wheel DACIA SOLENZA 2004 User Guide

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 4
Power train group
The power train dismounting-remounting is to be performed on the engine compartment upper
part by means of a mobile lifting device.
The vehicle i s to be placed on a 2–columns
elevator.
Dismo unt :
- battery
- air filter inlet pipe;
- air filter assembly ;
- engine bonnet;
- front wheels.
Disconnect the oxygen sensor ( 1) connector
or the connectors of the two oxyge n sensors
(EURO 00 ).
Di smount : thermal protection screen and
descending tube from the exhaust manifold.
DISMOUNTIN G
Drain:
- the cooling circuit on the water pump
inlet pipe; - oil from gearbox;
- oil from engine if necessary;
- refrigerant fluid to a charging station
(vehicles with AC);
- oil from the power steering circuit
(vehicles with power steering).
- Oil from the power steeri ng circuit
(vehicles with power steering);
Dismo unt :
- engine shield;
- descending tube attachment screws
on support;
TIGHTENING MOMENTS) (daNm)
Right support attachment screw on engine 6.2
Hydr o-elastic buffer attachment nut 3.7
Left elastic buffer attachment nut 6.2
Whe els s c rew s 7.5
Power train- battery attachment screws 2.1
Connecting rod attachment nut on steering cross member support 6.2
Anti-roll connecting rod attachment screw on gearbox connecting rod 10.5
Control bar attachment screw on gearbox connecting rod 2.7
Pipes a ttachme nt s crews on comp ressor 2.1
High pressure pipe on DA pump 2.1
1
23
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 12
NO.DE NOM I NAT ION SERVICE DACI A
CODE ITEM NO
1O il plug wrench MOT 1018 1001101 800
2D evice for mounting the camshaft sealing gasket MOT 1127-01 1001112701
3Devic e for mounting crankshaft sealing gasket towards flywheel MOT 1129-01 1001112901
4Devic e for distribution belt tensioning MOT 1135-01 1001113501
5P liers for elastic clips MOT 1202-01 1001120 201
6Su itcase for petrol pressure checking MOT 1311-01 1001131101
7 Connection “J” MOT 1311-04 1001131104
8 Connection “K” MOT 1311-05 1001131105
9D evice for conne ction dismounting MOT 1311-06 1001131106
10 Pliers for valves oil seal ring dismounting MOT 1335 1001133 500
11 Device for checking the belt tensioning MOT 1505 1001150 500
12 Device for pi ston shaft mounting MOT 574-22 1001 0574 22
13 Sector for flywheel fixing MOT 582 1001 0582 00
14 Device for distribution gear blocking MOT 799-01 1001 0799 01
15 Device for mounting the crankshaft sealing gasket towards distribution MOT 550 1001 0550 00
16 Wrench for rockers adjustment MOT 567-01 1001 0567 01
17 Wrench for oil filter MOT 555 1001 0555 00
18 Device for power train sustaining MOT 545 1001 0545 00
19 Device for jackets maintaining MOT 484 1001 0484 00
or
Jackets maintaining clamps MOT 588 1001 0588 00
20 Comparing support MOT 251-01 1001 0251 01
21 Plate for measurement of cylinder jackets over-height MOT 252-01 1001 0252 01
Special tools
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 16
PISTONS
The bolt is fix mounted in the connecting rod
and free in piston.
Mounting direction: with the arrow towards
flying wheel. There are three matching classes with the
jacket.
Markings on pistons:1 – arrow towards flywheel
2 – piston class (A-B-C)
3 – items used by the supplier
Pistonclass Piston diameter (mm) Jacket diameter (mm)
A 75.765 - 75.775
*75.8 - 75.81*
B75.775 - 75.785*75.81 - 75.82*
C 75.785 - 75.795 75.82 - 75.83
The piston diameter is measured at the value
A = 46 mm.
Chara cteristics
* - these values are not included in classes.
Jacket marking
GreenBl ue
Red
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 19
- clearance B (mm):
- minim 0.02
- maxim 0.86.
AT T E N T I O N !
Protect the distribution belt and the accessories belt in order to avoid the water and
cleaning materials splashing on them.
Chara cteristics
OIL PUMP
The oil pump is a gear wheels type.
Oil minimal pressure at 80°C is :
- at idling 1 bar
- at 4000 rpm 3 bar
Dismount the oil pump and check the
gearing clearances.
Check:
- cleara nce A ( mm)
- minim 0.110
- maxim 0.249
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 21
CYLINDER HEA D DISMOUNTING
Drain the oil from the engine.
Dismount :
- wiring from the engine;
- compressor and/or power steering pump ( for vehicles equipped with air conditioning
unit and/or power steering); -compressor support and/or power steering pump support;
- alternator and its belt.
Dismounting – Remounting
Block the engine flywheel by means of the
MOT 582 device .
Dismou nt :
- oil dipper rod support;
- alternator belt tightening clamp;
-cr ankshaft pulley or pulleys ;
- pulley hub;
- distribution belt casings.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 27
CYLINDER S BLOCK DISMOUNTING
Dismount :
- water inlet pipe and oil dipper rod
guide ( their sealing is performed by means of
rubber rings that must be replaced at each dis-
mounting); - clutch;
-engine flywheel, immobilized by means
of the MOT 582 ;
- lower crankcase;
-cr ankshaft gear;
- tightening roller;
-cr ankshaft closing casing;
Dismounting – Remounting
- water pump. Dismount
the oil pump attachment screws.
Dismo unt the oil pump and its driving chain.
