lights DACIA SOLENZA 2004 User Guide

BATTERY - FRONT HEADLIGHTS
80
80 - 6
Bulbs
FOG PROJEC TOR B ULB RE PLACEMENT
DISMOUNTING
Suspend the vehicle on an elevator.
Disconnect the fog projector connector
Rotate the bulb holder ( F) an d extract it from its place.
REMOU NT I NG
Perform the dismounting operations in the reverse order, correctly positioning the bulb holder in
its place. Perform fog projector adjustment
NOTE :
Because the fog projector is equipped with a halogen bulb, do not touch the bulb glass
ba lloon directly by hand.
HEADLAMP BULB REPLACEMENT
DISMOUNTIN G
Disconnect the connector (2 ).
Remove the rubber protector ( 7). Mark its mounting position.
Release the atta chment clamp (8) and remove th e h e adlamp bulb
REMOU NT I NG
Perform the dismounting operations in the reverse order. Position correctly the rubber protector
( 7) observing the mounting position before dismounting. Perform headlamp adjustment.
NOTE :
Because the headlamp is equipped with a halogen bulb, do not touch the bulb glass balloon
d irectly by hand.
72 3 4
8
5
10
10
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 7
FRONT TURNING BULB REPLACEMENT
DISMOUNTIN
G
Disconnect the connector ( 3).
Rotate the holder ( 4) and remove it.
Remove the worn bulb from the holder
R EMOU NT I NG
Perform the dismounting operations in the reverse order, with t he checking of the correct
holder (4 ) positioning to avoid dust and humidity penetration in the headlamp assembly .
The turning lamps are using orange color bulb; when replacing the bulb, use the same bulb
type.
FRONT PARKING BULB REPLACEMENT
DISMOUNTIN G
Rotate the holder ( 5) and remove it.
Extract the worn bulb from the holder.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, with t he checking of the correct
holder (5 ) positioning to avoid dust and humidity penetration in the headlamp assembly .
Bulbs
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 8
HEADLAMP-FRONT LAMP ASSEMBLY SEALING
(getting fogged, it has condensation water or water penetration)
The condensation water is not affecting the lighting quality.
No No
No
No
No Ye s
Ye s
Ye s Ye s
Bulbs
Check the front part of the assembly: direct
a water jet towards the headlamp glass.
Is the water penetrating inside the headlamp?
Is wa ter penetrating inside the parking-turning
lamp?
Visually check the headlamp rear part; rubber
protecto r of the headlamp bulb is correctly
mounted?
The he adlamp adju stment corrector is well
mounted?
The headla mp bulb is correctly mounted?
The aera tion holes are clogged?
The hea dl amp is steamed out or it has
condensa tion water inside?
Visually check the rear part of the parking-
turning lamp; t he parking bulb holder is
correc tly mounted?
Th e turning bulb holder is correctly mounted?
Replace the headlamp.
Replace the parking-turning lamp.
Mount corr ectly the rubber protector of the
h eadlamp bu lb. If this is not good, replace it.
Mount corr ectly the headlamp adjustment
co rrector and its rubber protector. If protector
is not good, replace it.
Mount correc tly the headlamp bulb.
If possible, eliminate the clogging cause. If
no t possible, replace the headlamp.
Explain th e client that this fact is a natural
one, no t a damage and there is no headlamp
corro sion risk. The condensation water will
disappear when the headlamp will be lighted;
the disappearing time of the condensation
wat er is subject to the environmental
humidity .
Mount co rrectly the parking bulb holder. If
its gasket is not good, replace it.
Mount co rrectly the turning bulb holder. If
its gasket is not good, replace it.
REMARK : If the client is i nsisting, proceed to headlamp drying:
- blow with dry air, if possible;
- naturally dry the headlamp by turning on the headlamps for couple of minutes
till condensation water elimination or headlamp defoggi ng. No
No
No
No Ye s
Ye s
Ye s
Ye s
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 9
MEETING LIGHTS ADJUSTMENT (LOW BEAM)This is performed by acting upon the V screw
(vertically plane adjustment) or H (horizontally
p lane adjustment). By screwing, the lighting beam
is ”lowering” and by unscrewing is “ascending”. Check if the l ighted area is centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error of
1 cm is admissible. A lighting beam displaced towards left has
the aspect shown in (p icture a) and a lighting
beam displaced towards right has the aspect
shown in (picture b )
ROAD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to c oincide with the
adjustment pe rformed for low beam and with
the lighting beam distributed between the two
vertical lines on the panel
When checking the long beam, the lighting
center of t he ellipse, must be l ocated on t he
cross marking the screen center. If a m ajor de viation c ompared with t he low be am i s noticed, i t is re commended t he bul b
replacement, this one being in most of the cases, responsible for such defect.
