steering DACIA SOLENZA 2004 Manual Online

INSIDE AND REAR LIGHTING
81
81 - 6
Lamps failures diagnostic
FOG LAMP NOT WORKING
Ye s
Ye s
Ye s Ye s
No
No No
No
Replace fuse F06
Replace the STOP contact
Replace fuse F19
Replace under steering
wheel control. Check fuse F06 from cockpit fuse box.
Is it worn?
Check the continuity and resistance against vehicle mass between:
- exit fuse F06 pin2 reverse driving contact c onnector
- pin1 reverse driving contact connector pin 6 right rear lam
connector
- pin 4 right rear l amp connector vehicle m ass
Ar e they good?
Defective wiring. Fix it.
Check fuse F19 from cockpit fuse box. Is
it worn? Check the continuity and
resistance against vehicle mass between:
- battery pin B2 light control lever and signaling,
- pin A3 inlet fuse F19,
- exit fuse F19 pi n 1 left rear lamp connector,
- pin 4 left rear l amp connector vehicle m ass.
Ar e they good?
Defective wiring. Fix it.

REAR DRIVI NG LAMP NOT WO RKING
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 3
The E.C.U. decoder has the following functions :
- deco ding the signal received from the anti starting
bushing; - send ing a code to the injection computer in order to
author ise the engine starting;
- c ontrolling the anti starting indic ator of the instrument
panel;
receiv ing the coded signal from the anti starting bearings,
for the vehicles equipped with RF remote control;
REMA RK :
In case both keys were lost, the code of the key head (8 characters) and the code of the
me tal insertion (4 characters) can be red from the vehicle-purchasing invoice. If also the
invoice was lost, the two mentioned codes can be found out based on the chassis s eries of that
vehicl e, acces sing the database of the DA C IA manufacture r, callin g the “C lient Voice”
department (phone 0248 500 000).
E.C.U. DECODER
General
- commandi ng the blocking/unlocking of the doors, if the vehicle is provided with RF remote
c ontrol keys;
- co mma nding the ceiling delayed light, for vehicles equipped with this system.
Th
e an ti starting bushing is located around the starting contact and is accessible after the
d ismounting the steering wheel’s half-cases. It catches the signal from the key head and then sends
a coded signal to the E.C.U. decoder.
The ve hicles equipped with RF remote control keys for blocking/ unlocking the doors are provided
with another anti starting bushing which transmits to the E.C.U. decoder also the signal received
from the RF remo te control.
Th e recognition of the two types of decoding bushings is performed by means of codes labelled
on their body, as follows : - code 04 2264J - for vehicles without RF remote control;
- code 8200 044257 - for vehicles with RF remote control. ANTI S TARTING BUSHING
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 7
If, further to the diagnostic by means of the CLIP tester, it is established the necessity of the
rep lacement of the anti starting bushing, proceed as follows:
- d isconnect the (-) terminal of the battery;
- d ismount the attachment screws of the steering wheel half-casings ;
- detach from clips the steering wheel half-casings;
- remove the steering wheel half-casings;
- d isconnect the anti starting bushing connector from the front wiring;
- remove the bushing;
- mount the new bushing outside the starting contact (anti theft mechanism);
- co nnect the bushing connector to the front wiring;
- a ttach in clips the steering wheel half-casings and mount the attachment screws;
- check the operation of the indicator and the anti starting system when the contact is off, then
with the contact on and then with the engine started.
Anti starting bushing replacement
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 28
Diag nostic
No
Is the anti starting bushing correctly fixed on
the steering column and is it correctly connected
?Position the bushing and fix its
connection.
Check the continuity and the isolation related
to the mass and the +12 V wiring.
Pin2 mass
Pin3 supply +IC
Pin4 pin A2 of the
E.C.U. decoder.
Is the wiring in good condition?
Fix the electric wiring.
Disconnect the E.C.U. decoder and check the
presence of +12 V at pin A2 of the wiring.
Is there any tension?Replace the anti starting bushing.
Connect t he E.C.U. decoder. Perform the
impulse detection t est with t he t ester CLIP
branched to the pin A2 of the E.C.U. decoder.
S et the contact on and check t he presence of
an impulse. Is there any impulse?
Replace the E .C.U. decoder.
Replace the key.
No
No
No
No
Yes
Yes
Yes
No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 39
Diagnostic – General
REMARK : the de coder bushing i s not
coded
DISMOUNTING – REMOUNTING
Dismoun t the half-cases under the steering
wheel, extract the bushing from the starting
contact and disconnect its connector.
CONNE CTING

Pin Denomination 1N ot in use
2 Mass
3+ After contact
4 Outlet signal
DESCRIPTION OF THE SYSTEM
By means of this system, the anti-starting is
activated few seconds after the contact has been
taken off (signalized by the blinking of the anti-
starting red indicator).
Its components are :
〈 key-head, equipped with a coded
electronic circuit (A).
OBSERVATION : the anti-starting
electronic is integrated in the remote control
printed circuit.
〈 anti-starting bushing (B), placed around the
ignition-start ing contact, equipped with an
electronic circuit having the purpose of key code
transmitting to the Cockpit Central Unit (UCH).
A
B
vnx.su

