key DACIA SOLENZA 2004 User Guide

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 4
REMARK :
The vehic les equipped with this anti starti ng system, have a type of decoder, and those
provided also with R F remote control for l ocking/ unlocking doors have another ty pe of
decoder.
Th e identification of the two types of E.C.U. decoder is realised by the inscriptions on the
labels as follows: - code P8200032783H and the in scri ption TRANS-PLAF for the vehicle s w ithout RF
remote control; - code P8200032776H and the inscr iption TRF-TRANS-CAR for the vehicles with RF
remote control. ANTI STARTING INDI CATOR
It is located on the instrument panel (position A) and has the following functions:
- signalising the activation of the anti starting system;
- signalising the case of non identifying the key head;
- signalling the entrance in the operation mode “resynchronisation” of the remote controls, RF
with E.C.U. decoder, for the vehicles which use the RF remote control.
When the contact is off and the anti starting system is activated, without any existing failure, the
an ti starting indicator must blink slowly (a blink per second).
After setting the contact on, the anti starting indicator must light for 3 seconds and then turn off.
If a fter setting the contact on, the anti starting system doesn’t work properly, then the anti
starting indicator will blink rapidly (two blinks per second). Th
e ceiling delayed lighting is activated subject to the position of the light glass ( 1):
- position A the ceiling is lighting permanently;
- position B de layed ceiling lighting; this will light for 15 seconds after driver’s front door closing
or after the command of unlocking the doors with the RF remote control. This delay turns out in the
mo ment of setting the contact;
- po sition C ceiling light off.
General
AA
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 5
After ordering a new key head based on the alphanumeric code mentioned on the invoice,
dismount the old key head and remove the metal insertion (mechanical part), then introduce the old
meta l insertion in the new key head according to the previously mentioned procedure. In case the
key head is provided with RF remote control for blocking/ unlocking the doors, after its replacement,
pe rfor m the synchronising procedure of the RF remote control with the decoder, subject to the
fo llowing cases:
- a fter the replacement of the RF key, perform the “Specific synchronised procedure” in order
to bring into phase the RF remote control with the decoder. - if both keys are replaced, perform the “Simple synchronised procedure” for the first RF key
and the “Specific synchronised procedure” for the second one RF key.
If a key was lost, a new key head and a metal insertion are to be ordered.
One key head replacement
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 6
All new decoders, are not coded. After mounting on the vehicle, it is necessary the memorisation
of the key head code by the decoder in order to be operational. If only the decoder is replaced, no
intervention is necessary to the injection computer, which will keep the old anti starting code. When
the vehicle is provided with RF remote control for blocking/unlocking the doors, the performing of
the resynchronisation of the keys with the decoder is imposed, after its mounting. If further to the
di ag nostic of the anti starting system, using the CLIP tester, the replacement of the decoder is
imposed, proceed as follows:
DISMOUNTIN G
- disconnect the (-) terminal of the battery;
- d ismount the ECU decoder-relays assembly;
- ro tate the ECU decoder assembly, in order to have access at its rear connectors;
- d isconnect the front wiring connector from the E.C.U. decoder;
- deta ch ECU decoder from clips of the relays-ECU decoder support.
REMOU NT I NG
- attach in clips the new E.C.U. decoder in the support, connect the front wiring connector to
the ECU decoder, then attach the assembly on the driving post cross member in its place and
mo unt its attachment screw;
- remo unt carefully the access flap of the fuse box;
- reconnect the (-) term inal of the battery.
Proceed then to the insertion of the anti starting code using the contact key, then to its me morising
(va lidation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder replacement procedure and anti starting code memorising”. Check then the correct operation
of the anti starting system with both keys.
ATTENTION!
Once the decoder has memorised the key codes, this code cannot be erased or replaced
with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), then the “ Kit
replacement procedure” must be performed.
Dismounting - remounting E.C.U. decoder
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 8
The RF remote control has only the function of blocking/ unlocking the doors. The RF remote
c ontrol with evolutionary code can use only two keys as the decoder may manage only two different
e volutionary codes.
Th e key heads have an identification number formed by eight alphanumeric characters (letters
and fi gures), beginning with letter E. In case of loosing one key, a key head and a metal insertion
will be ordered, then the resynchronisation procedure of the RF remote control of the key with the
de coder from the vehicle must be performed.
If the ve hicle is provided with RF remote control key and this one has been replaced, then
pe rfor m the “ Simple synchronised procedure “. When the vehicle has both keys with RF remote
contro l, then perform the “Specific synchronised procedure “ after the replacement of the second
key.
REMA RK:
If only one key head is replaced, usually there is no need for resynchronisation of the
other RF remote control.
If both RF re mote controls are desynchronised, one procedure of resynchronisation will
be performed w ith each remote control: perform the “Simple synchronisation procedure for
the first R F r emote control” and the “Specific synchronisation procedure” for the second
RF remote control.
Check then, the operation of doors blocking/ unlocking with both RF r emote controls.
