ECO mode DACIA SUPERNOVA 2004 User Guide

82A
HORN - ENGINE IMMOBILISER
82A - 12
7. Get back to “ TEST COMPUTERS”
8. Set the contact on for 2 seconds in “ M” position, without start ing the engine. T he a nti
starting indicator will begin to blink rapidly.
9. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE…………………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………………PASSIVE
10. Take t he contact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”.
11 . The anti starting indicator will blink rarely.
12. Get back to the “STAT E LIST”, which now, must be like that:
18G FIRST CYCLE MEMORISING ………………………………ACTIVE
19G NOT PERFORMED KEY PROGRAMMING... ………………PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………. PASSIVE
13. Set the contact in “ M” position for 2-3 seconds i n order t o send the code to t he E .C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI START ING” is “ACTIVE”.
Pe rform the synchronisation of the TRF remote control with the decoder (with 1 or 22 keys).
OBSERVAT ION
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows: -take the c ontact off; wait for 10 seconds, then the anti starting indicator will
blink; -in the m enu “COMMAND MODE” access “ ACTUATORS” then validate “
FORCED PROTECTION MODE” launching the command from the bl ue button
s ituated on the right topside of the screen. “COMMAND IN PROGRESS” will be
displayed and then “FINISHED COMMAND”.
-in the menu “STATE LIST” search for the state 10G ”ANTI STARTING”,
which must be “ ACT IVE”;
-set the contact on “M” position; the anti starting indicator will blink rapidly,
and the engine starting is i mpossible; - remove the key from the contact and check then the engine starting with both
keys, so the procedure is finished. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 13
NOTE
For the RF remote control synchronisation, after the replacement of an E.C.U.
decoder, the synchronisation procedure must be performed taking into account the
following situations: -for one RF re m ot e c ont ro l , pe rf orm t he “ SIMP L E SY NC H RONIS ED
PRO CEDURE”;
-f or the second RF remote control perform the “SPECIFIC SYNCHRONISED
PRO CEDURE”.
B. KIT REPLACEMENT PROCEDURE(E.C.U. decoder plus 2 key he ads)
In case of one kit replacement perform the following steps:
- memorising the anti starting code by the E.C.U. decoder
- memorising of the new anti starting code by the injection computer; i t is necessary the
repairing code (found out based on the old ke y heads code) and t he CLIP tester.
Perform the actions in the following sequence:
1. Mount the metal insertions of the old keys to the new key heads.
2. Send to Tech Line the key heads code, written on the vehicle invoice, in order to get the
repairing code. 3. Connect the CLIP tester to the diagnostic socket and to the battery (or t o the lighter
socket) of the vehicle. Read the configuration of the old E.C.U. decoder before dismounting off
the vehicle, as follows: - select vehicle type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”;
- access “COMMAND MODE” then “READ CONFIGURATIONS”;
- note the configurations : petrol/diesel, programming with 1 or 2 keys, ceiling delay, the
type of the doors’ blocking switch (CPE), etc.;
4. Get back to the m enu “ANTI STARTING”;
5. Dismount the old E.C.U. decoder and replace it with a new one, the contact being off.
6. Check the configuration of the new E.C.U. decoder selecting “ STATE LIST”; here you
must find the following states: 18G FIRST CYCLE MEMORISINGPASSIVE…………………INACTIVE
19G NOT PERFORMED KEY PROGRAMMING ……………….ACTIVE
19D UNLOCKED KEY PROGRAMMING ………………………ACTIVE
NOTE
If the state 19G and 19D are not “ACTIVE” this m eans the E.C.U. decoder isn’t a
n ew one and cannot memorise another anti starting c ode. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 14
7. Set the contact in “M” position with one of the keys (without starting the engine), for about
2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ……………… ACTIVE
8. Set the contact with the second key (without starting the engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;9D RECEIVED KEY CODE………………………………………. ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
- case (b)- the second key does not belong to the vehicle or the first key was used once again;
9D RECEIVED KEY CODE………………………………………PASSIVE
19G NOT PERFORMED KEY PROGRAMMING……………… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In t he menu “COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Get back to the “ STAT E LIST”, which now must be as follows: 18G FIRST CYCLE MEMORISING……………………………... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………… PASSIVE
19D UNLOCKED KEY PROGRAMMING………………………PASSIVE
13. In the m enu “COMMAND MODE” choose “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”. Get back to t he “STATE LIST “ and check the state:
9G FORCED PROTECTION MODE …………………………….. ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink rapidly. Check
in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” access “ACTUA TORS”, then select the command “
MANUAL INTRODUCTI ON CODE”. Type the four figures of the repairing code, then validate
with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS” will
appear and then “FINISHED COMMAND”. 16. Take off and then set again the contact, without starting the engine, in order to send the
new anti starting code to the injection computer. The anti starting indicator will light for 3 seconds,
and then it will turn off.