Ma rk the connecting rod caps compared
with the connecting rod body.
AT T E N T I ON!
Do not use punches for marking in or-
der to avoid cracks occurring; a perma-
nent marker is to be used.
Dismo unt
- connecting rods caps and the bearings;
- jackets maintaining device MOT 484 or
clamps MOT 588 ;
- assembly jackets-pistons-connecting
rods; - bearings caps a nd their bearings;
- crankshaft and axial clearance bearings;
- bearings from the cylinders block.
PISTONS SHAFTS DI SMOUNTING
Place t he piston on the support lining up
the piston bolt (shaft) with the gap whole from
the support (two T lines for marking the whole
center are facilita ting the lining up).
Remove the bolts using a press by means
of the extraction mandrel E.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 29
Dismounting – Remounting
The over-he ight X must be between 0.02
mm and 0.09 mm.
Place the jackets in such way that :
-the difference between two joint jackets
to be maximum 0.05 mm;
- the over-height to be in ascending order
between cylinders 1 and 4;
- in case of an incorrect over-height, check
the over-height by m eans of a new kit of jack-
ets, i n order to see i f t he c ause i s the block or
the cylinders jacket or check the theoretical size
values of the block and of the jackets. When over-height is correctly obtained, per-
form the A, B, C, D assembly then mark with
numbers jackets, pistons and the bol ts from 1
to 4 (no.1 towards flywheel) so that the corre-
s pondence with the corresponding connecting
rods may be achieved.
Pistons bolts mounting
The pistons bolts are fixed in connecting rods
and free in pistons. Mount the pistons bolts by means of the
MOT 574-22 that is containing:
- a support for piston ( S);
- an extracting mandrel ( M);
- the piston supporting bushings (B);
- the bolts for mounting ( A) provided with
their centering guides (C ). Use an electric plate of
1500 W (electric
oven) for connecting rods heating. Place the connecting rods on the electric
plate so that connecting rod end surfaces are
in contact with the heating plate.
Check if the pistons bolts are freely gliding
in the new corresponding pistons. Mount the piston bolt E on the mounting
bolt A.
Sc rew the centering guide C till end and
then unscrew it for a quarter of turn.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 30
The arrow marked on the piston head must
be oriented towards engine flywheel. The c onnecting rods ha ve no mounting
direction, but the ha lf-bearings spurs are to
be positioned on the same part. In order to assemble the piston and the
connecting rod, proceed as follows: -place the bushing B 13 on the support
and attach the piston (with the arrow oriented
upwards) on the bushing;
Dismounting – Remounting
- lubricate the centering guide and the
piston bolt with engine oil;
- check t he free gliding of the piston
bolt and the piston positioning.
When the connecting rod end is reaching
the necessary temperature (about 250 °C),
proceed to the ra pid of the piston bolt, as
follows: -introduce the centering guide in the
piston; - position the connecting rod i n the
piston;
-press till end the piston bold.
Check if the pi ston bolt is remaining re -
tired as against the piston outer diameter for
each of the connecting rod position in the pis-
ton.
Rings mounting
Mount the rings on the pi ston in the
following sequence: -
oiling ring ( 3);
-s ealing ri ng (2) w ith the mark “TOP”
upwards; -compression ri ng (1) with t he mark
“TOP” upward. The compression and sealing rings are to be
mounted with the slots disposed at 90° against
de bolt’s axle and displaced between them with
180°. The oiling ring is to be mounted with the
slot oriented at 45° against the bolt’s a xle.
The rings slots being adjusted, shall never be
reworked.
Lubricate the pistons with engine oil.
M ount the assemblies “connecting rod-
piston-rings” in the cylinder’s jackets, by means
of the mounting bushing. Mount the sealing gaskets on the cylinder
jackets.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 32
The axial bearings may have the following
thickness: 2.80, 2.85, 2.90, 295 mm.
M ount the connecting rods caps and
tighten to the required moment of 4.2 daNm.
Check:
-connecting rods lateral clearance;
- assembly rotation.
Mount: -gear and driving chain of the oil pump;
- oil pump (check the existence of the
centering bushings) and tighten the screws to
the required moment of 2.5 daNm;
Dismounting – Remounting
MOT 550
- the crankshaft closing casing; the
sealing is performed using LOCTITE 518 (
the layer H must be 0.6 – 1 mm thick);
- sealing gasket from crankshaft clos-
ing casing (lubricated with oil) by means of
the MOT 550 device;
-crankshaft sealing gasket towards fly-
wheel (at no. 1 bearing) by means of the MOT
1129-01 device. Lubricate the sealing gasket external part
and lip with engine oil.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 33
Mount the lower casing and tighten the
sc rews to the required moment of 1 daNm.
Sealing is performed using RHODORSEAL
5661; the l ayer D must be 3 mm thick.
Do not forget to replace the two half-moon
gasket (in area A ) with new ones.
Dismounting – Remounting
Mount the engine flywheel; the flywheel
attaching screws thread must be lubricate us-
ing LOCTITE FRENETANCH .
Block the engine flywheel by means of the
geared sector MOT 582 and tighten t he a t-
tachment screws to the required moment of 5
– 5.5 daNm.
Center the clutch disk and mount the clutch
mechanism (see chapter 20”Clutch”). Mount
the water pump (sealing is performed
using LOCTITE 518 ).
Apply a layer of sealant material H, 0.6 – 1
mm thick , according to the drawing.
Tight e n t he att achm e nt sc re ws to t he
required moment of 1 -2 daNm.
vnx.su