R.F. remote control for blocking/unlocking the doors
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 12
Procedures
A. E.C.U. DECODER REPLACEMENT PROCEDURE AND
ANTI STARTING CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
REMARK:
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT T E N T I ON!
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one. In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed.
Proceed as follows:
1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter socket)
of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select the type “B41”
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol, programming with 1 or 2 keys, ceiling delayed
light, the type of the doors’ blocking switch (CPE), etc.;
3. Return to the menu “COMPUTER TEST”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder is
new, you must find the following states:
18G FIRST CYCLE MEMORISING………………….......………… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………..……….. ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………….………ACTIVE
OBSERVAT ION:
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
b een already used, so it isn’t new and cannot memorise another anti starting code.
6. Access t he menu “COMMAND MODE” and then “CONFIGURATION”, where you
will c onfigure t he new E .C.U. decoder in the same way as the old one : petrol, 1 ke y, ceiling
delayed light, impulsion doors blocking switch, etc. selecting one by one these configurations,
which you’ll validate with “CLICK” on the blue button on right top of the screen.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 13
Procedures
1. Return to “COMPUTER TEST”
2. Set the contact on for 2 seconds in “ M” position, without start ing the engine. The anti
starting indicator will begin to blink rapidly.
3. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE ………………………………......…… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….…… PASSIVE
10. Take the c ontact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE LIST”, which now, must be like that: 18G FIRST CYCLE MEMORISING…………………………….....…ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………….……..PASSIVE
19D UNBLOCKED KEY PROGRAMMING …………………..…… PASSIVE
13. Set the contact i n “M” position for 2-3 seconds in order t o send the code t o the E.C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI STARTING” is “ ACTIVE”.
Perform the synchronisation of the TRF remote control with the decoder (with 1or 2 keys).
OBSERVAT ION:
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows:
- take the contact off; wait for 10 seconds, then the anti starting indicator will blink;
- in the menu, “COMMAND MODE” access “ ACTUATORS” then validate “ FORCED
PROTECTION MODE” launching the command from the blue button situated on the ri ght
topside of the screen. “COMMAND IN PROGRESS” will be displayed and then “FINISHED
COMMAND”; - in t he m enu “ STATE LIST” search for the state 10G ”ANTI START ING”, which
must be “ ACTIVE”; - set the contact on “M” position; the anti starting indicator will blink rapidly, and the
engine starting is impossible;
- remove the key from the contact and check then the engine starting with both keys, so
the procedure is finished.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 14
Procedures
RE M ARK:
For the RF remote control synchronisation, after the replacement of an E.C.U. decoder,
the sync hron is ation proced ure must be per formed taking i nto account the foll owing
situations : - fo r one RF remote control, perform the “ SIMPLE SYNCHRONISED
PROCED URE ”;
- for the second RF remote co ntrol per form the “SPE CI FI C SYNCHRONI SED
PROCED URE ”.
B. KIT REPLACEMENT PROCEDURE
(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder;
- memorising of the new anti starting code by the injection computer; it is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Inform by phone at ”Client Voice” (phone no 0248 500 000), the vehicle chassis series and
the key heads code, written on the vehicle invoice, in order to get the repairing code.
3. Connect the CLIP tester t o the diagnostic socket and to the battery (or to the lighter
s ocket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting it
off the vehicle, as follows:
- select vehicle type “B41”;
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configuration s : petrol/diesel, programming with 1 or 2 keys, ceiling delayed light,
the type of the doors’ blocking switch (CPE), etc.
4. Return to the menu “ANTI START ING”.
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STAT E LIST”; here you
must find the following states: 18G FIRST KEY MEMORISING……………………………........… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………………..... ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………………..... ACTIVE
REMARK:
If the state 19G and 19D are not “ACTIVE” this means the E.C.U. decoder isn’t a
ne w one and cannot memorise another anti starting code.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 15
Procedures
7. Set the contact i n “M” position with one of the ke ys (without start ing the engine), for
about 2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE ……………………………….....…..... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ………….........… ACTIVE
8. Set the contact with the second key (without starting t he engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;
9D RECEIVED KEY CODE ……………………………………..… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….....… PASSIVE
- case (b)- t he second key doe s not belong to t he vehicle or the first ke y was used once
again;
9D RECEIVED KEY CODE ……………………………………..… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………….....…… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In the menu “ COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE L IST”, which now must be as follows: 18G FIRST KEY MEMORISING…………………………….........… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………...……PASSIVE
19D UNBLOCKED KEY PROGRAMMING ………………...…...…PASSIVE
13. In the menu “COMMAND MODE” select “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”.
Return to the “STATE LIST “ and check t he state: 9GFORCED PROTECTION MODE ………………………....…… ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink ra pidly.
Check in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” a ccess “ACTUATORS”, then select the command
“ MANUAL CODE INTRODUCTION”. Type t he four fi gures of the repairi ng code, t hen
validate with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS”
w ill appear and then “FINISHED COMMAND”.
16. Set the contact off and then set again the contact on, without starting the engine, in order
to send the new anti starting code to the injection computer. The anti starting indicator will light
for 3 seconds, and then it will turn off.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su