INSTRUMENT PANEL
83
83 - 4
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the 3 attachment screws of the steering wheel half-casing, by means of a TORX 20
screwdriver. Detach from clips the steering wheel half-casings and remove them.
By means of a TORX 20 wrench (“L” shaped), dismount the side attachment screws of the
upper dashboard. By means of a TORX 20 screwdriver dismount the two front attachment screws of the upper
dashboard. Detach from the three clips of the windscreen lower crossbeam, the upper dashboard.
Di smount the radio-tape pl ayer from the upper dashboard (if the vehicle is equipped with
radio): press its side c lips and extract it from the upper da shboard. Disconnect the a ntenna’s
connector and the radio-tape two connectors. Disconn ect the central locking switch connector (if the vehicle is provided with central locking).
Remove the upper dashboard towards vehicle right part.
By means of a TORX 20 screwdriver, dismount the a ttachment screws of the i nstrument
panel on the lower dashboard. Disconnect the four connectors of the instrument panel. Mark the identification mounting
position of the connectors.
R EMOU NT I NG
Perform the dismounting operations in the reverse order.
Perform functional tests of the instrument panel.
OBSERVATION: After battery reconnecti ng, re-program the clock and for the
vehicles equipped with programmable radio, reinsert the radio code.
P erform functional instrument panel
vnx.su

84
STEERING - CONN ECTOR
84 - 1
ANT I-THEFT MECHANISM
(IGNITION-STARTING SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control, electric system connecting and disconnecting, being provided in the same time
also with a steering locking device, with anti theft lock.
DISMOUNTIN G
Disconnect the battery (-) terminal
Dismount the 3 TORX 20 attachment screws of the steering wheel half-casings.
Detach from clips the steering wheel casings and remove them.
Disconnect the anti-starting bushing connector
Remove the anti-starting bushing ( 1) located around the anti-theft mechanism.
Disconnect the connectors ( 2) of the anti-theft mechanism.
Dismount the attachment screw (3) of the anti-theft mechanism by means of a screwdriver.
Bring the key on the position and push the mobile retaining pin ( 4) and releasing of the anti-
theft mechanism. Extract the mechanism towards backwards.
REMOU NT I NG
Position the contact key in the bellow position and push the mobile pin ( 4).
Mount the mechanism in its place, attaching it by means of the mobile pin and of the screw ( 3).
Connect ( 2) the anti-theft mechanism connectors.
Position and mount the anti-star ting bushing (1) around the anti-theft mechanism.
Connect the anti starting bushing connector.
Mount the steering wheel half-casings.
Connect the battery (-) terminal.
Check the operation of the anti-theft mechanism.
Anti-theft mechanism
vnx.su

84
STEERING - CONN ECTOR
84 - 2
The un der steering wheel control assembly and the rotating contact included in this one, can not
be separ ated.
DI SMOUNT I NG
Disconnect the battery (-) terminal.
Place the steering at the middle point (straight line driving position of the vehicle).
Detach from clips the steering wheel central ornament (cover).
Dismount the steering wheel attachment screw.
Carefully dismount the steering wheel in order not to damage “the tape connector” of the
ro tating contact; ensure that wheels are in the straight line driving position of the vehicle.
Dismount the TORX 20 three attachment screws of the steering wheel half-casing.
Detach from clips the steering wheel half-casings and remove them.
Disconnect the windscreen wiper switch connector and the connector of the turning and lighting
control switch. Loosen th e scr ew (1), u n blocking the under steering wheel control assembly from the attach-
ment co ne of the steering column.
Ex tract the under steering wheel control assembly from the attachment cone of the steering
co lumn.
RE M OUNT I NG
En sure that wheels are in the straight line driving position of the vehicle.
Position the under steering wheel control assembly so that after mounting the two steering
wheel half-casings, the assembly handles are lined up with the instrument panel and the dashboard.
Reconnect the windscreen wiper connector and the connector of the turning and lighting control
switch. Attach in clips the steering wheel half-casings. Mount their attachment screws.
Tighten the screw (1 ) in order to block the under steering wheel control assembly on the steer-
ing column. This operation is facilitated by a cutout in the lower half-casing, enabling access to the
screw ( 1).
Carefully mount the steering wheel in order not to damage “the tape conector” of the rotating
contac t; the steering wheel has an area without grooves on the steering column. Steering wheel
mu st easy enter in grooves.
Replace the steering wheel attachment screw ( TORX 50) after each dismounting ( pre-glued
screw) and tighten it (required tightening moment 4. 4 daNm ). Attach in clips the steering wheel
cen tral cover.
Reconnect the battery (-) terminal.
Check the operation of the under steering wheel control.
Under steering wheel control
1
vnx.su

