remote start DACIA SOLENZA 2004 Repair Manual

INSIDE AND REAR LIGHTING
Inside and rear lighting .................................... 81-1
Ceili ng lamp ...................................................... 81-4
Bulbs ... ............................................................... 81-5
Lamps failures diagnostic ................................. 81-6
Cockpit fuse box ............................................... 81-8
UCE de co de r protection .................................. 81-10
ACCOUSTIC WARNING - ANTI STARTING
General .............................................................. 82-1
One key head replacement ............................... 82-5
Dismounting - remounting E.C.U. decoder ..... 82-6
Anti starting bushing replacement .................. 82-7
R. F. remote control for blocking/unlocking the
doors ................................................................... 82-8
Electric control unit injection replacement ..... 82-9
Acoustic warning ............................................... 82-10
Pr ocedures ......................................................... 82-12
Diagnostic .......................................................... 82-18
Diagnostic – General ........................................ 82-39
Diagnostic – Failures interpretation ............... 82-53
Diagnostic – Conformity checking ................... 82-55
Diagnostic – States interpretation ................... 82-57
Diagnostic - Damage location algorithm ........ 82-63
INSTRUMENT PANEL
Instrument panel without RPM meter ............ 83 -1
Instrument panel with RPM meter ................. 83 -2
connectors disposal ........................................... 83 -3
Pe rform functional instrument panel ............ 83 -4
Speed transducer .............................................. 83 -5
F uel level transmitter ........................................ 83 -6
Water te mperature sensor ................................ 83 -7
Diagnostic – damages interpretation .............. 83 -8
STEERING - CONNECTOR
Anti-theft mechanism ...................................... 84-1
Under steering wheel control .......................... 84-2
Re ar windows defrosting switch ..................... 84-6
Central locking switch ...................................... 84-7
Pa ssenger electric window sw itch ................... 84-8
Driver electric window switch ......................... 84-9
Hazard sw itch .................................................... 84-10
Electric lighter..........................................................84-11
WINDSCREEN WIPER
Drive mechanism ............................................. 85-1
Diagnostic ........................................................... 85-3 AUTO RADIO
General .............................................................. 86-1
T apes player ...................................................... 86-6 CD Pl
ayer .......................................................... 86-7
C onnectors ........................................................ 86-8
Roof antenna .................................................... 86-9
ELECTRICAL ASSISANCE EQUIPEMENT
Windscreen washing ......................................... 87-1
Re lays and UCE decoder asse mbly from
cockpit ............................................................... 87-2
Cockpit Central Unit ....................................... 87-4
Diagnostic – general ......................................... 87-6
Diagnostic – Failures interpretation ................ 87-11
Diagnostic - Conformity checking ................... 87-14
Diagnostic – States interpretation ................... 87-18
Diagnostic – Damage location algorithm ........ 87-26
WIRING
Airbag - general ................................................ 88-1
Airbag – Electronic control unit ..................... 88-2
Driver’s airbag .................................................. 88-6
Airbag – Special devic es ................................... 88-9
The airbag destroying procedure .................... 88-10
Airbag diagnostic – General ............................ 88-12
Diagnostic – Failure interpretation ................. 88-14
Diagnostic – Conformity checking .................. 88-20
Diagnostic – Help .............................................. 88-22
Diagnostic – Failure locating tree .................... 88-23
Fr ont door wiring protector ............................ 88-24
Re ar door wiring prote ctor .............................. 88-25
ELECTRIC DIAGRAMS
General .............................................................. 89 - 1
Functional diagrams list .................................. 89 - 6
F unctional diagrams list index ............................ 89 - 8
Connections lists - Mass list ............................. 89 - 9
Electric compone nts location on vehicle ......... 89 - 10
Ma ss attachments on vehic le ............................ 89 - 10
Electric compone nts location on the vehic le .... 89 - 11
Cockpit fuse box ................................................ 89 - 14
Fu se box from engine compartment ................ 89 - 16
Wires functions index in connectors and
couplings ........................................................... 89 - 18
Wires functions in connectors and
couplings ........................................................... 89 - 21
Wires functions explanation ............................ 89 - 9581
82
83
84
85
86
87
88
89
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 1
This type of anti starting system is based on the key recognition, which has a special constructio n.
It may be separated in two elements which can be identified in the following way: the key head
(position A.) made of plastic, which c an be dismounted and the metal insertion (position B),
which is fixed and ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the engine starting In case of the system with ra dio frequency remote control (RF) of the doors blocking /
unlocking, the key head has a different construction, having an activation button of the remote
control and a red L ED, which i s lighted i n the moment of bl ocking/unlocking the doors, by
pushing the key button. Inside t he ke y head there i s the coded electroni c c ircuit for the anti
starting system and a printed electronic circuit, supplied by a battery, for the RF remote control
operation of blocking/unlocking the vehicle doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
AT T E N T I O N !