17. The procedure is finished. Check the engine starting with both keys. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 15
NOTE
For the RF remote control synchronisation, after the replacement of a kit, take into
account the fol lowing situations: - for the first RF remote control, perform the “ simple synchronised procedure”;
- for the second RF remote c ontrol perform the “specific synchronised procedure” .
C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by the means of the CLIP tester. This is possible
only if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed
by the state: 10G ANTI STARTING…………………………………………….. ACTIVE
After getting from DACIA database the repairing code (based on the code from the vehicle’s
key head), perform the following operations. 1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle. 2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “SUPERNOVA” and “050” equipping level.
5. Select the menu “ COMPUTER TEST” then choose “ ANTI STARTING”.
6. In the menu “ STAT E L IST” find t he state 10G “ANTI STARTING” which m ust be
“ACTIVE”.
7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL INTRODUCTION CODE” where you will write the
repairing code (formed of four figures), then validate it with the key “ENTER”. T he message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”.
9. Now the procedure is finished and you may start the vehicle engine.
AT TENT ION
You may perform three essays of introducing the repairing code; if aft er the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then put it
again, other t hree essays being allowed.
NOTE
This procedure does not decode the injection computer, but allows only the start of
the vehicle’s engine. After ten minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 16
D. SIMPLE S
YNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations:
- the RF remote control c ode is no longer i n the range of the E.C.U. decoder re ception,
because of consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E.C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.)
The following operations will be performed: - take off t he contact
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/o pening course.
- the procedure of synchronisation is finished; check the blocking/ unlocking by pushing
the RF remote control.
OBSERVAT ION
Duri ng those 10 seconds you can visualise by means of the CLIP tester the state 17G
“THE PROGRAMMING IN PROGRESS OR THE TIR/TRF
RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E .C.U. decoder
and will be performed as follows:
- connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket) of
the vehicle. - select the vehicle type “SUPERNOVA” and the “050” equipping level;
- select the m enu “ COMPUTERS TEST” then “ ANTI STARTING”
- enter the m enu “COMMAND MODE” and select “CONFIGURATION”
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course.
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice the RF remote control button; the doors will block and then unlock and the
anti starting indicator will t urn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control. PROCEDURES
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 18
If the states
remain unchanged, check the following:
- electric connections of the decoding bushing
- the electric connections between the E.C.U. decoder and the decoding bushing
- the tension of the battery must have more than 8V when the starter is activated.
If all these are conformable, proceed to the replacement of the decoding bushing, and then
check again the a .m. states.
II. SOLVING MODE
When an electric ke y head (or both) is damaged, order (Info TECH LINE 0248/213766) a
new set of two electronic heads, subject to the vehicle type, as follows: TRF key head set – item no. 6001 543 684, 1 set, for DSN equipped with
anti intrusion (CLIMA or RAPSODIE)
TR-TRF key head set – item no. 6001 544 452, 1 set, for DSN without anti
intrusion (CLIMA or RAPSODIE)
TR key head set – item no. 6001 543 683, 1 set, for DSN EUROPA
Send to Tech Line (0248 213766), the chassis series no, the anti starting code of the damaged
key heads, the a nti starting code of the ne w key heads, and they will sent at their turn, to the
service center, the repairing code (taking into account that this code has a special regime). Additionally , there are necessary the new key heads, the E.C.U. decoder (obligatory TRF, if
the vehicle is equipped with central locking), the repairing code of the computer; proceed then to
the replacemen t of these items performing the following operation:
A) Replacement- c hecking electronic key heads :
Replace t he damaged key heads with the new ones (the metal insertions remain the same),
then by means of the CLIP tester, selecting COMPUTER TEST- ANTI STARTING- STATE
LIST, check following states with both keys:
If the states are in the following configuration, when setting the contact on, consecutively with
both keys:
ANTI STARTING……………………………………………..........ACTIVE
RECEIVED KEY CODE………………………………………….. ACTIVE
ACCEPTED KEY CODE…………………………………………PASSIVE DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 20
D)
Memorising of the new code of the injection computer
- in ACTUATORS
launch the command MANUAL INTRODUCTION CODE ; type
the repairing code of the old key kit, then validate it with the key
ENTER.