84
STEERING - CONN ECTOR
84 - 3
Under steering wheel control
The under steering control assembly and the rotating contact included in this one are not to be
separated. The rotating contact is ensuring the electric connection between the steering column
and the steering wheel. This contact is connected with the from wiring by means of wires stacked
as tape-shaped having the necessary length provided to ensure 5 steering wheel rotations (limited
by the wheels camber plus one more for safety).
DISMOUNTIN G
AT T E N T ION !
It is forbidden the handling of the pyrotechnic system (airbag) near heating sources
or open fire, because there is a risk of undesirable starting of the system.
IMPORTANT !
Anytime when dismounting t he steering wheel, it i s necessary to dismount the airbag
connector (1). The airbag is provided with a connector who is short-circuited aft er
disconnecting the wiring connector, avoiding in this way all undesirable starting. Block the UCE airbag by means of the CLIP tester (see chapter 88 “ UCE airbag blocking” ).
The airbag indicator from the instrument panel is on. Disconnect the battery (-) terminal.
Set the steering on the middle point (straight on driving position of the vehicle).
Dismount the two attachment screws T ORX 20 of the airbag to the steering wheel.
Dismount the airbag connector ( 1).
Dismount the steering wheel attachment screw.
Carefully dismount the steering wheel for not damaging the “tape” connector of the rotating
contact; ensure that wheels are in straight-on vehicle driving position.
Dismount the three attachment screws TORX 20 of the steering wheel half-cases.
Detach from clips the steering wheel half-cases and remove them.
Disconnect the windscreen wiper connector, the lights and turning control connector and the
rotating contact connector. Loosen the screw (2 ) unblocking in this way the under steering wheel control assembly from
the attachment cone of the steering column.
Extract the under steerin g wheel control assemb ly off the attachment cone of the steerin g c olumn.
AT T E N T I ON !
It is forbidden the changing of the rotating contact position after dismounting the
under steering wheel control assembly because there is the risk of its damaging. The under steering wheel control – new i tem number- is provided with a pre-c ut
s elf-adhesive tape, stacked on the rotating contact and on the under steering wheel
control body that is not allowing the undesirable rotation of the rotating contact until
its m ounting on the attachment cone of t he steering column.
1
2
vnx.su

84
STEERING - CONN ECTOR
84 - 4
Under steering wheel control
R EMOU NT I NG
Ensure that steering is on middle point (wheels are in the straight-on driving position of the
ve h icle).
Position the under-steering wheel control assembly so that after remounting the two steering
wheel half-cases, the assembly handles are lined up with the instrument panel and the dashboard.
Reconnect the windscreen wiper connector, the lights and turning connector and the rotating
contact connector. Attach in clips the steering wheel half-cases.
Tighten t he screw ( 2) so that i s blocking the under-steering wheel control on the steering
column. This operation is facilitated by a cutting-out in the lower half-case allowing the access to
the screw ( 2).
Carefully mount the steering wheel in order not to damage the “tape” connector of the rotating
contact, the steering wheel is having an area with no grooves, that must be corresponding to the
no-grooves area from the steering column. The steering wheel must easy enter in the grooves.
Replace the steering wheel attachment screw (TORX 50) after each dismounting and tighten
it to the required moment ( 4.4 daNm).
Reconnect the airbag connector (10.
M ount the two attachment screws TORX 20 of the airbag (required tightening moment is
0.65 daNm) Reconnect the battery (-) terminal.
Check the operation of the under steering weel control.
IMP ORTANT !
Before reconnecting the driver’s ai rbag connector, it is necessary to apply a check-
ing procedure of the system: - check if the airbag indicator from the instrument panel is on, when the contact
is set on; - connect the inert igniter to the airbag connector (to the wiring) and check if the
airbag indicator is off; - set the contact off, connect the airbag connector instead of the inert igniter and
attach the airbag on the steering wheel (required tightening m oment is 0.65 daNm). AT T E N T I ON !
Any doubts regarding a good centering of the rotating contact involves the applying
of its centering method: carefully rotate clockwise the upper part of the rotating con-
tact 2.5 complete rotations (or until it gets blocked), then rotate anti-c lockwise 2.5
complete rotations. In case of a steering dismounting operation, of t he engine or of the t ransmission
elements implying the steering rack or steering column uncoupling, the steering wheel
must be immobilized. After everything has been remounted, perform an airbag system checking by means
of the CLIP tester. If everything is correct, unblock the UCE airbag and check if the
airbag indicator from the instrument panel is on for 3 seconds from setting the contact
on, then it is off and is remaining off. If the airbag indicator is not operating as a.m .,
see chapter “Diagnostic” and check the system by means of the “CLIP” tester. AT T E N T I ON !
All non-observing of these prescriptions may c ause an abnormal operation of the
sy stem, even an undesirable starting of it.
vnx.su