If the battery is low charged, the tension drop on the starter, at starting, may cause
the activation of the anti starting system and the engine starting is impossible.
General
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 3
The E.C.U. decoder has the following functions :
- deco ding the signal received from the anti starting
bushing; - send ing a code to the injection computer in order to
author ise the engine starting;
- c ontrolling the anti starting indic ator of the instrument
panel;
receiv ing the coded signal from the anti starting bearings,
for the vehicles equipped with RF remote control;
REMA RK :
In case both keys were lost, the code of the key head (8 characters) and the code of the
me tal insertion (4 characters) can be red from the vehicle-purchasing invoice. If also the
invoice was lost, the two mentioned codes can be found out based on the chassis s eries of that
vehicl e, acces sing the database of the DA C IA manufacture r, callin g the “C lient Voice”
department (phone 0248 500 000).
E.C.U. DECODER
General
- commandi ng the blocking/unlocking of the doors, if the vehicle is provided with RF remote
c ontrol keys;
- co mma nding the ceiling delayed light, for vehicles equipped with this system.
Th
e an ti starting bushing is located around the starting contact and is accessible after the
d ismounting the steering wheel’s half-cases. It catches the signal from the key head and then sends
a coded signal to the E.C.U. decoder.
The ve hicles equipped with RF remote control keys for blocking/ unlocking the doors are provided
with another anti starting bushing which transmits to the E.C.U. decoder also the signal received
from the RF remo te control.
Th e recognition of the two types of decoding bushings is performed by means of codes labelled
on their body, as follows : - code 04 2264J - for vehicles without RF remote control;
- code 8200 044257 - for vehicles with RF remote control. ANTI S TARTING BUSHING
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 4
REMARK :
The vehic les equipped with this anti starti ng system, have a type of decoder, and those
provided also with R F remote control for l ocking/ unlocking doors have another ty pe of
decoder.
Th e identification of the two types of E.C.U. decoder is realised by the inscriptions on the
labels as follows: - code P8200032783H and the in scri ption TRANS-PLAF for the vehicle s w ithout RF
remote control; - code P8200032776H and the inscr iption TRF-TRANS-CAR for the vehicles with RF
remote control. ANTI STARTING INDI CATOR
It is located on the instrument panel (position A) and has the following functions:
- signalising the activation of the anti starting system;
- signalising the case of non identifying the key head;
- signalling the entrance in the operation mode “resynchronisation” of the remote controls, RF
with E.C.U. decoder, for the vehicles which use the RF remote control.
When the contact is off and the anti starting system is activated, without any existing failure, the
an ti starting indicator must blink slowly (a blink per second).
After setting the contact on, the anti starting indicator must light for 3 seconds and then turn off.
If a fter setting the contact on, the anti starting system doesn’t work properly, then the anti
starting indicator will blink rapidly (two blinks per second). Th
e ceiling delayed lighting is activated subject to the position of the light glass ( 1):
- position A the ceiling is lighting permanently;
- position B de layed ceiling lighting; this will light for 15 seconds after driver’s front door closing
or after the command of unlocking the doors with the RF remote control. This delay turns out in the
mo ment of setting the contact;
- po sition C ceiling light off.
General
AA
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 5
After ordering a new key head based on the alphanumeric code mentioned on the invoice,
dismount the old key head and remove the metal insertion (mechanical part), then introduce the old
meta l insertion in the new key head according to the previously mentioned procedure. In case the
key head is provided with RF remote control for blocking/ unlocking the doors, after its replacement,
pe rfor m the synchronising procedure of the RF remote control with the decoder, subject to the
fo llowing cases:
- a fter the replacement of the RF key, perform the “Specific synchronised procedure” in order
to bring into phase the RF remote control with the decoder. - if both keys are replaced, perform the “Simple synchronised procedure” for the first RF key
and the “Specific synchronised procedure” for the second one RF key.
If a key was lost, a new key head and a metal insertion are to be ordered.
One key head replacement
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 6
All new decoders, are not coded. After mounting on the vehicle, it is necessary the memorisation
of the key head code by the decoder in order to be operational. If only the decoder is replaced, no
intervention is necessary to the injection computer, which will keep the old anti starting code. When
the vehicle is provided with RF remote control for blocking/unlocking the doors, the performing of
the resynchronisation of the keys with the decoder is imposed, after its mounting. If further to the
di ag nostic of the anti starting system, using the CLIP tester, the replacement of the decoder is
imposed, proceed as follows:
DISMOUNTIN G
- disconnect the (-) terminal of the battery;
- d ismount the ECU decoder-relays assembly;
- ro tate the ECU decoder assembly, in order to have access at its rear connectors;
- d isconnect the front wiring connector from the E.C.U. decoder;
- deta ch ECU decoder from clips of the relays-ECU decoder support.
