check engine DACIA SOLENZA 2004 Manual PDF

IGNITION AND INJECTION
17
17 - 84
ALP 1 IMPOSSI BILITY OF COMMUNICA TION UCE INJECTION CLIP TESTER
RECOMMEND AT IONS Nothing to be noticed
Ens ure t hat not the CLIP t ester is the cause of the f ailure, by trying to c ommunicate with the
computer of anothe r vehicle.
C heck connection between CLIP te ster and the vehicle diagnostic soc ket (cable condition).
C heck the condition of the injection fuse s, engine and cockpit.
M end if necessary.
C heck the presence of the supply +12 V at pin 16 and of the mass at pins 4 and 5 of the dia gnostic
device socket.
M end if necessary.
C onnect the 90 ways terminal box instead of the computer and check the insulation, continuity
and abse nce of the parasite resistance of the connections between: pin 28 injection computer > mass
pi n 33 injection computer > mas s
pi n 3 injection computer > mass
pi n 56 injection computer > p in 7 diagnostic socket
pi n 26 injection computer > p in 15 diagnostic socket
pi n 29 injection computer > fuse
pi n 30 injection computer > fuse
M end if necessary.
Fa ilure locating algorithm
AFTER Perform a checking by means of the CLI P tester.
REPARATION
vnx.su

IGNITION AND INJECTION
17
17 - 85
ALP 2 STARTING PROBLEMS engine is not starting or is difficulty starting)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
Ch eck that starter is well operating
Ch eck there is petrol in the fuel tank (fuel indicator failure).
Ensure that vehic le is supplied with adequate fuel.
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Ch eck the electric supply of the fuel pump.
Ch eck the good operation of the choke sensor.
Ch eck the motor of the idling regula tor.
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the engine compressions
Ch eck the flywheel condition
Ch eck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 86
ALP 3 IDLING PROBLEMS (unstable idling)
RECOMMEND AT IONS Do not consult this diagnostic but before performing a complete
checking by means of the CLI P tester.
C heck if there is petrol in the fuel tank (fuel indicator failure)
C heck if the vehic le is supplied with adequate fuel
C heck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
C heck the condition of the fuel filter
C heck the condition of the fuel tank
C heck that fuel tank aeration is taking place.
C heck the connection and the condition of the idling regulator connector.
Re place the connector if necessary.
C heck the motor of the idling regulator
In order to unblock it, you may slightly hit it.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
C heck the spark plugs and ignition coil condition
C heck tha t these eleme nts are specific to that vehicle.
C heck that the exhaust route is not clogged and the catalyst is not clogged.
Check, by means of the oil dipstick, that oil level is not too high.
C heck for lack of sealing at servo-brake (noise).
C heck the intake manifold condition
C heck if the valve body is not clogged
C heck the engine compressions.
C heck the engine flywheel condition
C heck the distribution setting on.
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 87
ALP 4 INTEMP ERATE ACCELERATION OR DECELERATION
(engine unstable running)
RECOMMEND AT IONS Do not consult this diagnostic but before a complete checking by
means of the CLIP tester
Ch eck if air filter is not deformed.
Ch eck if there is petrol in the fuel tank (fuel indicator failure)
Ch eck if the vehic le is supplied with adequate fuel
Ch eck tha t supply cir cuit hoses are not broken (espe cially further to a dismounting)
Ch eck the condition of the fuel filter
Ch eck the condition of the fuel tank
Ch eck that fuel tank aeration is taking place.
Disconnect the connection hose between the canister purging valve and the intake manifold.
Cl amp the connection hose in order to stop the air passing.
If there are no more disturbances, the cause is the canister purging valve.
Ch eck the spark plugs and ignition coil condition
Ch eck tha t these eleme nts are specific to that vehicle.
Ch eck that the exhaust route is not clogged and the catalyst is not clogged.
Ch eck the se aling of the exhaust manifold.
Ch eck, by means of the oil dipstick, that oil level is not too high.
Ch eck for lack of sealing at servo-brake (noise).
Ch eck the intake manifold condition
Ch eck if the valve body is not clogged
Ch eck the engine compressions.
Ch eck tha t brake calipers, drums and bearings are not gripped.
Ch eck that tires are inflated
Ch eck the engine flywheel condition
Ch eck tha t cooling system is properly operating
AFTER Perform a checking by means of the CLI P tester.
REPARATION
Fa ilure locating algorithm
vnx.su

IGNITION AND INJECTION
17
17 - 88
ALP 5ENGINE OPERATION BREAKDOWN
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these information but after performing complete
checking by means of CLIP tester.
Check the followings :
- fuel conformity;
- lack of air circuit clogging, supply circuit and fuel circuit;
- lack of important air leak;
- injection pump setting on;
- injectors.
vnx.su

IGNITION AND INJECTION
17
17 - 89
ALP 6ENGINE STOPPING
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings :
- lack of air circuit clogging, supply circuit and fuel circuit.
- lack of fuel leak
- injectors
- injecton pump
- engine
- supply +12V after setting on the contact at pin 81 of the injection computer.
vnx.su

IGNITION AND INJECTION
17
17 - 90
ALP 7ENGINE N OISE
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detecetd failures.
RECOMMEND AT IONSDo not use these information but after performing complete
checking by means of CLIP tester.
Check the followings:
- lack of a ir leak;
- pre-heating spark plugs;
- injection pump setting on;
- injectors;
- injection pump;
- engine;
- combustion pre-chambers.
vnx.su

IGNITION AND INJECTION
17
17 - 91
ALP 8SM OKE
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings:
- injection pump setting on;
- injectors;
- injection pump;
- lack of a ir leak;
- pre-heating spark plugs;
- engine.
vnx.su

IGNITION AND INJECTION
17
17 - 92
ALP 9LACK OF PE RF O RM ANCES
Failure locating algorithm
AFTERPerform a road test then a checking by means of CLIP tester.
REPARATIONFix possible detected failures.
RECOMMEND AT IONSDo not use these informations but after performing complete
checking by means of CLIP tester.
Check the followings :
- fuel conformity;
- lack of air circuit clogging, supply circuit and fuel circuit;
- lack of fuel leak and air leak;
- injection pump setting on;
- engine compression;
- injectors;
- injection pump;
- pre-heating spark plugs.
vnx.su

19
19 - 2
COOLING - EXHAUST - TANK
The heating radiator has no valve.
The fluid circ ulation is permanently done in the heating radiator, this leading to t he engine
cooling.
FILLING
Open the purging screw located on the water pipe between engine and climate control radiator.
Fill up the circuit by the expansion vessel hole
Tighten the purging screws in the moment when the fluid is flowing in a continuos jet.
Start the engine, maintaining it at 2500 rot/min.
Adjust the fluid level in the expansion vessel, during about 4 minutes.
Close the cap of the expansion vessel.
PURGING
Let the engine run for 10 minutes at 2500 rot/min, until engine fan starting (necessary
period for automatic gas purge).
Check if the fluid level in the expansion vessel is nearby the mark “Max”.
Do not open the purging screws with the engine running.
Ret ighten the expansion vessel cap with the warm e ngine.
Filling - Purging
vnx.su