3). Mark identification of their mounting position.
Holding with one hand the fix part ( 4) dismount the lighter attachment clamp ( 5) on the lower
part dashboard. Extract the lighter fix body (part).
REMOU NT I NG
Position the lighter fix body in the dashboard lower part. Holding with one hand the fix body,
mount the lighter attachmen t clamp. The required tightening moment is 1.5 Nm applied to the fix
body (4). Connect the lighter connectors, observing their mounting position existent prior to dismount-
ing. Mount the upper part dashboard.
Reconnect the battery (-) terminal.
Check the operation of the electric lighter.
REMARK:
In order to replace the bulb, dismount the lighter, dismount the bulb holder (6) from
the clamp (5) and replace the bulb.
Connectors
Connector Denomination 1 Mass
2 Supply + after contact
3 Supply + parking
Electric lighter
vnx.su
Page 665 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 25
Diagnostic – States interpretation
ET257PARKING LIGHTS INFORMATION
RECOMMENDATIONS Check that no failure is present or memorized. Act upon the parking lights control.
State must be ACTIVE, and the parking lights on
Check the bulbs.
Check parking lights fuse F14 (7.5 A)
Replace it if necessary
Check connection and c ondition of UCH connector EH1 40 pins .
Replace the connector if necessary
Ensure continuity and insulation of the connection:
pin A15 connector EH1 40 pin sfuse box, parking
lights fuse (7.5A)
Fix if necessary.
ET257
INACTIV
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su
Page 668 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 28
Diagnostic – Damage location algorithm
ALP 2Turning lights not working
RECOMMENDATIONS Do not consult these information but before a complete
checking by means of the CLIP tester.
Check the bulbs
Check the condition of fuse F13 (25A) and replace it i f necessary.
Pu sh the hazard switch and check that state <
ACTIVE ; if not, refer to chapter dealing with this state.
Act upon the right or left turning lights and check that state right turning information ET309 and
state left turning information ET310 are ACTIVE, if not, refer to the corresponding chapter of
these states.
Check the condition of connector P1 with 15 pins of Cockpit Central Unit
Replace it if necessary.
Ensure continuity of connections :
UC H connector P1 pin A9 left turning lamp
UC H connector P1 pin A8 right turning lamp
Fix if necessary.
Check the system operation
AFTER REPAIRING
vnx.su
Page 669 of 891

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 29
Diagnostic – Damage location algorithm
RECOMMENDATIONSDo not consult these information but before a complete
checking by means of the CL IP tester.
Check the bulbs
Check the condition of parking lights fuse F14 (7.5A)
Replace it if necessary.
Act upon the parking lights control and check that state parking lights information ET257 is
ACTIVE , if not, refer to the corresponding chapter of these state.
Check the continuity of the connection:
Parking lights fuse F14 (7.5A) rear and front parking lights
Fix if necessary.
ALP 3Parki ng lights not working
Check the system operation
AFTER REPAIRING
vnx.su