REMOU NT I NG
- attach in clips the new E.C.U. decoder in the support, connect the front wiring connector to
the ECU decoder, then attach the assembly on the driving post cross member in its place and
mo unt its attachment screw;
- remo unt carefully the access flap of the fuse box;
- reconnect the (-) term inal of the battery.
Proceed then to the insertion of the anti starting code using the contact key, then to its me morising
(va lidation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder replacement procedure and anti starting code memorising”. Check then the correct operation
of the anti starting system with both keys.
ATTENTION!
Once the decoder has memorised the key codes, this code cannot be erased or replaced
with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), then the “ Kit
replacement procedure” must be performed.
Dismounting - remounting E.C.U. decoder
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 8
The RF remote control has only the function of blocking/ unlocking the doors. The RF remote
c ontrol with evolutionary code can use only two keys as the decoder may manage only two different
e volutionary codes.
Th e key heads have an identification number formed by eight alphanumeric characters (letters
and fi gures), beginning with letter E. In case of loosing one key, a key head and a metal insertion
will be ordered, then the resynchronisation procedure of the RF remote control of the key with the
de coder from the vehicle must be performed.
If the ve hicle is provided with RF remote control key and this one has been replaced, then
pe rfor m the “ Simple synchronised procedure “. When the vehicle has both keys with RF remote
contro l, then perform the “Specific synchronised procedure “ after the replacement of the second
key.
REMA RK:
If only one key head is replaced, usually there is no need for resynchronisation of the
other RF remote control.
If both RF re mote controls are desynchronised, one procedure of resynchronisation will
be performed w ith each remote control: perform the “Simple synchronisation procedure for
the first R F r emote control” and the “Specific synchronisation procedure” for the second
RF remote control.
Check then, the operation of doors blocking/ unlocking with both RF r emote controls.
R.F. remote control for blocking/unlocking the doors
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 13
Procedures
1. Return to “COMPUTER TEST”
2. Set the contact on for 2 seconds in “ M” position, without start ing the engine. The anti
starting indicator will begin to blink rapidly.
3. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE ………………………………......…… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….…… PASSIVE
10. Take the c ontact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE LIST”, which now, must be like that: 18G FIRST CYCLE MEMORISING…………………………….....…ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………….……..PASSIVE
19D UNBLOCKED KEY PROGRAMMING …………………..…… PASSIVE
13. Set the contact i n “M” position for 2-3 seconds in order t o send the code t o the E.C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI STARTING” is “ ACTIVE”.
Perform the synchronisation of the TRF remote control with the decoder (with 1or 2 keys).
OBSERVAT ION:
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows:
- take the contact off; wait for 10 seconds, then the anti starting indicator will blink;
- in the menu, “COMMAND MODE” access “ ACTUATORS” then validate “ FORCED
PROTECTION MODE” launching the command from the blue button situated on the ri ght
topside of the screen. “COMMAND IN PROGRESS” will be displayed and then “FINISHED
COMMAND”; - in t he m enu “ STATE LIST” search for the state 10G ”ANTI START ING”, which
must be “ ACTIVE”; - set the contact on “M” position; the anti starting indicator will blink rapidly, and the
engine starting is impossible;
- remove the key from the contact and check then the engine starting with both keys, so
the procedure is finished.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 14
Procedures
RE M ARK:
For the RF remote control synchronisation, after the replacement of an E.C.U. decoder,
the sync hron is ation proced ure must be per formed taking i nto account the foll owing
situations : - fo r one RF remote control, perform the “ SIMPLE SYNCHRONISED
PROCED URE ”;
- for the second RF remote co ntrol per form the “SPE CI FI C SYNCHRONI SED
PROCED URE ”.
B. KIT REPLACEMENT PROCEDURE
(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder;
- memorising of the new anti starting code by the injection computer; it is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Inform by phone at ”Client Voice” (phone no 0248 500 000), the vehicle chassis series and
the key heads code, written on the vehicle invoice, in order to get the repairing code.
3. Connect the CLIP tester t o the diagnostic socket and to the battery (or to the lighter
s ocket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting it
off the vehicle, as follows:
- select vehicle type “B41”;
- enter the menu “ COMPUTER TEST” then select “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configuration s : petrol/diesel, programming with 1 or 2 keys, ceiling delayed light,
the type of the doors’ blocking switch (CPE), etc.
4. Return to the menu “ANTI START ING”.
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STAT E LIST”; here you
must find the following states: 18G FIRST KEY MEMORISING……………………………........… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………………..... ACTIVE
19D UNBLOCKED KEY PROGRAMMING ……………………..... ACTIVE
REMARK:
If the state 19G and 19D are not “ACTIVE” this means the E.C.U. decoder isn’t a
ne w one and cannot memorise another anti starting code.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su