Headlamps adjustment
H
V
figura a figura b
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 10
FOG P ROJECTORS ADJUSTMENT
The fog projectors adjustment is to be performed in the following conditions:
- the vehicle to be placed on a horizontal surface;
- the vehicle has not passengers inside the cockpit or weights in the trunk;
- the tires a re pressurized a t the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device –E) in front of an optical center
of a fog lamp. Switch on the fog projectors. Rotate the adjustment screw of the fog lamp (D), by means of
a scre wdriver ( A), so that a n adjustment of 2 % i s obtained and t he separation between t he
lighted area and the dark one from the adjustment device is l ocated under the marked line (G)
This adjustment is to be performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp;
Perform the fog projector adjustment;
Switch off the fog projectors.
H eadlamps adjustment
G
E
A
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount
the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector ( 1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut ( 3);
- detach from clips the he adlamp adjustment control cable ( 4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly .
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passin g hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOU NT I NG
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTIN G1
2
V
56 34
Replacement of the headlamps mechanic adjustment control
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
co mpartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamp s adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mo unt the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
-a ttach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) a n d t h en in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork ( 5) is in contact with support ( 6) so that fork
is remaining at max. 0.5 mm again st the support;
-block the headlamp adjustment cable by means of the nut ( 3);
-a ttach in clips the protector ( 2) o f t h e headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw ( V) mu st come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
± 10 mm between the right cable and the cylinder
no .1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery ( -) term inal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adju stment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “ 0” position
an d then in the desired condition.
REMA RK : The r equired tighteni ng moment of the attachment nut of th e headlamps
adju stment control on the dashboard: 2 Nm.
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 5
Bulbs
BULBS
Headlamps High/low beam lights Bulb H4, 12V-60/55W Parking lights Bulb W5W, 12 V-5W
Front turning lamp Bulb PY21W, 12V-21W (colored)
F og projectors Halogen bulb H11, 12V-55W
Rear Parking, stop lights Bulb AB1, 12V-21/5W
lamps Turning lights Bulb PY21W, 12V-21W Rear fog lamp and reverse driving Bulb P21W 12V/21W
Rear side signalin g lamps Bulb WY5W 12V-5W
Ceiling lamp Bulb C5W, 12V-5W
License plate lamp Bulb W 5W, 12V-5W
Additional STOP lamp Bulb C21W, 12V/21W Sv8,5
Instrument panel Bulb12V, 2W (brown holder)
Bulb 12V, 1,2W (black holder)
Climate control panel Bulb 12V, 1,2 W
(black holder
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 9
Cockpit fuse box
The fuses are protecting the following electric circuits:
Fuse Symbol Fu se Protected circuit
number type
F01 Free
F02 PLAF 15 A Instrument panel, cockpit UCE(ceiling lamp operation, radio
F03 20 ACockpit UCE, air conditioning climate control panel *
F04 15 ACockpit UCE, diagnostic socket, airbag UCE, anti-starting
bus h ing
F05
UC E10 A UCE injection , petrol pump relay/ignition coil, instrument panel
INJECTION
F06 10 AWindscreen wiper-washer switch (windscreen washing pump
operation), reverse driving switch, STOP switch, air
conditioning climate control panel*
F07 20 AWindscreen wiper-washer switch, UCE cockpit (windscreen
wiper timer operation), windscree n wiper motor (sto ppi ng at fix point).
F08 7,5 ALeft meeting lights, instrument panel (indicator)
F09 7,5 ARi ght meeting lights
F10 7,5 ALeft road lights, instrument panel (indicator)
F11 7,5 ARight road lights
F12 15 AAcoustic warning
F13 25 AUCE cockpit (turning lights and hazard), diagnostic socket.
F14 7,5 AFront/rear left parking lights, lighting: switches, climate control
panel, instrument panel, lighter, radio.
F15 7,5 AFront/rear right parking lights
F16 15 ALighter, radio
F17 30 AClimate control blower
F19 7,5 AFog lamp, instrument panel (indicator)
F20 25 ARear window defrosting
UC E
F21 INJECTION 5 AUCE injection
F23 30 ARight/left electric window regulator switch
F26 30 A Air conditioning climate control blower*
F28 20 AFog projectors
* for vehicles equipped with air conditioning
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 34
Diag nostic
ALP 8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester. If there are failures, fix them first.
Check if the synchronisation of the RF remote control and the E.C.U. decoder has been
performed.
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation
related to t he mass and the +12 V of the
electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalling system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F02 condition from the cockpit
fuse box.
Is it good?Replace the fuse.
Di sconnect the FLASH relay. Supply with
+12, the pole 4 of the relay. Are the left turning
lights turning on? Supply with +12 V the pole
5 of the signal relay. Are the right/left turning
lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
vnx.su