- the message “COMMAND IN PROGRESS ” will be displayed followed by the message
“FINISHED COMMAND ”.
-s et the contact on; t he anti starting LED indicator will start blinking, then take off the
contact;
-set the c ontact on for 10 seconds ; take off the contact;
- check if the engine starts with the two keys.
If the engine doesn’t start, repeat this operation (point D).
E) Key resynchronisation (remote controls)
-if the vehicle is equipped with only one remote control, its resynchronisation will be
performed as follows (simple resynchronisation);
- with t he contact taken off, push continuously on the c entra l l ocking but ton from the
dashboard, up to the moment the anti starting LED indicator remains lighted (the doors actuators
are performing a closing/opening course.) From this moment, t he operator has 10 seconds to
perform the next operation; - push twice on the remote control (the doors actuators are performing a closing/opening
course.) and the anti starting LED indicator turns off; - if the vehicle is equipped with two remotes controls, perform the simple resynchronisatio n
procedure for the first key and a specific resynchronisation procedure for the second key, with
the CLIP tester as follows: - in COMPUTER TEST select ANTISTARTING with t he c ontact t aken off, then
COMMAND MODE , CONFIGURATION ; launch the command PROGRAMMING OF
THE SECOND TIR/TIE KEY and validate (the doors actuators are performing a closing/
opening course.). Then within 10 seconds, push twice on the remote control (the doors actuators
are performing a closing/o pening course).DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 39
THE CONFORMITY CHECKING
Next, the checking of different states and configurations of the anti starting system is to be
performed.
In case of finding some failures at the diagnostic by means of
RECOMMENDATION the CLIP tester, analyse them based on the diagnostic (ALP)
corresponding to the respective failure.
Nr.
crt.Function State / configuration Observ
at i ons
1. Conformity E.C.U decoder Computer identification Display of the E.C.U.
decoder item
2. Remote control type 2G = remote control IR = infrared configuration RF = radio frequency
3. Dome ceiling Without dome ceiling or Validation on the blue button
with dome ceiling on CLIP screen
4. Key programming 3G = configuration key With one or 2 keys
programming
5. Configuration petrol/ diesel 3D = configuration coded Without = for petrol engine dies el electric valve With = for diesel engine
6. Forced starting protection 9D = forced protecting mode ACTIVE = only after
validation on the blue button
7. Anti starting state 10G = anti starting ACTIVE = with the contact
taken off or after 10 seconds
from the co ntact taken off
8. Key presence 8D = key present ACTIVE at the setting on the
c ontact if there is a coded key.
NOTE: the states 8D, 9D,
10 D must be ACTIVE at a
co rrec t operation
9. Code key receiving 9D = received key code ACTIVE at the setting on the
contact if the key is coded in
a good format
10 . Correct key code 10D = right key code ACTIVE at the setting on the
contact if the key is coded in
a good format and has the
correct code.
NOTE: after the analyse of the states 8D, 9D, 10 D the
co ntact will be set o when
the LED indicator blinks
(
ACTIVE anti starting)
DIAGNOSTIC
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su

86
RADIO
GENERAL
C ode protection
T he radio is protected by means of a four digit code. This code is introduced by the
radio keys at each battery disconnection.
Co de introduction by means of the radio keys : in order to valid one digit introduction,
push the next key ( see the operation technical book).
In case of a wrong code, the instrument is getting blocked ( one minute for the first error, two
minutes for the second error, four minutes for the third…)
Af ter first code introduction, some confi gurations must be programmed ( see chapter”
configuration”). These are remaining programmed till battery disconnection.
NOTE : the return to the “wave jammer” mode is possible by simultaneously push-
ing of the keys 2 and 5, putting the radio under tension. Wait then for two minutes.
Programming
OBSERVATION : in order to select the radio operation are a, push simultaneously keys 2
and 5, putting the radio under tension. Wait then for about two minutes. Introduce the four digits
code, then:
-s elect the adequate area
86 - 2
25
-America
-Japab
-Asia
-Arabia
-Othe rs (Europa, Africa, others…)
-Select the sound tonality curves:
- 0 : inactive adjustment
- 1 : Tw i n g o
- 2 : Clio
- 3 : Mégane
- 4 : Laguna
- 5 :
T op ra nge
- speakers number configura tion – with or
w ithout rear speakers (REAR ON / OFF)
NOTE : it is not necessary to perform the configuration after radio code introduction,
further to a supply failure.
vnx.su